United Kingdom version. Torque in Nm and weight in kg, power in bhp, kW and PS as UK brochures show it, and a worked check against the DVSA A2 motorcycle licence limits. US version

BHP Calculator (UK)

Convert torque in Nm at a given rpm to bhp, kW and PS, check a motorbike against the A2 licence limits of 35 kW and 0.2 kW per kg, and estimate power at the wheels.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Horsepower Calculator?

UK car and bike brochures quote power three ways: bhp, PS and kW. One PS is 735.5 W and one mechanical horsepower 745.7 W, so a figure in PS is about 1.4% larger than the same power in bhp. This version starts with torque in newton metres, the unit printed in UK specifications, and shows all three at once.

The units matter most for new motorcyclists. An A2 licence, from age 19, covers bikes up to 35 kW with a power-to-weight ratio no higher than 0.2 kW per kg, and a restricted bike must not be derived from one with more than twice that power. A bike making 37 Nm at 9,000 rpm produces 34.9 kW (46.8 bhp), just inside the limit, and it must weigh at least about 174 kg to stay within 0.2 kW per kg.

Rolling road results in the UK are often given at the wheels. Drivetrain losses sit between the flywheel figure the manufacturer quotes and the wheel figure the dyno sees, so enter where the reading was taken and the loss you expect.

  • Horsepower from torque in lb-ft or N·m and rpm, measured at the crank or the wheels
  • Quarter-mile power estimates from ET or trap speed with Hale, Fox and Huntington constants
  • Predicted ET and trap speed for a given power and weight
  • Crank and wheel horsepower with drivetrain loss presets, plus kW and PS
  • Side-by-side formula comparison, copy and share link
Read the guide: Estimating Horsepower from Quarter-Mile ET and Trap Speed

Updated

How to use the Horsepower Calculator

  1. Pick what you know: torque and rpm, quarter-mile ET, or trap speed.
  2. For torque, enter the value in lb-ft or N·m and the engine speed, and say whether it was measured at the crank or at the wheels.
  3. For a timeslip, enter race weight with the driver in lb or kg and the ET or trap speed, and choose a formula (Hale is the default).
  4. Pick a drivetrain type or type your own loss percentage.
  5. Read crank and wheel horsepower, kW and PS. With a weight entered, the calculator also predicts ET and trap speed for that power.

Worked examples

A2 check: 37 Nm at 9,000 rpm

Input

Torque 37 N·m at 9,000 rpm, at the crank

Output

34.87 kW; 46.76 hp; 47.41 PS

Under the 35 kW limit. At 0.2 kW per kg the bike needs a weight of at least 174.4 kg, which is why the rule catches some light, powerful bikes.

Just over: 46 Nm at 7,500 rpm

Input

Torque 46 N·m at 7,500 rpm

Output

36.13 kW; 48.45 hp

Over 35 kW, so this output is not A2-compliant without a restrictor. A restriction kit is only allowed when the full-power bike makes no more than 70 kW.

Hot hatch: 250 Nm at 5,500 rpm

Input

Torque 250 N·m at 5,500 rpm

Output

144.0 kW; 193.1 bhp; 195.8 PS

Peak torque and peak power rarely happen at the same rpm, so this is the power at that point on the curve, not necessarily the brochure peak.

Background and insight

Horsepower is torque times rotational speed. In US units hp = lb-ft x rpm / 5,252.11, where 5,252.11 is 33,000 / 2π: James Watt's 33,000 ft·lbf per minute divided by the radians in one revolution. That is why torque and horsepower curves always cross at 5,252 rpm. One mechanical horsepower is 745.7 W; the metric horsepower (PS, CV or ch) is 735.5 W, so a figure in PS is about 1.4% larger than the same power in hp.

The quarter-mile formulas are empirical fits that relate power-to-weight to elapsed time and trap speed with a cube-root law: ET = C x (weight / hp)^(1/3) and trap mph = C x (hp / weight)^(1/3). The constants commonly attributed to Huntington (6.290 and 224), Fox (6.269 and 230) and Hale (5.825 and 234) come from different eras of cars and tyres, and the power they assume is net engine power at the clutch, with weight including the driver. Trap speed tracks power more closely than ET because it is less sensitive to the launch.

A chassis dyno measures at the wheels, so the reading is lower than the engine's rating by the losses in the gearbox, driveshafts, differential and tyres. Typical rules of thumb are 10 to 15% for a manual front or rear-wheel-drive car, more for automatics and all-wheel drive. To go from wheel to crank divide by (1 − loss); multiplying by (1 + loss) understates the crank figure.

Common use cases

  • Reading dyno sheets

    Turn a torque figure at a given rpm into horsepower, kW and PS, and estimate crank power from a chassis dyno run.

  • Drag strip estimates

    Get a power figure from a timeslip when you have no dyno, or predict what ET and trap speed a power upgrade should bring.

  • Comparing spec sheets

    Put European PS and kW ratings next to US horsepower on the same basis.

  • Power-to-weight planning

    See how much power, or weight saved, it takes to reach a target quarter-mile time.

Tips and limitations

  • To convert PS to bhp, multiply by 0.986; to convert bhp to kW, multiply by 0.7457.
  • A wheel figure from a rolling road divided by (1 − loss) gives an estimate of flywheel power, not the other way round.

Sources and further reading

  1. Riding a motorcycle, moped or motor tricycle: bike categories, ages and licence requirements, GOV.UK (DVSA). A1 up to 11 kW and 0.1 kW/kg; A2 up to 35 kW, 0.2 kW/kg and not derived from more than twice its power.
  2. The Motor Vehicles (Driving Licences) (Amendment) Regulations 2012, Schedule 3, legislation.gov.uk. Legal definition of an A2 motorcycle.

Frequently asked questions

What is the difference between bhp and PS?

PS (Pferdestärke, metric horsepower) is 735.5 W and bhp is about 745.7 W, so 100 PS is 98.6 bhp. Many UK brochures list PS because European type-approval figures are in kW and PS.

How many bhp is the A2 licence limit?

The limit is 35 kW, which is 46.9 bhp or 47.6 PS. The bike must also stay within 0.2 kW per kg, and a restricted bike must not be derived from one with more than twice its power.

What can I ride on an A1 licence?

From 17, a light motorcycle up to 125 cc and 11 kW, with a power-to-weight ratio no higher than 0.1 kW per kg. Enter the torque and rpm to check the kW figure.

How do I calculate bhp from torque in Nm?

Power in kW is torque in Nm times rpm divided by 9,549. Divide by 0.7457 for bhp. The calculator converts Nm to lb-ft and uses the 5,252 constant, which gives the same answer.

Why is my rolling road figure lower than the brochure?

Most rolling roads measure power at the wheels, after losses in the gearbox, differential and tyres. Choose "Wheels (chassis dyno)" and a drivetrain loss to estimate the flywheel figure.

Is there an in-depth guide to the Horsepower Calculator?

Yes. “Estimating Horsepower from Quarter-Mile ET and Trap Speed” covers the background, how it works, common pitfalls and worked examples. Read the full guide.