United Kingdom version. Metric throughout, set up for S275 with the BS EN 10025-2 tensile figure, and with notes on how PUWER treats mechanical and hydraulic press brakes. US version

Press Brake Tonnage Calculator (UK, tonnes and S275)

Bending force in tonnes and kN per metre for S275 and S355 steel or SWG sheet in mm, with V-die rules and the PUWER inspection rules for mechanical press brakes.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Press Brake Tonnage Calculator?

British fabrication shops bend structural grades to BS EN 10025-2, mostly S275 and S355, and rate their brakes in metric tonnes. This version starts on a 4 mm S275 bend 2 metres long, with the tensile strength set to the 410 N/mm² minimum the standard gives for S275 between 3 and 100 mm thick. In the usual 32 mm die (8 x T) the air bend needs about 66.8 tonnes, or 33.4 tonnes per metre.

The minimum is a floor, not a typical value, and delivered steel is often stronger. If the mill certificate shows a higher figure, type it in, because the force rises in proportion. S355 starts at 470 N/mm², about 15% more force than S275 for the same bend.

Before a job goes on the brake, compare both numbers with the machine and the tooling: the total against the press rating, and the tonnes per metre against the punch and die rating, which is often the tighter limit on short, heavy bends.

  • Air bending, bottoming and coining force
  • US tons, metric tonnes and kN, per length and in total
  • Material presets by tensile strength or custom UTS
  • Inside radius and minimum flange rules for the chosen die
  • Die opening comparison table and press capacity check
Read the guide: Press Brake Tonnage, V-Die Width and the Air-Bent Radius

Updated

How to use the Press Brake Tonnage Calculator

  1. Keep the units on metric and enter the thickness and bend length in mm.
  2. Leave the die on the 8 x T rule, or choose "My die" and enter your V opening.
  3. For S275 or S355 keep "Custom tensile strength" and type the value from the mill certificate (at least 410 or 470 N/mm²).
  4. Enter your press capacity in tonnes to see how much of it the bend uses.

Worked examples

4 mm S275, 2 m bend, 32 mm die

Input

T 4 mm, V 32 mm (8 x T), 2,000 mm, UTS 410 N/mm², air bending

Output

66.78 t total (654.9 kN), 33.39 t/m, inside radius about 5.1 mm

Fine on a 100 tonne brake. Moving to a 40 mm die cuts the force to 53.42 t but opens the inside radius to about 6.4 mm and the minimum flange to about 28 mm.

6 mm S355, 1.5 m, 50 mm die

Input

T 6 mm, V 50 mm, 1,500 mm, UTS 470 N/mm², air bending

Output

82.67 t total (810.8 kN), 55.12 t/m

S355 at its minimum tensile strength already needs about 14% more than the 60 ksi mild steel baseline. At 55 t/m, check the tooling rating per metre as well as the 100 tonne press rating.

16 SWG mild steel tray, 2.5 m

Input

T 1.626 mm (16 SWG), V 12 mm, 2,500 mm, mild steel 414 N/mm²

Output

37.12 t total, 14.85 t/m

A long thin bend is light work per metre, but still uses over a third of a 100 tonne brake. Bottoming the same bend would need about five times the force.

Background and insight

The working formula in tooling catalogues and press makers’ charts is tons per foot = 575 x T² / V, with T and V in inches, for a 90° air bend in mild steel of 60,000 psi tensile strength (AISI 1035 cold-rolled is the usual baseline). Force rises with the square of thickness, because both the bending moment and the section that resists it scale with T, and falls with the die opening, because a wider die gives the punch more leverage. Other materials are scaled by their tensile strength divided by 60 ksi.

In metric units the same relation is about 1.6 x UTS x T² / V in kN per metre, with UTS in MPa and T and V in millimetres. European and Asian brake makers often publish a version with a constant of 1.42 and a 450 MPa baseline, which gives a few percent less; both are rules of thumb for 90° bends and should be checked against the chart for your press.

Air bending touches the sheet at only three points, so the force is low and the radius is set by the die, roughly 15 to 17% of V in mild steel, 20 to 22% in 304 stainless and 13 to 15% in 5052-H32 aluminium (Steve Benson’s 20% rule in The Fabricator; some of his columns put 5052-H32 nearer 11 to 13%, so confirm with a test bend). The calculator uses the middle of each range. Bottoming presses the sheet into the die and needs around five times the air-bend force; coining drives the punch tip into the material and needs ten times or more, which is why it is rarely used on modern brakes.

Common use cases

  • Checking a job against the press

    Make sure the total force and the force per metre stay inside the press and tooling ratings before setting up.

  • Choosing a V-die

    Balance force against inside radius and minimum flange length when picking the die opening.

  • Design for manufacture

    Check that flange lengths and radii on a drawing can actually be formed on the available tooling.

  • Quoting thicker work

    Find out quickly whether a plate job needs a bigger brake or a subcontractor.

Tips and limitations

  • Under PUWER, a mechanical press brake with a flywheel and clutch is a "power press": its guards need a thorough examination at least every 12 months with fixed guards only, every 6 months otherwise, and an inspection and test by an appointed person within the first four hours of each shift.
  • Hydraulic press brakes have no clutch, so the power press regulations (32 to 35) do not apply to them, but the general PUWER duties on guarding, maintenance and training still do.
  • Bend S355 and thicker S275 across the rolling direction where you can. Bending along it is more likely to crack the outside of a tight bend.
  • Spread long heavy bends evenly along the bed and keep short ones in the centre to protect the ram and the tooling.

Sources and further reading

  1. Safe use of power presses (L112), Health and Safety Executive. PUWER regulations 32 to 35, the power press definition and examination intervals.
  2. Steel material properties, Steel Construction Institute. BS EN 10025-2 yield and tensile strengths for S275 and S355.
  3. Die width selection, The Fabricator. V opening relative to thickness.

Frequently asked questions

How many tonnes do I need to bend 4 mm S275?

About 33.4 tonnes per metre in a 32 mm die at the 410 N/mm² minimum tensile strength, so 66.8 tonnes for a 2 m bend. Use the mill certificate value if it is higher; the force scales with it.

What tensile strength should I use for S275 and S355?

BS EN 10025-2 sets minimums of 410 N/mm² for S275 and 470 N/mm² for S355 for thicknesses over 3 mm and up to 100 mm. Real plate is usually above the minimum, so for a safe estimate of the force use the tensile strength on the mill certificate.

Do the power press regulations apply to press brakes?

To mechanical ones. HSE's L112 defines a power press as a press or press brake for working metal that is power driven and has a flywheel and clutch. Pneumatic and hydraulic presses have no clutch mechanism and fall outside regulations 32 to 35.

How often must a mechanical press brake be thoroughly examined?

At least every 12 months if it has fixed guards only and at least every 6 months otherwise, and after any exceptional circumstances that could affect safety. A competent person carries it out and the employer keeps the report.

How do I convert press brake tonnes to kN?

Multiply by 9.807. A 100 tonne brake is about 981 kN. The calculator shows tonnes, kN and US tons together, which helps when the manual for an imported machine quotes US tons.

Is there an in-depth guide to the Press Brake Tonnage Calculator?

Yes. “Press Brake Tonnage, V-Die Width and the Air-Bent Radius” covers the background, how it works, common pitfalls and worked examples. Read the full guide.