India version. Covers the British threads taught alongside metric taps in Indian ITI workshops: BSW, BSF and BSP pipe threads on the 55° Whitworth form, with mm drills and full working. US version
Tap Drill Size Calculator for BSW, BSP and Metric
Tap drill size for BSW, BSF and BSP threads and metric coarse taps, with the D − 1.28P working for Whitworth and the thread percentage each drill gives.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Tap Drill Size Calculator?
Indian ITI workshops teach British and metric taps side by side. The ITI Fitter curriculum from the Directorate General of Training lists taps of the British standard (B.S.W., B.S.F., B.A. and B.S.P.) and metric/BIS coarse and fine series, with "determination of tap drill size" as a topic, and its tool list for a workshop includes a Whitworth tap and die set, metric taps of 5, 6, 8, 10 and 12 mm, and a BSP pipe die set. This version handles all of those except BA.
Whitworth threads have a 55° angle and a thread depth of 0.640327 × pitch on each side, so the full depth on diameter is 1.28 × pitch, not the 1.299 × pitch of a 60° metric thread. For 1/4" BSW with 20 threads per inch the pitch is 25.4 / 20 = 1.27 mm, the minor diameter is 6.35 − 1.28 × 1.27 = 4.724 mm, and the tap drill for 75% thread is 6.35 − 0.0128 × 75 × 1.27 = 5.13 mm. A 5.1 mm drill gives 76.9%.
BSP pipe threads, which the same curriculum covers under pipe fitting, use the same 55° form but their size is a nominal bore. A 1/2" BSP thread has a major diameter of 20.955 mm, so you cannot get its drill from the name. The calculator holds the ISO 228-1 diameters, shows the steps it uses and lists a full chart for the series.
- Metric coarse and fine threads from M1.6 to M36 and UNC/UNF from #0 to 1-1/2 inch, plus custom threads
- British BSW, BSF and BSP (G) parallel threads with the Whitworth 55° formula
- Cutting and form tap formulas with any percent of thread
- Nearest metric, fractional, number or letter drill and the real thread percentage it gives
- Options table either side of the target, a full chart for the chosen series and a drill check field
- Formula panel, copy and share link; runs entirely in your browser
Updated
How to use the Tap Drill Size Calculator
- Choose "BSW / BSF / BSP" for British threads or "Metric (ISO)" for M-series taps. Whitworth threads use a cutting tap only.
- Pick the size from the list. BSW and BSF run from 1/8" or 3/16" to 1"; BSP from 1/8" to 1".
- Keep 75% thread for general fitting work; go to 65 to 70% in hard steel if the tap is tight.
- Read the nearest mm drill and its thread percentage, then open the calculation steps to see the formula worked through.
- Enter the drill you have in the check box to see if it will do.
Worked examples
1/4" BSW with a Whitworth hand tap set
Input
1/4" BSW (20 TPI), 75% thread, mm drills
Output
Theoretical 5.130 mm; 5.1 mm drill gives 76.9%; minor diameter 4.724 mm
P = 25.4 / 20 = 1.27 mm. d = 6.35 − 0.01280654 × 75 × 1.27 = 5.130 mm. The nearest drill in a 0.1 mm step set is 5.1 mm.
3/8" BSW on a mild steel flat
Input
3/8" BSW (16 TPI), 75% thread
Output
8 mm drill gives 75.0%
P = 1.5875 mm and the target is 8.000 mm, so a standard 8 mm drill lands almost exactly on 75%.
1/2" BSP socket for a pipe fitting
Input
G 1/2 BSPP (14 TPI); check 19 mm
Output
Theoretical 19.212 mm; 19 mm drill gives 84.1%
Major diameter 20.955 mm and pitch 1.814 mm. Pipe-thread charts usually work closer to full depth than bolt charts, so 19 mm (84%) is a sensible choice; 18.6 mm would be under the 18.631 mm minor diameter.
M10 and M12 from the metric tap set
Input
M10 x 1.5 and M12 x 1.75, cutting tap, 75%
Output
M10: 8.5 mm gives 77.0%. M12: 10.3 mm gives 74.8%, 10.2 mm gives 79.2%
For metric coarse threads "major diameter minus pitch" gives the same 8.5 mm and 10.25 mm, so either 10.2 or 10.3 mm works for M12.
Background and insight
The percent-of-thread convention measures how much of the basic thread depth the tapped hole leaves for the screw to bear on. For 60° unified and ISO metric threads the basic double height used for this purpose is 1.299 × pitch, so the cutting tap drill formula is drill = D − 0.01299 × %thread × P, with P in millimetres or as 1/TPI in inches. Machinery's Handbook gives this form and the inverse, %thread = (D − drill) / (0.01299 × P).
Tap makers commonly point out that a 75% thread is only a few percent weaker than a full thread in steel, because the bolt or the external thread usually fails first, yet a 100% thread takes roughly three times the torque to tap. That is why charts settle on 75% for general work, 60 to 65% for tough or work-hardening alloys, and higher only for thin sections where every bit of engagement counts.
Form taps do not cut; they push material into the thread shape, so the hole must be larger. Tap makers and Machinery's Handbook give drill = D − 0.0068 × %thread × P for forming, with 60 to 70% thread typical. A 1/4-20 form tap at 65% calls for 0.2279 in, which is a #1 drill. Always check the tap maker's chart, since some coatings and alloys move the ideal hole by a few hundredths of a millimetre.
Common use cases
Drilling and tapping on the shop floor
Find the tap drill when the chart drill is missing and see what the closest drill on the rack will give you.
Hard or gummy materials
Drop to 60 to 65% thread in stainless, titanium or Inconel to cut tapping torque and tap breakage.
Form tapping
Get the larger pilot hole a thread-forming tap needs in aluminium, copper and mild steel.
CAD and drawings
Pick a hole size for a tapped hole callout and record the thread engagement it produces.
Tips and limitations
- Check the pitch with a screw pitch gauge before choosing a tap: 1/4" BSW is 20 TPI, 1/4" BSF is 26 TPI and M6 is 1 mm pitch, and they look alike by eye.
- A BSW bolt will not seat properly in a 60° metric or UNC thread even when the pitch matches, because the flank angles differ.
- BSP parallel threads (G) seal with a washer or packing at the face. Tapered BSPT threads seal on the thread and need a taper tap and their own drill size.
- BA threads (47.5°) appear in the ITI syllabus but are not in this calculator.
Sources and further reading
- Competency based curriculum: Fitter (CTS, NSQF level 4), Directorate General of Training, Ministry of Skill Development and Entrepreneurship. Taps of British standard (BSW, BSF, BA, BSP) and metric/BIS series, determination of tap drill size, Whitworth tap set and BSP pipe die set in the tool list.
- Whitworth coarse thread (BSW, BS 84), gewinde-normen.de. Threads per inch and major diameters for BSW; 55° flank angle.
- Pipework: BSP threads, dcldesign code. Major and minor diameters and pitches of G (ISO 228) and R (ISO 7) pipe threads.
- British Standard Whitworth, Wikipedia. Thread depth 0.640327 × pitch and the 55° angle.
Frequently asked questions
What is the tap drill size for 1/4 BSW?
5.1 mm, which gives 76.9% thread. The exact 75% figure is 5.13 mm. A 5.2 mm drill leaves about 71%, still usable and easier to tap in hard steel.
What is the formula for tap drill size of a BSW thread?
Tap drill = D − 0.0128 × %thread × P, where P = 25.4 / TPI in mm. At 100% it gives the minor diameter D − 1.2807 × P. For 1/4" BSW: 6.35 − 1.2807 × 1.27 = 4.724 mm minor diameter, and 5.13 mm at 75%.
Why does a metric tap drill formula give a slightly different answer for BSW?
Metric threads are 60° with a full depth of 1.299 × P on diameter; Whitworth is 55° with 1.2807 × P. For 1/4" BSW the 60° formula gives 5.113 mm against 5.130 mm, so the drill rarely changes, but the thread form does, which is why BSW needs its own tap.
What drill size for a 1/2 inch BSP thread?
A 19 mm drill gives 84.1% of a G 1/2 parallel thread. The 75% answer is 19.2 mm. Pipe threads have no relation between the name and the diameter: 1/2" BSP is 20.955 mm across the threads.
Which tap drills do I need for the 5, 6, 8, 10 and 12 mm metric taps?
For coarse threads at about 75%: M5 x 0.8 takes 4.2 mm (77.0%), M6 x 1 takes 5.0 mm (77.0%), M8 x 1.25 takes 6.8 mm (73.9%), M10 x 1.5 takes 8.5 mm (77.0%) and M12 x 1.75 takes 10.2 mm (79.2%) or 10.3 mm (74.8%).
Is BSF the same as BSW?
Same 55° form, finer pitch. 1/4" BSF has 26 threads per inch against 20 for BSW, so its tap drill is larger: 5.4 mm at 75.9%.
Is there an in-depth guide to the Tap Drill Size Calculator?
Yes. “Tap Drill Sizes and Percent of Thread: Choosing the Right Hole” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.