United Kingdom version. Adds the BS EN 1993-1-1 clause 6.3.1 buckling resistance with the UK National Annex factor γM1 = 1.0, Eurocode buckling curves for UK section types, S355 and E = 210 GPa. US version
Column Buckling Calculator (UK, Eurocode 3)
Euler load plus the BS EN 1993-1-1 flexural buckling resistance Nb,Rd with the UK National Annex γM1, for cold-formed EN 10219 and hot-finished EN 10210 SHS and CHS.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Column Buckling Calculator?
A UK steel column is designed to BS EN 1993-1-1 with its UK National Annex. The Euler load is still the starting point, but the design resistance comes from clause 6.3.1: the non-dimensional slenderness λ̄, a buckling curve chosen from Table 6.2, the reduction factor χ and Nb,Rd = χ A fy / γM1, with γM1 = 1.0 in the UK. This version sets the design-code check to Eurocode 3 and lets you pick the section type that decides the curve.
The section type matters more than people expect. A 100 x 100 x 5 SHS in S355, pinned at both ends over 3.5 m, has λ̄ = 1.18. Made cold-formed to EN 10219 it sits on curve c and resists 299 kN; the same size hot-finished to EN 10210 sits on curve a and resists 366 kN, 22% more. Square and circular hollow sections look identical on a drawing, so check the product standard before you swap one for the other.
Section properties here come from the sharp-cornered shape, which overstates the area of a real hollow section slightly. For a final check, choose "Enter I and A directly" and type the Blue Book values.
- Euler critical load and stress with effective length KL and slenderness KL/r
- Six end conditions with theoretical and AISC recommended K values, or a custom K
- Johnson parabola below the transition slenderness, with a clear validity warning
- AISC 360-16 E3 cross-check with LRFD φPn and ASD Pn/Ω, or a design-code check to BS EN 1993-1-1 (UK NA), IS 800 or CSA S16
- Tube, bar, SHS and rectangle sections or your own I and A, SI and US units, column curve chart
Updated
How to use the Column Buckling Calculator
- Choose SI or US units, then pick the end conditions. The list shows the theoretical K and the AISC recommended design K for each.
- Select whether to use the design value, the theoretical value or a custom K, and enter the unbraced length L between lateral supports.
- Pick a material to fill in E and the yield strength, or type your own. Leave Fy blank for a pure Euler result.
- Describe the cross-section. For an I-beam or channel, enter the weak-axis I and the area from a section table, because the column buckles about the axis with the smallest I.
- Read the Euler load, slenderness, governing formula and allowable load, and check the AISC E3 values and the column curve.
Worked examples
100 x 100 x 5 SHS in S355, 3.5 m, pinned
Input
SHS 100 x 5 mm, K = 1.0, E 210 GPa, fy 355 MPa, Eurocode 3, cold-formed
Output
KL/r 90.1; λ̄ 1.18; curve c, χ 0.444; Nb,Rd 299 kN
Switch the section type to hot-finished and the curve becomes a, χ rises to 0.543 and Nb,Rd to 366 kN. Euler alone would suggest 485 kN, which is why the elastic load is never the design value.
114.3 x 5 CHS in S355, 3 m, pinned
Input
Round tube 114.3 x 5 mm, K = 1.0, E 210 GPa, fy 355 MPa
Output
KL/r 77.6; λ̄ 1.02; cold-formed 324 kN (curve c); hot-finished 399 kN (curve a)
A short, stocky column gains most from the better curve, because it buckles inelastically where imperfections and residual stresses matter most.
Background and insight
Leonhard Euler derived the critical load of an ideal pin-ended column in 1744: Pcr = π²EI/L². Other end conditions are handled by replacing L with an effective length KL, the distance between points of zero moment in the buckled shape. A column fixed at both ends buckles like a pinned column half as long (K = 0.5), a flagpole fixed at the base and free at the top like one twice as long (K = 2.0). Since the load varies with 1/K², end fixity changes capacity by a factor of up to sixteen.
Euler assumes the material stays elastic, so it is only valid when the critical stress Pcr/A is below the proportional limit. Real rolled and welded sections carry residual stresses from cooling, so yielding starts earlier; the classic structural stability texts (and the old AISC allowable stress method) put the limit at half the yield stress. Below the transition slenderness Cc = √(2π²E/Fy), J. B. Johnson's parabola, σcr = Fy − (Fy²/4π²E)(KL/r)², joins the Euler curve tangentially at Fy/2 and caps the stress at Fy for a stub column.
Modern steel codes use a single curve fitted to tests on columns with real out-of-straightness. AISC 360-16 Section E3 gives Fcr = 0.658^(Fy/Fe) Fy for KL/r up to 4.71√(E/Fy) and 0.877 Fe beyond, where Fe is the Euler stress, with φ = 0.90 for LRFD and Ω = 1.67 for ASD. The recommended K values (0.65, 0.80, 1.2, 1.0, 2.1 and 2.0) come from Commentary Table C-A-7.1.
Common use cases
Posts and pipe columns
Check a steel post, lally column or tube upright under a beam before choosing its size.
Struts, braces and push rods
Find the buckling load of a compression strut, linkage, actuator rod or truss member.
Machine and frame design
Size aluminium or steel frame legs and slender machine parts against elastic buckling.
Teaching stability
Show how K, length and section shape move a column along the Euler and Johnson curves.
Tips and limitations
- Table 6.2 puts hot-finished hollow sections on curve a (a0 for S460), cold-formed on curve c, rolled I-sections with h/b over 1.2 on curve b about the minor axis, and rolled H-sections (h/b ≤ 1.2) on curve b about the major axis and c about the minor axis.
- The UK National Annex sets γM1 = 1.0 for buildings; bridges use other values.
- Effective lengths are a matter of judgement in the Eurocode. The K values in the list are guides for near-ideal end conditions; a pinned base on a real baseplate is often taken as 1.0.
Sources and further reading
- Structure: Approved Document A, Ministry of Housing, Communities and Local Government. Statutory guidance on the structural requirements of the Building Regulations in England.
- Eurocode 3: Design of steel structures, European Commission Joint Research Centre. EN 1993-1-1 clause 6.3.1 flexural buckling, Tables 6.1 and 6.2.
- Universal beams: dimensions and properties (Blue Book), Steel for Life and the Steel Construction Institute. Section properties for UK sections designed to BS EN 1993-1-1 with the UK National Annex.
Frequently asked questions
How is column buckling resistance calculated to Eurocode 3?
Work out λ̄ = √(A fy / Ncr), then Φ = 0.5 [1 + α (λ̄ − 0.2) + λ̄²] and χ = 1 / (Φ + √(Φ² − λ̄²)). The design resistance is Nb,Rd = χ A fy / γM1. The calculator shows each value when the code check is set to BS EN 1993-1-1.
What is γM1 in the UK National Annex?
For buildings the UK National Annex to BS EN 1993-1-1 sets γM0 = γM1 = 1.0, so the buckling resistance is χ A fy with no further reduction.
Which buckling curve should I use for an SHS?
Hot-finished hollow sections to EN 10210 use curve a (α = 0.21) up to S420; cold-formed sections to EN 10219 use curve c (α = 0.49). The difference can be 20% or more in resistance at moderate slenderness.
Why does the calculator use E = 210 GPa?
BS EN 1993-1-1 gives E = 210,000 N/mm² for structural steel. That raises the Euler load by 5% compared with the 200 GPa many US tables use.
Is the Euler load safe to design with?
No. Euler assumes a perfectly straight, centrally loaded column with no residual stress. Real columns fail below it, which is what the buckling curves allow for.
Is there an in-depth guide to the Column Buckling Calculator?
Yes. “Column Buckling Explained: Euler, K Factors, Slenderness and the Johnson Parabola” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.