Australia version. Starts with a round poly rainwater tank in millimetres and litres, with guidance on tank size, weight, pumps and approvals from Sydney Water. US version

Rainwater Tank Volume Calculator (Australia)

Work out how many litres are in a round or slimline rainwater tank from the water level, the depth for a target volume and the weight of a full tank on its base.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Tank Volume Calculator?

In Australia the tank most people want to measure is a rainwater tank, and the usual question is how many litres are left when the level drops in a dry spell. The default is an upright round tank 1,850 mm across and 2,000 mm high inside, which holds 5,376 litres. With water 800 mm deep it has 2,150 litres, and because an upright cylinder has straight sides, 40% of the height is 40% of the volume.

Slimline tanks along a side fence are rectangular, so the same rule holds: a tank 2,000 by 700 by 1,800 mm holds 2,520 litres and every 100 mm of depth is 140 litres. The "depth for a volume" field turns that around, for example to mark the level at which a float switch should bring in mains top-up.

Size matters for more than storage. Sydney Water suggests that, if cost is a concern, you install a tank of at least 2,000 litres connected to 75% or more of the roof, notes that 1,000 litres of water weighs a tonne, and says tanks up to 10,000 litres do not normally need council approval in its area if conditions are met. The weight panel shows what the base has to carry.

  • Seven shapes: horizontal and vertical cylinder, rectangular, horizontal and vertical capsule, cone bottom and sphere
  • Filled volume, percent full and ullage at any depth
  • Depth for a target volume, solved numerically
  • Dip chart table and volume-depth chart at any step
  • Litres, m³, US and UK gallons, ft³ and oil barrels with exact conversions
Read the guide: Tank Volume Formulas and Dip Charts for Horizontal, Vertical and Odd Shapes

Updated

How to use the Tank Volume Calculator

  1. Pick the shape: vertical cylinder for a round tank, rectangular for a slimline, horizontal cylinder for a tank lying on its side.
  2. Enter inside dimensions in millimetres. For a corrugated or ribbed poly tank use the maker's capacity if it differs, because the ribs take some volume.
  3. Enter the water depth from the bottom. A tape down the inlet strainer or a clear tube on the outlet both work.
  4. Use the dip chart to mark a level stick or a sight tube, and the target field to find the depth for a volume you care about.

Worked examples

Round poly tank in a dry spell

Input

Vertical cylinder 1,850 mm diameter x 2,000 mm high, water 800 mm deep

Output

2,150 litres of 5,376 (40% full); 2,000 litres sits at 744 mm

In an upright tank litres rise evenly with depth, here 26.9 litres per 10 mm. Full, the water alone weighs about 5.4 tonnes, so the tank needs a level, compacted base.

Slimline tank down the side of the house

Input

Rectangular 2,000 x 700 x 1,800 mm, water 600 mm deep

Output

840 litres of 2,520 (33.3%); 1,000 litres at 714 mm

At 2,520 litres this meets the 2,000 litre minimum Sydney Water suggests for a budget installation. It still needs a pump to supply a toilet or washing machine at mains-like pressure.

Large rural or acreage tank

Input

Vertical cylinder 3,500 mm diameter x 2,400 mm high, water 1,000 mm deep

Output

23,091 litres capacity; 9,621 litres at 1 m (41.7%); 10,000 litres at 1,039 mm

This is above the 10,000 litre size that Sydney Water says does not normally need council approval, so check with your council and the NSW Housing Code, or your own state's rules, before buying.

Background and insight

A horizontal cylinder's partial volume is the area of a circular segment times the length: A = r² cos⁻¹((r − h)/r) − (r − h)√(2rh − h²). The same segment geometry, rotated, gives the spherical cap V = πh²(3r − h)/3 used for spheres and for the hemispherical ends of capsule tanks. A cone bottom fills as a smaller cone until the liquid reaches the cylinder.

Because the segment area is not linear in depth, rules of thumb mislead. At a quarter of the diameter a horizontal cylinder is 19.6% full, at half it is exactly 50% and at three quarters it is 80.4%. A sphere at a quarter of its height is only 15.6% full.

Unit factors are exact: 1 US gallon is 3.785411784 L, 1 imperial gallon 4.54609 L, and an oil barrel 42 US gallons (158.987 L). For custody transfer and tax purposes, tanks are calibrated by recognised strapping methods such as API MPMS Chapter 2 rather than from nominal drawings, because real tanks have dished heads, slopes, dents and internal fittings.

Common use cases

  • Fuel and oil inventory

    Turn a dipstick reading into litres or gallons for heating oil, diesel or lube tanks.

  • Water storage and rainwater tanks

    Find capacity and remaining days of supply from the water level.

  • Level gauge marking

    Get the depth for 25%, 50% or any volume to mark a sight glass or set level switches.

  • Process vessels and hoppers

    Volume in capsule and cone-bottom vessels at any fill, for batching and dosing.

Tips and limitations

  • Upright round and slimline tanks are proportional: half the height is half the volume. Only tanks lying on their side, and the domed top and bottom of some poly tanks, break that rule.
  • Plan for the weight. 1,000 litres of water is about a tonne, so a 5,000 litre tank puts about five tonnes on its base.
  • If you plumb tank water to toilets, the washing machine or a hot water system in NSW, the plumber must arrange an inspection, and you may need a backflow device and a mains top-up or automatic switch.
  • Connect as much roof as you can. Sydney Water notes that more roof area gives greater savings whatever the tank size.

Sources and further reading

  1. Rainwater tanks, Sydney Water. Sizing (at least 2,000 L to 75% of roof), weight (1,000 L is 1 tonne), approvals up to 10,000 L, pumps, inspections and backflow.
  2. Water Pressure Management Program, Sydney Water. Mains pressure in metres head, the pressure a tank pump has to match.
  3. Circular Segment, Wolfram MathWorld. The formula for a tank lying on its side.

Frequently asked questions

How many litres are in my round rainwater tank?

Multiply π x radius² x height in metres and multiply by 1,000 for litres. A tank 1,850 mm across and 2,000 mm high inside holds 5,376 litres. Enter the water depth instead of the height to see what is in it now.

What size rainwater tank should I get?

It depends on roof area, rainfall and what the water is used for. Sydney Water suggests at least 2,000 litres connected to 75% or more of the roof if budget is the constraint, and connecting the tank to at least one regularly used indoor fixture such as a toilet or washing machine.

Do I need council approval for a rainwater tank?

In Sydney Water's area, tanks up to 10,000 litres do not normally need council approval provided set conditions are met; check the NSW Housing Code and your council. Other states have their own rules, so ask your local council.

How heavy is a full rainwater tank?

Roughly one tonne per 1,000 litres of water, plus the tank itself. The calculator shows the weight of water when full; a 5,376 litre tank carries about 5.4 tonnes of water.

Do I need a pump on my rainwater tank?

Usually, if the water goes anywhere other than a garden tap. Sydney Water says most tanks need a pump to match drinking water pressure; a tank 2 m above a tap gives only about 20 kPa, far below mains supply. Use the Hydrostatic Pressure Calculator to check your own setup.

Is there an in-depth guide to the Tank Volume Calculator?

Yes. “Tank Volume Formulas and Dip Charts for Horizontal, Vertical and Odd Shapes” covers the background, how it works, common pitfalls and worked examples. Read the full guide.