Australia version. Millimetres and cc by default, with Australian pump grades in mind: the national fuel standard sets 91 and 95 RON minimums, and 98 is sold as a premium. US version
Compression Ratio Calculator (Australia)
Static and dynamic compression ratio in millimetres and cc, with head gasket, deck and piston volumes, for engines running Australian 91, 95 or 98 RON petrol.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Compression Ratio Calculator?
Australian bowsers are labelled by research octane number. The Fuel Quality Standards (Petrol) Determination 2024 sets a 91.0 RON minimum for regular unleaded and 95.0 for premium, with up to 10% ethanol allowed (E10). 98 is a premium product sold above the 95 minimum. US articles quote octane as a pump average, several points lower, so a US "91" build is not the same fuel as an Australian 91.
This version opens in millimetres with a large inline six of 92 mm bore and 99 mm stroke, the sort of engine Australians rebuild and boost. Enter the chamber in cc, gasket bore and compressed thickness, deck clearance and piston dish or dome, and the calculator gives the static ratio and a breakdown of the clearance volume. Add rod length and intake closing for the dynamic ratio.
- Static compression from bore, stroke, chamber, gasket, deck and piston volumes
- Dynamic compression from rod length and intake valve closing, using slider-crank geometry
- Breakdown bar of every part of the clearance volume
- Chamber volume needed for a target ratio, plus what ±2 or ±4 cc and a thicker gasket would do
- Inch or millimetre inputs, copy and share link
Updated
How to use the Compression Ratio Calculator
- Choose inches or millimetres and enter bore and stroke.
- Enter the combustion chamber volume in cc, measured or from the head maker.
- Enter the head gasket bore and its compressed thickness, then the deck clearance (positive if the piston sits below the deck at TDC).
- Enter the piston volume: dish and valve reliefs as a positive number, a dome as negative.
- Read the static ratio and the breakdown of clearance volume. Switch on dynamic compression and enter rod length and intake closing angle (degrees after BDC) to see the dynamic ratio.
- Optionally enter a target ratio to see the chamber volume that would give it.
Worked examples
Inline six on a 1.0 mm gasket
Input
92 x 99 mm, 52 cc chamber, 93 mm x 1.0 mm gasket, 0.3 mm deck, 8 cc dish, 160 mm rod, intake closes 50° ABDC
Output
Static 10.57:1, dynamic 9.30:1
Each cylinder sweeps 658 cc over a 68.8 cc clearance volume. The target field shows that 10:1 would need a 56.3 cc chamber.
Thicker gasket to make room for boost
Input
Same engine, 1.5 mm gasket
Output
Static 10.12:1, dynamic 8.91:1
The extra half-millimetre adds 3.4 cc. It is a common first step, though it also opens up the squish gap, which can affect knock.
Smaller dish pistons for a 98 build
Input
Same engine, 1.0 mm gasket, 3 cc dish
Output
Static 11.32:1, dynamic 9.95:1
Taking 5 cc out of the piston dish adds three-quarters of a point. Builders aiming that high usually plan around 98 RON, and confirm on a dyno with knock monitoring.
Background and insight
Static compression ratio is (swept volume + clearance volume) / clearance volume. Swept volume is π/4 x bore² x stroke for one cylinder. Clearance volume is everything left above the piston at TDC: the chamber in the head, the cylinder of gasket (π/4 x gasket bore² x compressed thickness), the deck volume (π/4 x bore² x deck clearance), and the piston crown shape. In this calculator a dish or valve relief is entered as a positive volume because it adds space, and a dome as negative because it takes space away. A piston that rises above the deck at TDC has a negative deck clearance.
Dynamic compression accounts for the intake valve staying open after bottom dead centre. Until it closes, the rising piston pushes charge back into the port, so compression only really starts at intake valve closing (IVC). The calculator finds the piston position at a crank angle of 180° plus the IVC figure using slider-crank geometry, x = r + l − (r cos θ + √(l² − r² sin² θ)), where r is half the stroke and l the rod length, and uses the remaining travel as the effective stroke. Use the seat-to-seat (advertised) IVC from the cam card; a common rule of thumb is to add about 15° to the 0.050 in figure if that is all you have.
As rough guidance from engine builders, iron-headed street engines on premium pump fuel are usually kept near 8 to 8.5:1 dynamic, with aluminium heads tolerating a little more. These are rules of thumb, not limits: chamber shape, quench, ignition timing, fuel and boost all shift them.
Common use cases
Choosing heads, pistons and gaskets
Compare chamber sizes, gasket thicknesses and piston volumes to land on a target ratio before ordering parts.
Matching a camshaft
Check that the static ratio and the cam's intake closing give a dynamic ratio suited to the fuel you will run.
Rebuilding a stock engine
Work out what milling the heads or decking the block will do to compression after machining.
Boost planning
Pick a lower static ratio for a turbocharged or blown build and see how the parts choices get there.
Tips and limitations
- E10 is covered by the same petrol standard, with up to 10% ethanol. Check your owner's manual before using it in an older car.
- Measure chamber volume with a burette after any head machining. A skim to fix a warped head can add half a point.
- Raising compression or adding forced induction on a registered car is an engine modification. Ask your state registration authority whether it needs certification.
- Seat timing (advertised duration) gives a more realistic intake closing angle than the 0.050 in figure; as a rough rule of thumb, add about 15° to the latter if that is all the cam card shows, but use the cam card's seat-timing figure if it gives one.
Sources and further reading
- Fuel Quality Standards (Petrol) Determination 2024, Federal Register of Legislation. 91.0 and 95.0 RON minimums; up to 10% ethanol
- Internal Combustion Engines (course 2.61), MIT OpenCourseWare. Compression ratio and knock
Frequently asked questions
What octane is regular unleaded in Australia?
At least 91 RON. The Fuel Quality Standards (Petrol) Determination 2024 sets minimums of 91.0 RON for the 91 grade and 95.0 RON for the 95 grade. 98 is a premium product sold by fuel companies above those minimums.
Is Australian 98 the same as US 93?
Roughly. Australia labels fuel by research octane; US pumps show the average of research and motor octane, which is lower for the same fuel. US 91 to 93 sits in about the same range as Australian 95 to 98.
What compression ratio can I run on 98?
There is no single number. Chamber shape, quench, ignition timing, cam timing and boost all change the knock limit. Use the calculator to compare builds, then tune with knock monitoring.
How much does a thicker head gasket lower compression?
On the 92 mm bore six, going from a 1.0 mm to a 1.5 mm gasket adds 3.4 cc per cylinder and lowers the static ratio from 10.57 to 10.12:1.
Can I use E10 in a high-compression engine?
E10 is allowed up to 10% ethanol under the petrol standard and has a respectable octane rating, but compatibility depends on the vehicle. Follow the manufacturer's advice; the calculator does not model fuel.
Is there an in-depth guide to the Compression Ratio Calculator?
Yes. “Static vs Dynamic Compression Ratio: How to Calculate Both” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.