Australia version. Power in kW, pressure in bar and flow in cc/min by default, with Australian E85 (70 to 85% ethanol under the national standard) in mind. US version

Fuel Injector Size Calculator (kW)

Size fuel injectors for a kW target in cc/min with fuel pressure in bar, for petrol or E85, and check how much power your current injectors will support.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Fuel Injector Size Calculator?

Australian car makers, dyno sheets and the Australian Design Rules quote power in kilowatts, so this version starts in kW. Enter a target such as 300 kW at the crank for a turbocharged six, the injector count and maximum duty, and the pressure the injectors are rated at in bar. The calculator converts kW to horsepower for the BSFC formula, then returns flow per injector in cc/min and lb/hr.

E85 needs about 40% more fuel by mass (about 30% more volume) than petrol for the same power, and Australian E85 is not fixed at 85%: the Fuel Quality Standards (Ethanol E85) Determination 2024 allows anywhere from 70 to 85% ethanol by volume. A blend at the bottom of that range needs less fuel than the E85 preset assumes, so tuners running flex-fuel sensors size for the richest case and let the ECU trim.

  • Injector size from hp or kW, crank or wheel power
  • BSFC presets for naturally aspirated, blower and turbo engines on gasoline, E85 and methanol
  • lb/hr, cc/min and g/min with fuel specific gravity
  • Square-root pressure correction to the injector's rated pressure
  • Reverse mode: horsepower supported by a given injector
  • Common injector sizes and a shareable link
Read the guide: Fuel Injector Sizing: BSFC, Duty Cycle and Fuel Pressure

Updated

How to use the Fuel Injector Size Calculator

  1. Enter the target power in hp or kW and say whether it is at the crank or the wheels. For wheel power, set the drivetrain loss.
  2. Choose the induction type and fuel to load a typical BSFC, or type your own BSFC from dyno data.
  3. Set the number of injectors (usually one per cylinder) and the maximum duty cycle you are willing to run.
  4. Enter the pressure the injector is rated at and the fuel pressure it will see in use.
  5. Read the required flow per injector and the rating to buy, then use the second panel to check what a given injector size supports.

Worked examples

300 kW turbo six on 98

Input

300 kW at the crank, turbo BSFC 0.60, 6 injectors, 80% duty, rated and run at 3 bar

Output

402 hp; 50.3 lb/hr, 528 cc/min per injector; next common size 550 cc

300 kW is 402 hp. 402 x 0.60 = 241 lb/hr in total, shared by six injectors at no more than 80% duty.

Same engine on E85

Input

BSFC 0.84, E85, 3 bar; then rail at 4 bar

Output

682 cc/min per injector at 3 bar; 591 cc/min rated at 3 bar if run at 4 bar

Switching to E85 lifts the requirement by about 30% in volume here. Raising rail pressure to 4 bar lets a 650 cc injector cover it instead of a 750.

What six 1000 cc injectors support on E85

Input

6 x 1000 cc/min at 3 bar, E85 BSFC 0.84, 80% duty

Output

About 440 kW (590 hp) at the crank

The same injectors would support about 568 kW on petrol, which is why E85 conversions often go up a size.

Background and insight

BSFC is the mass of fuel an engine burns per unit of power per hour, in lb/hp·hr. A healthy naturally aspirated gasoline engine at full load uses about 0.45 to 0.50, an engine with a belt-driven blower 0.55 to 0.60 and a turbocharged engine 0.60 to 0.65, because boosted engines run richer and with more charge cooling from the fuel. Multiplying crank horsepower by BSFC gives the total fuel flow; dividing by the number of injectors and by the fraction of time each one may stay open (duty cycle) gives the flow each injector must deliver. Tuners keep peak duty at or below 80 to 85% so the injector has time to close and the fuel system has margin.

Alcohol fuels carry less energy per pound. E85 needs roughly 30 to 40% more fuel than gasoline for the same power (its stoichiometric air-fuel ratio is about 9.8 against 14.7), and methanol about twice as much (stoichiometric about 6.4). The calculator scales the gasoline BSFC by 1.4 for E85 and 2.2 for methanol. Injector ratings are usually given in lb/hr or cc/min at a stated pressure, often 3 bar (43.5 psi). The trade conversion of 10.5 cc/min per lb/hr assumes a fuel specific gravity of about 0.72; the calculator uses 0.72 for gasoline, 0.78 for E85 and 0.79 for methanol.

Injector flow follows the orifice law: it rises with the square root of the pressure difference across the injector. An injector rated at 43.5 psi flows √(58 ÷ 43.5) = 1.155 times as much at 58 psi. With a 1:1 rising-rate regulator the pressure difference stays constant under boost, so the base pressure is the one to enter. Real injectors depart from the square-root law at the extremes and their dead time changes with pressure and battery voltage, which is why tuners use the injector maker's characterisation data in the ECU.

Common use cases

  • Turbo and blower builds

    Size injectors before adding boost so the engine never runs lean at the top of the rev range.

  • E85 and flex-fuel conversions

    See how much bigger the injectors must be to make the same power on ethanol.

  • Checking an existing setup

    Find the power ceiling of stock or used injectors before a tune.

  • Engine swaps and EFI conversions

    Pick injectors for a carburettor-to-EFI kit or a swapped engine with a different cylinder count.

Tips and limitations

  • Australian E85 can be as low as 70% ethanol under the standard. A flex-fuel sensor lets the ECU follow the actual blend.
  • Engine modifications that raise power substantially or add forced induction may need certification under the National Code of Practice for Light Vehicle Construction and Modification (VSB 14) in your state. Check with your registration authority.
  • E85 is not sold everywhere in Australia. Check supply where you drive before converting.
  • Compare injector ratings at the same pressure; ratings are often quoted in cc/min at 3 bar (43.5 psi); check your injector's data sheet.

Sources and further reading

  1. Fuel Quality Standards (Ethanol E85) Determination 2024, Federal Register of Legislation. E85 must be 70 to 85% v/v ethanol
  2. Fuel Quality Standards (Petrol) Determination 2024, Federal Register of Legislation. 91 and 95 RON minimums; up to 10% ethanol
  3. Fuel Properties Comparison, US Department of Energy Alternative Fuels Data Center. Energy content of petrol and ethanol blends

Frequently asked questions

What size injectors do I need for 300 kW?

For a turbo six on petrol at 80% duty and 3 bar, about 528 cc/min each, so 550 cc injectors with little margin or 650 cc with more. On E85 it is about 682 cc/min, so 750 cc.

How do I convert kW to hp for injector sizing?

Multiply by 1.341 (1 hp is 745.7 W). The calculator does it for you when you choose kW: 300 kW becomes 402 hp.

How much ethanol is in Australian E85?

Between 70 and 85% by volume, under the Fuel Quality Standards (Ethanol E85) Determination 2024. The petrol and ethanol parts must each meet their own fuel standards.

Do I need engineering certification for bigger injectors?

Injectors on their own are part of a tune, but the power increase or forced induction they support may be a modification that needs certifying. Rules are set by each state under VSB 14, so ask your registration authority or a vehicle certifier.

Does E10 change injector size?

Very little. Up to 10% ethanol slightly raises fuel use for the same power, which the 80% duty margin covers.

Is there an in-depth guide to the Fuel Injector Size Calculator?

Yes. “Fuel Injector Sizing: BSFC, Duty Cycle and Fuel Pressure” covers the background, how it works, common pitfalls and worked examples. Read the full guide.