India version. Adds property class 4.6 next to the HT classes, shows torque in Nm or kgf·m, and explains where IS 3757 structural bolts need their own tightening method. US version
Bolt Torque Chart Calculator (MS and HT Bolts)
Tightening torque in Nm or kgf·m for M3 to M36 bolts in property class 4.6, 8.8 and 10.9 (IS 1367 Part 3 / ISO 898-1), with a full torque chart and nut factors.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Bolt Torque Calculator?
On Indian shop floors and sites bolts are usually ordered as "MS bolts" or "HT bolts". The words are trade shorthand; the strength is the property class stamped on the head. Indian Standard IS 1367 (Part 3) sets the mechanical properties and tests for these classes (its 2002 edition is identical with ISO 898-1:1999), and BIS cites it for the proof-load, tensile and hardness tests on IS 3757 structural bolts. The proof stresses used here (225 MPa for 4.6, 580 MPa for 8.8 up to M16, 830 MPa for 10.9) are the ones in its Table 3.
The difference in torque is large. An M16 bolt loaded to 75% of its proof load with dry threads needs 84.6 N·m in class 4.6 and 218.1 N·m in class 8.8. Using an HT torque chart on MS bolts is a common way to strip threads or neck the bolt, so check the head marking first and select the class in the calculator.
Some torque wrenches and service manuals, older ones especially, still give torque in kgf·m alongside or instead of N·m. Pick kgf·m in the torque unit list to enter or read values that way; 1 kgf·m is 9.80665 N·m, so 88 N·m is 8.97 kgf·m.
- Metric coarse M3 to M36, UNC and UNF 1/4 to 1-1/2 inch
- ISO 898-1 classes 4.6, 5.6, 8.8, 10.9, 12.9 and SAE J429 Grades 5 and 8 with size-dependent proof stress
- Nut factor presets from Shigley Table 8-15, or a custom K
- Torque from target preload, or preload from a torque; percent of proof and yield shown
- Full torque chart for the series, copy and share link
Updated
How to use the Bolt Torque Calculator
- Pick the thread series: metric coarse, UNC or UNF. The grade list switches between ISO property classes and SAE grades.
- Choose the size and the property class or grade marked on the bolt head.
- Set the thread condition. Use dry, finish unknown (K = 0.20) if you are unsure, or enter a measured K.
- Choose Torque for a target preload and enter the percentage of proof load, or Preload from a torque and enter the wrench setting.
- Read the torque, preload and bolt stress, and use the chart below for other sizes at the same settings.
Worked examples
M16 class 4.6 against class 8.8
Input
M16 x 2, dry (K = 0.20), 75% of proof load
Output
Class 4.6: preload 26.4 kN, 84.6 N·m (8.63 kgf·m). Class 8.8: preload 68.2 kN, 218.1 N·m (22.24 kgf·m)
Both bolts have a 156.7 mm² stress area; only the proof stress changes, from 225 MPa to 580 MPa. That is why one chart cannot serve both.
Torque wrench set to 8 kgf·m on an M12 8.8 bolt
Input
Preload from a torque: 8 kgf·m (78.45 N·m), M12 x 1.75, class 8.8, K = 0.20
Output
Preload 32.7 kN; 66.9% of proof load; bolt stress 388 MPa
A round 8 kgf·m setting lands a little under the usual 75% target (88.0 N·m or 8.97 kgf·m). Enter the wrench setting in kgf·m and read the clamp force directly.
M12 class 10.9, oiled
Input
M12 x 1.75, class 10.9, lubricated (K = 0.18), 75% of proof
Output
Preload 52.5 kN; 113.3 N·m (11.55 kgf·m)
Typical of a machine or press assembly using 10.9 socket head cap screws. Oil lowers the torque for the same clamp force.
Background and insight
Proof load is the tensile force a bolt must carry without permanent set, and it is the usual basis for preload. It is the tensile stress area times the proof stress. ISO 898-1 gives proof stresses of 580 MPa for class 8.8 up to M16 (600 MPa above), 830 MPa for 10.9 and 970 MPa for 12.9. SAE J429 gives 85 ksi for Grade 5 from 1/4 to 1 inch (74 ksi from over 1 to 1-1/2 inch) and 120 ksi for Grade 8. Stress areas come from the thread geometry: As = π/4 (d − 0.9382P)² for ISO metric threads and At = 0.7854 (D − 0.9743/n)² for Unified threads in ASME B1.1, which reproduce the tabulated 58.0 mm² for M10 and 0.1419 in² for 1/2-13.
The nut factor K is not a friction coefficient; it lumps thread friction, underhead friction and thread geometry into one empirical number. Shigley's Mechanical Engineering Design (Table 8-15, from Bowman's Fastener Facts) lists 0.30 for non-plated black finish, 0.20 for zinc-plated, 0.18 for lubricated, 0.16 for cadmium-plated and 0.12 with anti-seize compound, and suggests K = 0.20 when the condition is unknown. Shigley recommends preload of 75% of proof load for connections that will be reused and 90% for permanent ones.
Because friction varies, torque is an imprecise way to set preload. Two bolts tightened to the same torque can differ in clamp force by 25% or more. Where that matters, engineers use turn-of-nut, direct tension indicators, ultrasonic measurement or torque-angle methods, and VDI 2230 for a full joint analysis.
Common use cases
Machine assembly
Set wrench values for flanges, brackets and covers when the drawing gives a bolt grade but no torque.
Automotive and equipment repair
Check whether a torque from a manual is in a sensible range for the bolt size and grade fitted.
Writing a torque table
Generate a chart for a whole thread series at the lubrication and preload your shop actually uses.
Diagnosing loose or broken bolts
Back out the preload a given torque produced to see whether a joint was under- or over-tightened.
Tips and limitations
- Read the head: a BIS-marked bolt carries its property class (4.6, 8.8, 10.9). Treat an unmarked bolt as unknown strength: do not use it in a structural or safety-critical joint. Class 4.6 is the lowest class the calculator offers, not a guaranteed minimum.
- For HSFG (high-strength friction grip) bolts to IS 3757 in steel structures, the bolt tension and tightening method come from IS 4000:1992, the code of practice for high strength bolts in steel structures, and the project specification, not from a general torque chart. Use the calculator only to understand the numbers.
- Galvanised bolts and those with thread-locking compound behave differently from plain oiled bolts; if the supplier gives a K value or torque, use it.
- Keep torque wrenches calibrated. A wrench reading high leaves every bolt in the joint under-tightened.
Sources and further reading
- Product Manual for High Strength Structural Bolts according to IS 3757: 1985, Bureau of Indian Standards. Property classes 8.8 and 10.9, sizes M16 to M36, for BIS-certified structural bolts; proof-load, tensile and hardness tests to IS 1367 (Part 3).
- IS 1367 (Part 3):2002 Technical supply conditions for threaded steel fasteners, Part 3: Mechanical properties of fasteners made of carbon steel and alloy steel, bolts, screws and studs, Bureau of Indian Standards (Public.Resource.Org copy). Identical with ISO 898-1:1999; Table 3 proof stresses by property class.
- IS 4000:1992 Code of practice for high strength bolts in steel structures, Bureau of Indian Standards (Public.Resource.Org copy). Covers joints with IS 3757 bolts; Table 3 minimum bolt tension; part-turn and direct tension indication methods.
- ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel, Part 1, International Organization for Standardization. Proof stresses by property class; adopted in India as IS 1367 (Part 3).
- Fastener Design Manual (NASA RP-1228), NASA. Torque, friction and preload scatter.
Frequently asked questions
What is the torque for an M16 HT bolt?
For an M16 class 8.8 bolt with dry threads at 75% of proof load, about 218 N·m (22.2 kgf·m), giving 68.2 kN of clamp force. A class 10.9 bolt of the same size takes more. Change the class in the calculator to see it.
What is the difference between MS bolts and HT bolts?
MS and HT are shop names, not classes in the standard, so read the property class on the head. Under IS 1367 (Part 3) class 4.6 has a proof stress of 225 MPa, class 8.8 has 580 to 600 MPa and class 10.9 has 830 MPa. For the same size an 8.8 bolt can carry about 2.6 times the clamp force of a 4.6 bolt.
How do I convert bolt torque from kgf·m to N·m?
Multiply by 9.80665. So 10 kgf·m is 98.1 N·m and 5 kgf·m is 49.0 N·m. The calculator converts both ways when you change the unit.
Which Indian Standard covers bolt property classes?
IS 1367 (Part 3) sets the mechanical properties of carbon and alloy steel bolts, screws and studs by property class, using the same classes as ISO 898-1 (its 2002 edition is identical with ISO 898-1:1999). High-strength structural bolts are covered by IS 3757 in classes 8.8 and 10.9, sizes M16 to M36.
Can I use this torque chart for HSFG bolts in a steel structure?
Not as the tightening specification. IS 4000:1992 is the code of practice for joints using IS 3757 bolts; it tabulates the minimum bolt tension (147 kN for an M20 class 8.8 bolt) and tensions bolts by the part-turn method or direct tension indication. Torque control alone has wide scatter, which is why structural codes specify controlled methods.
Should bolts be torqued dry or with oil?
Use the condition the torque value was written for. With oil (K = 0.18) an M12 8.8 bolt reaches the same 36.7 kN preload at 79.2 N·m instead of 88.0 N·m dry, so a dry value applied to oiled threads overloads the bolt.
Is there an in-depth guide to the Bolt Torque Calculator?
Yes. “Bolt Tightening Torque and Preload: T = KFd in Practice” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.