India version. Starts on an 8 x 4 ft (2440 x 1220 mm) MS sheet in 18 SWG, the British gauge table rather than the US one, with weight in kg and per sq ft. US version

MS and GI Sheet Weight Calculator (SWG and mm)

Weight of an MS, GI, stainless or aluminium sheet in kg from size in mm and thickness or SWG gauge, for 8 x 4 ft sheets, with kg per sq ft and holes taken off.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Sheet Metal Weight Calculator?

MS, CRCA and GI sheet thickness may be given in mm or as a gauge number ("18 gauge", "22 gauge"), and a gauge number means little until you know which table it comes from. This version opens on an 8 x 4 ft sheet in the British SWG table: a 2440 x 1220 mm MS sheet in 18 SWG (1.219 mm) weighs 28.49 kg, which is 9.57 kg per square metre or 0.889 kg per sq ft.

The gauge table matters. Most charts online are American, and their 22 gauge is 0.759 mm while 22 SWG is 0.711 mm. On a full 8 x 4 sheet that is 17.75 kg against 16.62 kg, so a rate per sheet worked out from the wrong chart is off by about 7%. Keep the gauge table on SWG unless the supplier tells you otherwise.

For GI sheet, the zinc adds a little on top of the steel. JSW, for example, lists its galvanised sheet to IS 277 from 0.13 to 3.0 mm with coatings up to 275 g/m², so a heavily coated 8 x 4 sheet carries up to about 0.8 kg of zinc. Use the steel weight here and add the coating from the supplier's test certificate if you need the invoice weight.

  • Ten material presets with typical published densities, plus custom density
  • Thickness by value or by gauge from five gauge tables, including British SWG
  • Round holes and rectangular cut-outs subtracted
  • Weight per piece, batch total, kg/m² and lb/ft²
  • Same-size weight in every other material, copy and share link
Read the guide: How to Calculate Sheet Metal Weight (and Why Gauge Tables Disagree)

Updated

How to use the Sheet Metal Weight Calculator

  1. Keep the units on metric and enter the size in mm (2440 x 1220 for an 8 x 4 ft sheet).
  2. Leave the thickness on "Gauge number" with the SWG table and pick the gauge, or switch to a thickness in mm.
  3. Choose mild steel for MS, CRCA and GI base steel; stainless and aluminium have their own densities.
  4. Set the number of sheets, and add punched holes or cut-outs if the parts have them.

Worked examples

8 x 4 ft MS sheet, 18 SWG

Input

2440 x 1220 mm, 18 SWG (1.219 mm), mild steel 7,850 kg/m³

Output

28.49 kg per sheet, 9.57 kg/m² (0.889 kg/sq ft)

Multiply the per sq ft figure by the 32 sq ft of an 8 x 4 sheet to check: 0.889 x 32 = 28.5 kg.

Ten GI sheets, 22 SWG

Input

2440 x 1220 mm, 22 SWG (0.711 mm), steel base, quantity 10

Output

16.62 kg each, 166.2 kg for ten (steel only)

With a coating of up to 275 g/m² add up to about 0.82 kg per sheet for the zinc. A US 22 gauge chart would give 17.75 kg per sheet instead.

5 mm MS plate, 2500 x 1250 mm

Input

2500 x 1250 x 5 mm, mild steel

Output

122.7 kg, 39.25 kg/m²

At plate thickness gauges are no longer used and dealers quote in mm. A plate this heavy needs a chain block or forklift, not two people.

Background and insight

The default densities are typical published values: 7,850 kg/m³ for carbon steel (the value used throughout EN 1993 and most steel tables), 7,930 kg/m³ for 304 stainless, 2,680 kg/m³ for 5052 aluminium, 2,700 kg/m³ for 6061, 8,890 kg/m³ for C110 copper and 8,530 kg/m³ for C260 cartridge brass, the last two from Copper Development Association data. Alloys vary by a percent or so, so a custom density is available.

Steel sheet gauges carry a built-in weight. The Manufacturers’ Standard Gauge was defined from weight, at 41.82 lb per square foot per inch of thickness, which corresponds to about 8,030 kg/m³. That is why a nominal 16 gauge sheet is listed in old tables at 2.5 lb/ft² while 0.0598 in at 7,850 kg/m³ comes to 2.44 lb/ft². The calculator uses the density you pick, so expect results about 2% below the traditional gauge weight tables for steel.

Real sheet is rarely exactly nominal. Mills roll to a thickness tolerance (ASTM A568 for carbon steel sheet, ASTM A480 for stainless) and sheets tend to be thinner at the edges than in the middle. For shipping and lifting, round up; for costing by weight, ask the supplier whether they invoice on theoretical or actual weight.

Common use cases

  • Freight and handling

    Know the weight of a bundle before booking a truck or choosing a lifting clamp or forklift.

  • Material costing

    Convert a price per kilogram or pound into a price per sheet or per part.

  • Structural and enclosure design

    Estimate the dead weight of cladding, guards, ducts and panels for supports and fixings.

  • Comparing materials

    See how much an aluminium or stainless version of a steel part would weigh before redesigning it.

Tips and limitations

  • The quick rule for steel: kg per square metre = thickness in mm x 7.85, and kg per sq ft = thickness in mm x 0.729.
  • Ask whether a rate per kg is on theoretical weight (as here) or actual weighed weight; sheet rolled to the thin side of its tolerance weighs less.
  • For a bent part, weigh the flat blank from the bend allowance calculator, not the finished outside size.
  • Higher SWG numbers are thinner: 16 SWG is 1.626 mm, 20 SWG is 0.914 mm, 24 SWG is 0.559 mm.

Sources and further reading

  1. Galvanised steel, JSW Steel. GI sheet to IS 277, 0.13 to 3.0 mm thick, coatings up to 275 g/m².
  2. Hot rolled steel, JSW Steel. Hot rolled coil and sheet sizes from Indian mills.
  3. Standard wire gauge, Wikipedia. History of SWG and the full gauge table.

Frequently asked questions

What is the weight of an 18 gauge MS sheet of 8 x 4 feet?

About 28.5 kg in 18 SWG (1.219 mm) at 7,850 kg/m³. If the sheet is actually a US 18 gauge (1.214 mm) it is almost the same, but at other gauges the two tables differ more.

How thick is 22 gauge GI sheet in mm?

0.711 mm if the gauge is SWG. The American 22 gauge is 0.759 mm for plain steel, so always confirm which gauge a quotation uses.

How do I calculate sheet weight per sq ft?

Thickness in mm x 7.85 gives kg per square metre; multiply by 0.0929 for kg per sq ft. For 18 SWG that is 9.57 kg/m², or 0.889 kg per sq ft.

Does the zinc coating change the weight of GI sheet?

Slightly. The coating mass is given in grams per square metre; at 275 g/m² an 8 x 4 sheet carries about 0.82 kg of zinc. Thin sheets are affected most in percentage terms.

What is SWG?

The British Standard Wire Gauge, fixed by Order in Council in 1883 for wire and also applied to sheet and tube wall. Each number maps to a thickness in thousandths of an inch: 16 SWG is 0.064 in (1.626 mm).

Is there an in-depth guide to the Sheet Metal Weight Calculator?

Yes. “How to Calculate Sheet Metal Weight (and Why Gauge Tables Disagree)” covers the background, how it works, common pitfalls and worked examples. Read the full guide.