Australia version. Opens on the 1/4" BSP parallel (G) pipe thread with metric drills, checks the BSP drills on an Australian supplier's chart, and covers BSW, BSF and metric coarse. US version
Tap Drill Size Calculator for BSP and Metric Threads
Tap drill sizes for BSP fittings, metric coarse bolts and BSW Whitworth threads in mm, with the real thread percentage of each chart drill so you can pick one.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Tap Drill Size Calculator?
This version opens on the 1/4" BSP parallel (G) pipe thread with metric drills. BSP uses the same 55° Whitworth form as BSW and BSF, not the 60° of metric and UNC, so the three share one thread system here with the Whitworth thread depth of 0.640327 × pitch. Metric coarse and fine, and UNC and UNF, are in the same calculator.
BSP is where charts get confusing, because the name is a pipe bore, not a diameter. G 1/4 measures 13.157 mm over the threads with 19 threads per inch. The AIMS Industrial chart, from an Australian tool supplier, lists 8.8 mm for 1/8" BSP, 11.8 mm for 1/4", 15.0 mm for 3/8" and 18.6 mm for 1/2". Run those through the calculator and they leave 79.9%, 79.3%, 97.1% and slightly over 100% of the thread depth: the bigger sizes are drilled almost to the minor diameter.
That spread is the decision to make. For a port in aluminium or a fitting in thin plate, more engagement holds better; in stainless or with a worn tap, a drill one step larger saves the tap and the job. Pick the size, read the percentage for each nearby drill and choose.
- Metric coarse and fine threads from M1.6 to M36 and UNC/UNF from #0 to 1-1/2 inch, plus custom threads
- British BSW, BSF and BSP (G) parallel threads with the Whitworth 55° formula
- Cutting and form tap formulas with any percent of thread
- Nearest metric, fractional, number or letter drill and the real thread percentage it gives
- Options table either side of the target, a full chart for the chosen series and a drill check field
- Formula panel, copy and share link; runs entirely in your browser
Updated
How to use the Tap Drill Size Calculator
- Under thread system pick "BSW / BSF / BSP" for pipe and Whitworth threads, "Metric (ISO)" for bolts, or "UNC / UNF" for imported machinery.
- Choose the size. BSP sizes are G (parallel) threads from 1/8" to 1".
- Set the percent of thread: 75% is the general figure; enter a chart drill in the check field to see what it really gives.
- Use the options table to pick a drill from the green band that you actually have in the drill stand.
Worked examples
1/4" BSP parallel port
Input
G 1/4 BSPP (19 TPI), 75% thread; check the 11.8 mm chart drill
Output
11.9 mm gives 73.4%; 11.8 mm gives 79.3%
Pitch 1.337 mm, basic minor diameter 11.445 mm. Parallel BSP ports seal with a bonded seal or O-ring at the face, so a little less engagement does not cause leaks.
1/2" BSP with the chart drill
Input
G 1/2 BSPP (14 TPI); check 18.6 mm and 19 mm
Output
18.6 mm gives over 100%; 19 mm gives 84.1%; the 75% answer is 19.2 mm
The 18.6 mm chart drill is a few hundredths under the 18.631 mm minor diameter, so the tap has to cut the bore as well as the thread. In steel a 19 mm drill is much easier on a 14 TPI tap.
M8 and M12 bolts
Input
Metric coarse, cutting tap, 75%; check 6.8 mm and 10.2 mm
Output
M8 x 1.25: 6.8 mm gives 73.9%. M12 x 1.75: 10.2 mm gives 79.2%, 10.3 mm gives 74.8%
The usual chart sizes (5.0, 6.8, 8.5 and 10.2 mm for M6 to M12) all land between about 74% and 79%.
3/8" BSW bolt
Input
3/8" BSW (16 TPI), 75%
Output
8 mm drill gives 75.0%
The pitch is 1.5875 mm and an 8 mm drill lands right on 75%, but tap it with a BSW tap: a 3/8-16 UNC tap has the same pitch and the wrong 60° angle.
Background and insight
The percent-of-thread convention measures how much of the basic thread depth the tapped hole leaves for the screw to bear on. For 60° unified and ISO metric threads the basic double height used for this purpose is 1.299 × pitch, so the cutting tap drill formula is drill = D − 0.01299 × %thread × P, with P in millimetres or as 1/TPI in inches. Machinery's Handbook gives this form and the inverse, %thread = (D − drill) / (0.01299 × P).
Tap makers commonly point out that a 75% thread is only a few percent weaker than a full thread in steel, because the bolt or the external thread usually fails first, yet a 100% thread takes roughly three times the torque to tap. That is why charts settle on 75% for general work, 60 to 65% for tough or work-hardening alloys, and higher only for thin sections where every bit of engagement counts.
Form taps do not cut; they push material into the thread shape, so the hole must be larger. Tap makers and Machinery's Handbook give drill = D − 0.0068 × %thread × P for forming, with 60 to 70% thread typical. A 1/4-20 form tap at 65% calls for 0.2279 in, which is a #1 drill. Always check the tap maker's chart, since some coatings and alloys move the ideal hole by a few hundredths of a millimetre.
Common use cases
Drilling and tapping on the shop floor
Find the tap drill when the chart drill is missing and see what the closest drill on the rack will give you.
Hard or gummy materials
Drop to 60 to 65% thread in stainless, titanium or Inconel to cut tapping torque and tap breakage.
Form tapping
Get the larger pilot hole a thread-forming tap needs in aluminium, copper and mild steel.
CAD and drawings
Pick a hole size for a tapped hole callout and record the thread engagement it produces.
Tips and limitations
- BSP and NPT are not interchangeable. NPT is a 60° taper thread from the US, and 1/4" NPT has 18 threads per inch against 19 for 1/4" BSP, so a mismatched pair binds after a turn or two.
- Parallel G threads seal at the face; tapered R threads (BSPT) seal on the thread with sealant and need their own drill and a taper tap.
- Drills cut a little oversize in steel, so the thread you get is usually a few percent under the figure shown.
- For blind holes, drill deep enough for the tap lead: about 3 to 5 pitches for a plug tap.
Sources and further reading
- Tapping drill size chart for thread cutting taps (metric and imperial equivalents), AIMS Industrial Supplies. Supplier chart: BSP tap drills (8.8, 11.8, 15.0, 18.6 mm) and metric coarse drills.
- Pipework: BSP threads, dcldesign code. Major and minor diameters and pitch of G (ISO 228) and R (ISO 7) threads.
- British Standard Whitworth, Wikipedia. The 55° form and depth 0.640327 × pitch; BSP to ISO 228 uses the Whitworth form.
Frequently asked questions
What size drill for a 1/4 BSP tap?
11.8 mm is the usual chart size and leaves 79.3% thread on a G 1/4 parallel thread. An 11.9 mm drill gives 73.4% and is easier in stainless.
What size drill for a 1/2 BSP tap?
Charts commonly give 18.6 mm, which is just under the 18.631 mm minor diameter and leaves a full thread. A 19 mm drill leaves 84.1% and makes tapping much easier; the 75% answer is 19.2 mm.
Can I use a BSP tap for an NPT fitting from imported gear?
No. NPT has a 60° thread angle and a taper, and the threads per inch differ at several sizes (18 for 1/4" NPT, 19 for 1/4" BSP). Even at 1/2", where both have 14, the angle and taper do not match. Use the matching tap or an adaptor.
What are the standard tap drills for metric bolts?
For coarse threads: M6 x 1 takes 5.0 mm (77.0%), M8 x 1.25 takes 6.8 mm (73.9%), M10 x 1.5 takes 8.5 mm (77.0%) and M12 x 1.75 takes 10.2 mm (79.2%).
Is BSP a Whitworth thread?
Yes in form. BSP to ISO 228 uses the 55° Whitworth thread form, so a BSP tap shares its flank angle and thread depth rule with BSW and BSF, though the pitches differ by size. The calculator covers BSW and BSF from 1/8" or 3/16" to 1" and BSP from 1/8" to 1".
Why do two tap drill charts give different sizes for the same BSP thread?
Each chart aims for its own thread depth. Some list 11.5 mm for 1/4" BSP (96.8% thread) and others 11.8 mm (79.3%). Both make a usable thread; the larger drill is easier on the tap.
Is there an in-depth guide to the Tap Drill Size Calculator?
Yes. “Tap Drill Sizes and Percent of Thread: Choosing the Right Hole” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.