United Kingdom version. Tyre spelling, millimetre dimensions with speed in mph, and the UK legal rules on tread depth and suitable tyres from the Construction and Use Regulations. US version

Tyre Size Calculator (UK)

Compare two tyre sizes in millimetres, see the change in overall diameter and your true speed in mph against the speedometer, with the UK 1.6 mm tread rule.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Tire Size Calculator?

A UK tyre size such as 205/55 R16 tells you the section width in millimetres, the sidewall as a percentage of that width, and the wheel size in inches. This version shows the results in millimetres with speeds in mph, because that is how UK speedometers and speed limits work.

The common reason to compare sizes is a wheel change. Swapping 205/55 R16 for 225/40 R18 makes the tyre 5.3 mm taller overall (0.84%), so at an indicated 70 mph you are doing 70.6 mph. Going from 225/45 R17 to 215/60 R16 for a winter set adds 30.1 mm (4.75%), which takes you outside the usual 3% guideline: at an indicated 70 you would be doing 73.3 mph.

The law cares about the tyre as well as its size. Regulation 27 of the Road Vehicles (Construction and Use) Regulations 1986 makes it an offence to use a tyre that is unsuitable for the use or the tyres on the other wheels, and for cars it requires at least 1.6 mm of tread across the central three-quarters of the tread breadth. A non-standard size may also count as a modification, so ask your insurer before fitting one.

  • Parses metric (P, LT, ST, ZR) and flotation sizes
  • Diameter, sidewall, width, circumference and revs per mile and per km
  • Side-by-side comparison with differences in mm, inches and percent
  • Speedometer error table in mph or km/h
  • Scale drawing of both tires
  • Clear ±3% guideline check with an honest caveat
  • Shareable link and copy-ready summary
Read the guide: Fuel Costs, MPG and Tire Sizes: The Driving Maths Explained

Updated

How to use the Tire Size Calculator

  1. Enter your current tire size exactly as it appears on the sidewall, for example 225/45R17 91V.
  2. Optionally enter a new size to compare, or tap one of the common sizes below the boxes.
  3. Choose inches or millimetres for the measurements and mph or km/h for the speed table.
  4. Read the diameter difference and whether it falls within the ±3% guideline, then check the dimension table, the scale drawing and the speedometer table.
  5. Use Copy result or Share link to send the comparison to a tire shop or forum.

Worked examples

Upgrading from 16 to 18 inch alloys

Input

205/55R16 to 225/40R18

Output

631.9 mm to 637.2 mm overall (+5.3 mm, +0.84%); 70 mph indicated is 70.6 mph

The lower-profile tyre keeps the overall diameter close, so the speedometer barely moves. The sidewall drops from 112.75 mm to 90 mm, which means a firmer ride and more risk of kerbing the rim.

A winter set on smaller wheels

Input

225/45R17 to 215/60R16

Output

634.3 mm to 664.4 mm (+30.1 mm, +4.75%); 70 mph indicated is 73.3 mph

Outside the 3% guideline. A size such as 205/60R16 is +2.85% (18.1 mm), so 70 indicated is 72.0 mph. Check the handbook for the sizes the maker approves for your car.

A wider tyre on the same wheel

Input

205/55R16 to 215/55R16

Output

631.9 mm to 642.9 mm (+11 mm, +1.74%); 30 mph indicated is about 30.5 mph

A wider tyre with the same aspect ratio also has a taller sidewall. In a 30 mph zone the speedometer reads about half a mile an hour low, which matters near a camera.

Background and insight

A metric tire size has three numbers. The first is section width in millimetres. The second is the aspect ratio, the sidewall height as a percentage of that width. The letter is the construction (R for radial) and the last number is the wheel diameter in inches. So 225/45R17 is 225 mm wide with a sidewall of 225 x 0.45 = 101.25 mm on a 17 inch wheel. Overall diameter is the wheel plus two sidewalls: 17 x 25.4 + 2 x 101.25 = 634.3 mm, or 24.97 inches.

Flotation sizes state the overall dimensions in inches directly: 33x12.50R15 is 33 inches tall and 12.5 inches wide on a 15 inch wheel, which leaves a 9 inch sidewall. Revolutions per mile follow from the circumference: one mile (1,609,344 mm) divided by pi x diameter. For 225/45R17 that is about 808.

When changing sizes, the widely repeated rule of thumb in the tire trade is to stay within about 3% of the original overall diameter, so the speedometer, ABS, stability control and gearing stay close to how the car was calibrated. It is a guideline, not a law or a manufacturer approval. Load index, speed rating, rim width and clearance to suspension and bodywork matter just as much, and the sizes on your door-jamb placard are the ones the maker has tested.

Common use cases

  • Choosing new wheels

    Find a tire size for a larger or smaller wheel that keeps overall diameter close to stock.

  • Lifted trucks and off-roaders

    See how much taller a flotation or LT size is and how far the speedometer will be off.

  • Winter tire sets

    Check that a narrower winter size on smaller wheels stays within the guideline.

  • Speedometer correction

    Work out your true speed, or the correction factor a programmer or GPS check should show.

  • Decoding a sidewall

    Understand what the numbers on a used tire or a listing actually mean in inches and millimetres.

Tips and limitations

  • The legal minimum for cars is 1.6 mm across the central three-quarters of the tread. It is a legal floor, not a replacement target, so check the tread with a gauge as it gets close.
  • Keep the same size and type of tyre across an axle; mixing types can make a tyre unsuitable under regulation 27.
  • Read the load index and speed rating as well as the size: a replacement should meet the figures in your handbook.
  • Ask your insurer before fitting non-standard wheel or tyre sizes; many policies ask you to declare modifications.

Sources and further reading

  1. The Road Vehicles (Construction and Use) Regulations 1986, regulation 27, legislation.gov.uk. Unsuitable tyres, mixing with tyres on other wheels, and the 1.6 mm tread rule for cars in 27(4)(f).
  2. ETRTO Standards Manual, European Tyre and Rim Technical Organisation. The metric size designation (width/aspect ratio, rim diameter) used on tyres sold in the UK.

Frequently asked questions

What is the legal tyre tread depth in the UK?

For cars and light vans and trailers, at least 1.6 mm throughout a continuous band across the central three-quarters of the tread breadth and around the whole tyre, under regulation 27(4)(f) of the Road Vehicles (Construction and Use) Regulations 1986.

Can I fit a different tyre size from the one on my car?

Yes, if it fits without rubbing, carries the right load and speed ratings and is suitable for the car. Keep the overall diameter within about 3% so the speedometer and ABS stay close to calibration, and check the sizes listed in your handbook.

Will bigger tyres make my speedometer wrong?

A taller tyre covers more road per turn, so you go faster than the speedometer shows. On 215/60R16 instead of 225/45R17 the tyre is 4.75% taller, so 70 mph on the dial is 73.3 mph on the road.

Do I need to tell my insurer about different size tyres?

Ask before you buy. Many insurers count non-standard wheels and tyre sizes as modifications that must be declared, and the policy wording decides what happens if one is not.

What does 205/55 R16 91V mean on a UK tyre?

205 is the width in mm, 55 the sidewall as a percentage of the width (112.75 mm), R radial, 16 the wheel diameter in inches, 91 the load index and V the speed rating. The tyre is 631.9 mm tall and turns about 504 times per km.

Is there an in-depth guide to the Tire Size Calculator?

Yes. “Fuel Costs, MPG and Tire Sizes: The Driving Maths Explained” covers the background, how it works, common pitfalls and worked examples. Read the full guide.