Australia version. Australian figures in kW and Nm, weights in kg, and a worked check against the NSW P1 and P2 high-performance vehicle rule of more than 130 kW per tonne. US version

Horsepower and kW Calculator (Australia)

Power in kW and hp from torque in Nm, flywheel versus dyno figures, and the NSW P-plate test of 130 kW per tonne of tare mass, with kg and km/h throughout.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Horsepower Calculator?

Australian car makers quote engine power in kilowatts and torque in newton metres, and that is the language this version uses. Enter torque and rpm and it gives kW, horsepower and PS, with an estimate of power at the wheels or at the flywheel when you have a dyno sheet.

The figure many Australians actually need is a power-to-weight ratio. In NSW, P1 and P2 drivers may not drive a high-performance vehicle, defined as one with a power to tare mass ratio over 130 kW per tonne. Transport for NSW uses the manufacturer's net engine power at the flywheel under the Australian Design Rules, rounded to the nearest kW, and the manufacturer's tare mass in tonnes, so a car with 183 kW and a 1,450 kg tare sits at 126.2 kW per tonne and is allowed.

A dyno sheet is not the test figure either. A chassis dyno reads at the wheels, after the gearbox and differential, while the test uses the manufacturer's tare and net power; modifications are covered by separate rules, and TfNSW can use other data if the manufacturer's figures no longer apply. Other states set their own probationary vehicle rules, so check yours.

  • Horsepower from torque in lb-ft or N·m and rpm, measured at the crank or the wheels
  • Quarter-mile power estimates from ET or trap speed with Hale, Fox and Huntington constants
  • Predicted ET and trap speed for a given power and weight
  • Crank and wheel horsepower with drivetrain loss presets, plus kW and PS
  • Side-by-side formula comparison, copy and share link
Read the guide: Estimating Horsepower from Quarter-Mile ET and Trap Speed

Updated

How to use the Horsepower Calculator

  1. Pick what you know: torque and rpm, quarter-mile ET, or trap speed.
  2. For torque, enter the value in lb-ft or N·m and the engine speed, and say whether it was measured at the crank or at the wheels.
  3. For a timeslip, enter race weight with the driver in lb or kg and the ET or trap speed, and choose a formula (Hale is the default).
  4. Pick a drivetrain type or type your own loss percentage.
  5. Read crank and wheel horsepower, kW and PS. With a weight entered, the calculator also predicts ET and trap speed for that power.

Worked examples

P-plate check: 350 Nm at 5,000 rpm, 1,450 kg tare

Input

Torque 350 N·m at 5,000 rpm, crank

Output

183.3 kW (245.8 hp); 183 / 1.450 = 126.2 kW per tonne

Under 130 kW per tonne, so not a high-performance vehicle on power-to-weight alone. Use the manufacturer's published power for the real test, not a torque-curve estimate.

Over the line: 400 Nm at 5,250 rpm, 1,600 kg tare

Input

Torque 400 N·m at 5,250 rpm, crank

Output

219.9 kW; 220 / 1.600 = 137.5 kW per tonne

Above 130 kW per tonne, so prohibited for P1 and P2 drivers in NSW.

From a chassis dyno sheet

Input

150 kW at the wheels, 15% drivetrain loss

Output

About 176.5 kW at the flywheel

Divide the wheel figure by 0.85, not multiply by 1.15. The loss is a rule of thumb that varies with the gearbox, tyres and dyno.

Background and insight

Horsepower is torque times rotational speed. In US units hp = lb-ft x rpm / 5,252.11, where 5,252.11 is 33,000 / 2π: James Watt's 33,000 ft·lbf per minute divided by the radians in one revolution. That is why torque and horsepower curves always cross at 5,252 rpm. One mechanical horsepower is 745.7 W; the metric horsepower (PS, CV or ch) is 735.5 W, so a figure in PS is about 1.4% larger than the same power in hp.

The quarter-mile formulas are empirical fits that relate power-to-weight to elapsed time and trap speed with a cube-root law: ET = C x (weight / hp)^(1/3) and trap mph = C x (hp / weight)^(1/3). The constants commonly attributed to Huntington (6.290 and 224), Fox (6.269 and 230) and Hale (5.825 and 234) come from different eras of cars and tyres, and the power they assume is net engine power at the clutch, with weight including the driver. Trap speed tracks power more closely than ET because it is less sensitive to the launch.

A chassis dyno measures at the wheels, so the reading is lower than the engine's rating by the losses in the gearbox, driveshafts, differential and tyres. Typical rules of thumb are 10 to 15% for a manual front or rear-wheel-drive car, more for automatics and all-wheel drive. To go from wheel to crank divide by (1 − loss); multiplying by (1 + loss) understates the crank figure.

Common use cases

  • Reading dyno sheets

    Turn a torque figure at a given rpm into horsepower, kW and PS, and estimate crank power from a chassis dyno run.

  • Drag strip estimates

    Get a power figure from a timeslip when you have no dyno, or predict what ET and trap speed a power upgrade should bring.

  • Comparing spec sheets

    Put European PS and kW ratings next to US horsepower on the same basis.

  • Power-to-weight planning

    See how much power, or weight saved, it takes to reach a target quarter-mile time.

Tips and limitations

  • To convert kW to hp, divide by 0.7457; 200 kW is 268 hp.
  • Tare mass is on the compliance plate or in the manufacturer's specifications; kerb weights in reviews are often different.
  • Peak torque and peak power come at different rpm, so torque times rpm at the torque peak is not the brochure power figure.

Sources and further reading

  1. Prohibited vehicle definitions, Transport for NSW. High-performance vehicle: power to tare mass ratio over 130 kW per tonne; power is ADR net engine power at the flywheel.
  2. Prohibited vehicles for P plate drivers, NSW Government

Frequently asked questions

What power-to-weight ratio can P-platers drive in NSW?

Up to 130 kW per tonne. A vehicle with a power to tare mass ratio greater than 130 kW per tonne is a high-performance vehicle and is prohibited for P1 and P2 drivers, along with vehicles with significant engine modifications.

How do I work out kW per tonne?

Divide the engine power in kW by the tare mass in tonnes. For 183 kW and 1,450 kg: 183 / 1.450 = 126.2 kW per tonne. Transport for NSW rounds power to the nearest kW and does not round the ratio.

How do I convert Nm to kW?

kW = Nm × rpm / 9,549. 350 Nm at 5,000 rpm is 183.3 kW. The calculator shows the same result in hp and PS.

Does a dyno reading count for P-plate rules?

No. The NSW rule uses the manufacturer's net engine power at the flywheel. A chassis dyno measures at the wheels, so its figure is lower and not the one used.

Why do Australian cars quote kW instead of horsepower?

Australia uses SI units, and the kilowatt is the SI unit of power. Horsepower still appears in conversation and imported marketing, so the calculator shows both.

Is there an in-depth guide to the Horsepower Calculator?

Yes. “Estimating Horsepower from Quarter-Mile ET and Trap Speed” covers the background, how it works, common pitfalls and worked examples. Read the full guide.