India version. Metric, opening on a 2 mm MS bend 2440 mm long (an 8 ft sheet), with SWG thicknesses, IS 2062 E250 plate and the power press schedule of the Model Rules framed under the Factories Act. US version
Press Brake Tonnage Calculator (Tonnes, MS Sheet)
Bending force in tonnes for MS, GI and stainless sheet in mm or SWG, for an 8 ft bend or any length, with V-die rules, Indian plate grades and power press rules.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Press Brake Tonnage Calculator?
Most Indian fabrication shops bend MS and GI sheet in 8 ft lengths on press brakes rated in tonnes. This version starts there: a 2 mm MS sheet bent along its full 2440 mm in a 16 mm die needs about 41.1 tonnes, 16.9 tonnes per metre. The answer tells you at once whether the job suits a smaller brake or needs the bigger machine.
Thickness can come straight from a gauge. 18 SWG is 1.219 mm, and the same 2440 mm bend in a 10 mm die needs about 24.5 tonnes. For plate, work in mm and use the tensile strength from the mill test certificate: for structural plate to IS 2062, grade E250 has a minimum tensile strength of 410 N/mm² and E350 has 490 N/mm².
The tonnage is half of the check. Schedule VI of the Model Rules framed under the Factories Act, 1948 treats a press brake as a power press, calls for a thorough examination and test by a competent person at least once every 12 months, and lets only appointed people set its tools. The Occupational Safety, Health and Working Conditions Code, 2020 repeals the Factories Act from the date the Central Government notifies, and keeps rules made under the old Act in force, where they do not conflict with the Code, until they are repealed. Ask your state's Inspector of Factories which power press rules apply to your works.
- Air bending, bottoming and coining force
- US tons, metric tonnes and kN, per length and in total
- Material presets by tensile strength or custom UTS
- Inside radius and minimum flange rules for the chosen die
- Die opening comparison table and press capacity check
Updated
How to use the Press Brake Tonnage Calculator
- Keep metric units and enter the sheet thickness (for gauges, use the mm value: 16 SWG = 1.626 mm, 18 SWG = 1.219 mm).
- Enter the bend length; a full 8 ft sheet is 2440 mm.
- Use the 8 x T die rule or switch to "My die" for the die you have.
- Pick mild steel for MS, or choose custom tensile strength and enter the value from the test certificate.
- Enter your press capacity in tonnes to see the load as a percentage.
Worked examples
2 mm MS, full 8 ft bend
Input
T 2 mm, V 16 mm (8 x T), 2,440 mm, mild steel 414 N/mm², air bending
Output
41.13 t total (403.4 kN), 16.86 t/m
Comfortable on a 63 or 100 tonne brake. Bottoming the same bend would need about five times the force, which is why air bending is the normal choice.
18 SWG GI, 2440 mm
Input
T 1.219 mm (18 SWG), V 10 mm, 2,440 mm, mild steel base
Output
24.46 t total, 10.02 t/m
Typical of ducting and panel work. The zinc coating does not change the force meaningfully; the steel base does the work.
5 mm IS 2062 E250 plate, 3 m bend
Input
T 5 mm, V 40 mm, 3,000 mm, UTS 410 N/mm² (E250 minimum)
Output
125.2 t total (1,228 kN), 41.74 t/m
Too much for a 100 tonne brake over the full length. A 50 mm die would bring it down by a fifth at the cost of a larger inside radius.
8 mm plate, 2.5 m bend, 63 mm die
Input
T 8 mm, V 63 mm, 2,500 mm, UTS 410 N/mm²
Output
169.6 t total, 67.84 t/m
Check the punch and die rating in tonnes per metre as well as the press; heavy plate often hits the tooling limit first.
Background and insight
The working formula in tooling catalogues and press makers’ charts is tons per foot = 575 x T² / V, with T and V in inches, for a 90° air bend in mild steel of 60,000 psi tensile strength (AISI 1035 cold-rolled is the usual baseline). Force rises with the square of thickness, because both the bending moment and the section that resists it scale with T, and falls with the die opening, because a wider die gives the punch more leverage. Other materials are scaled by their tensile strength divided by 60 ksi.
In metric units the same relation is about 1.6 x UTS x T² / V in kN per metre, with UTS in MPa and T and V in millimetres. European and Asian brake makers often publish a version with a constant of 1.42 and a 450 MPa baseline, which gives a few percent less; both are rules of thumb for 90° bends and should be checked against the chart for your press.
Air bending touches the sheet at only three points, so the force is low and the radius is set by the die, roughly 15 to 17% of V in mild steel, 20 to 22% in 304 stainless and 13 to 15% in 5052-H32 aluminium (Steve Benson’s 20% rule in The Fabricator; some of his columns put 5052-H32 nearer 11 to 13%, so confirm with a test bend). The calculator uses the middle of each range. Bottoming presses the sheet into the die and needs around five times the air-bend force; coining drives the punch tip into the material and needs ten times or more, which is why it is rarely used on modern brakes.
Common use cases
Checking a job against the press
Make sure the total force and the force per metre stay inside the press and tooling ratings before setting up.
Choosing a V-die
Balance force against inside radius and minimum flange length when picking the die opening.
Design for manufacture
Check that flange lengths and radii on a drawing can actually be formed on the available tooling.
Quoting thicker work
Find out quickly whether a plate job needs a bigger brake or a subcontractor.
Tips and limitations
- Schedule VI of the Model Rules says no power press may be used unless it has been thoroughly examined and tested by a competent person within the previous 12 months, and new presses are examined after installation before first use.
- State factory rules can differ from the Model Rules in detail, and the move to the OSH Code, 2020 changes the legal basis, so check what applies in your state with the Inspector of Factories.
- Use the tensile strength from the mill test certificate; the force scales directly with it.
- Keep V between about 6 and 12 times the thickness. Too narrow a die raises the force and can crack the outside of the bend.
Sources and further reading
- Model Rules under the Factories Act, 1948, DGFASLI, Ministry of Labour and Employment. Schedule VI, Power Press: applies to press brakes; 12-monthly thorough examination and test.
- The Occupational Safety, Health and Working Conditions Code, 2020 (Gazette of India), DGFASLI, Ministry of Labour and Employment. Section 1(2) commencement by notification; section 143 repeals the Factories Act, 1948 and keeps rules made under it in force, where not contrary to the Code, until repealed.
- IS 2062:2011 Hot rolled medium and high tensile structural steel, Specification, Bureau of Indian Standards (Public.Resource.Org copy). Table 2: minimum tensile strength 410 MPa for E250 and 490 MPa for E350.
- IS 2062:2011 Hot rolled medium and high tensile structural steel, Bureau of Indian Standards. Grades E250 to E650 with sub-qualities A, BR, B0 and C; minimum tensile and yield values set for each grade.
Frequently asked questions
How many tonnes does a press brake need for 2 mm MS sheet?
About 16.9 tonnes per metre in a 16 mm die, so 41.1 tonnes for a full 2440 mm (8 ft) bend. Halve the bend length and the force halves.
What thickness can a 100 tonne press brake bend over 8 feet?
In MS with an 8 x T die, about 3 mm: at that thickness a 2440 mm bend needs about 62 tonnes, while 4 mm needs about 82 tonnes and 5 mm over 100. Check the maker's chart for your exact dies.
Does the power press schedule of the Model Rules cover press brakes?
Yes. Schedule VI of the Model Rules framed under the Factories Act says it applies to all types of power presses including press brakes, except when used for working hot metal. Which rules bind your factory depends on your state and the move to the OSH Code, 2020, so confirm with the Inspector of Factories.
How often does Schedule VI require a power press to be examined?
At least once in every 12 months: a competent person thoroughly examines and tests it, and a report of each examination is kept for inspection. Ask your state's Inspector of Factories whether these rules or rules made under the OSH Code, 2020 apply to you.
What tensile strength should I use for MS sheet?
The mild steel preset uses 414 N/mm² (60 ksi), the baseline of the 575 tonnage rule. For a named grade, use the tensile strength on the test certificate; for IS 2062 E250 the minimum is 410 N/mm².
Is there an in-depth guide to the Press Brake Tonnage Calculator?
Yes. “Press Brake Tonnage, V-Die Width and the Air-Bent Radius” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.