India version. Checks a ramp in millimetres against the Harmonised Guidelines and Standards for Universal Accessibility in India 2021: gradient table, 9 m landings, 1200 mm width and handrails. US version
Ramp Slope Calculator (Harmonised Accessibility Guidelines)
Ramp length, runs and landings for a wheelchair ramp from the plinth height, checked against India's Harmonised Guidelines: 1:12 to 1:20, 1200 mm clear width.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Ramp Calculator?
In India the accessibility rules for ramps come from the Harmonised Guidelines and Standards for Universal Accessibility in India 2021, issued by the Ministry of Housing and Urban Affairs and adopted by many public bodies. Their Table 1 links the gradient to the longest horizontal run: 6 m at 1:12, 9 m at 1:14, 11 m at 1:15, 15 m at 1:20 and 18 m at 1:25, with interpolation between rows. Landings are also needed at least every 9,000 mm of horizontal run, and the clear width must be at least 1,200 mm.
Most Indian buildings sit on a raised plinth, often 450 to 900 mm above the road or compound, so the ramp to the entrance is longer than people expect. Enter the plinth height and the gradient, and the tool splits the ramp into runs, adds the 1,500 mm landings, checks the number of runs (no more than four) and gives the footprint you need in front of the building.
- ADA 2010 Section 405, existing-site Table 405.2, IRC R311.8 and custom slopes
- Run, sloped length, angle, percent and number of runs
- Landings and straight footprint, handrail length per side
- Pass or fail checks with section numbers
- Inches or millimetres, copy and share link
Updated
How to use the Ramp Calculator
- Measure the rise from the finished ground or road level to the entrance floor, in mm.
- Keep the rule on India Harmonised Guidelines 2021 and enter the gradient as a ratio (12 for 1:12).
- Enter the clear width between handrails, at least 1,200 mm.
- Leave the landing blank to use 1,500 mm, or enter the length you can provide.
- Read the checks: gradient, run length, number of runs, width, landings and handrails.
Worked examples
Shop entrance on a 600 mm plinth, 1:12
Input
Rise 600 mm, 1:12, width 1200 mm
Output
Two runs of 300 mm rise and 3.6 m run; 7.2 m of ramp, 11.7 m footprint with three landings
At 1:12 a run may be 6 m at most, which allows 500 mm of rise, so 600 mm needs two runs and an intermediate landing. Handrails are needed on both sides because each run rises more than 150 mm.
Clinic on a 900 mm plinth, 1:12
Input
Rise 900 mm, 1:12, width 1200 mm
Output
Two runs of 450 mm rise over 5.4 m each; 10.8 m of ramp; 15.3 m footprint
Within the limits of four runs and 6 m per run. If the site in front is shorter than 15 m, turn the ramp at the intermediate landing to make a dog-leg.
A gentler 1:15 ramp for a 1.2 m rise
Input
Rise 1200 mm, 1:15, width 1500 mm
Output
Two runs of 600 mm over 9 m each; 18 m of ramp; 22.5 m footprint
Table 1 would allow an 11 m run at 1:15, but the 9,000 mm landing interval in the ramps section caps each run at 9 m. A rise of this size is where the guidelines suggest considering a lift.
Background and insight
The rules come from Section 405 of the 2010 ADA Standards. The running slope may not be steeper than 1:12 (405.2) and the cross slope not steeper than 1:48 (405.3). Clear width between handrails is at least 36 inches (405.5). The rise of any single run is 30 inches at most (405.6). Landings at the top and bottom of every run are at least as wide as the ramp and at least 60 inches long, and a landing where the ramp changes direction is at least 60 by 60 inches (405.7). Runs that rise more than 6 inches need handrails on both sides (405.8), mounted 34 to 38 inches high (505.4) and extending 12 inches beyond the top and bottom of the run (505.10).
Existing sites get limited relief under Table 405.2 when space does not allow 1:12: a slope between 1:12 and 1:10 is allowed for a rise of 6 inches at most, and between 1:10 and 1:8 for a rise of 3 inches at most. Nothing steeper than 1:8 is permitted.
Homes follow the International Residential Code where adopted. IRC R311.8 sets a maximum ramp slope of 1:12, allowing 1:8 only where 1:12 is technically infeasible, requires 36 by 36 inch landings at the top and bottom, at doors and at turns, and requires a handrail on at least one side of ramps steeper than 1:12. Many people still build home ramps to ADA dimensions because they are easier to use. Loading ramps for vehicles and equipment are outside these rules; follow the equipment maker's maximum angle.
Common use cases
Home access
Size a ramp for a wheelchair user before buying a modular kit or lumber.
Small businesses
Check an entrance ramp against ADA 405 before a contractor quote or an accessibility review.
Thresholds and small changes in level
Use the existing-site table for short ramps of a few inches where space is tight.
Sheds, trailers and loading docks
Work out the length for a mower, cart or hand truck at any slope.
Tips and limitations
- Provide steps as well as the ramp: the guidelines note many ambulant disabled people find steps easier and safer.
- Fit a 75 mm kerb or a rail with its lower edge 75 mm or less above the surface wherever a ramp or landing is not against a wall.
- Place a row of tactile warning tiles at the start and end of every run.
- Cover external ramps where possible; monsoon rain makes an uncovered ramp slippery.
Sources and further reading
- Accessibility standards for branch premises, reproducing the Harmonised Guidelines and Standards for Universal Accessibility in India 2021 (external ramps), Pension Fund Regulatory and Development Authority. Pages 4 to 7: Table 1 gradients and runs, width, landings, handrails and edge protection. The clause numbers in this circular are its own, not the Guidelines'.
- Harmonised Guidelines and Standards for Universal Accessibility in India 2021, Ministry of Housing and Urban Affairs, Government of India (copy on the Department of Empowerment of Persons with Disabilities site)
Frequently asked questions
What is the standard slope for a ramp in India?
No steeper than 1:12 under the Harmonised Guidelines 2021, and gentler where space allows. Table 1 sets the longest horizontal run for each gradient: 6 m at 1:12, 9 m at 1:14, 11 m at 1:15, 15 m at 1:20 and 18 m for gradients not gentler than 1:25.
What is the minimum width of a wheelchair ramp in India?
A clear width of 1,200 mm under the Harmonised Guidelines 2021, ramps section. This is wider than many older ramps, which were built to 900 or 1,000 mm.
How often does a ramp need a landing?
At the top and bottom of every run, where the ramp changes direction, and at intervals of not more than 9,000 mm of horizontal run. Each landing should be a level platform of at least 1,200 x 1,500 mm. The guidelines also limit a ramp to four runs, that is three intermediate landings.
When are handrails required on a ramp?
On both sides of any run that rises more than 150 mm, at a height of 750 to 900 mm, extending at least 300 mm beyond the top and bottom, with a round section of 38 to 50 mm.
How long should a ramp be for a 450 mm plinth?
At 1:12 the horizontal run is 450 x 12 = 5,400 mm, which fits in one run. Add 1,500 mm landings at the top and bottom and the footprint is 8.4 m.
Can a ramp be curved?
The guidelines say curved ramps should be avoided, and where one is used its gradient should be 1:16 or gentler.
Is there an in-depth guide to the Ramp Calculator?
Yes. “ADA Ramp Rules: Slope, Rise, Landings and Handrails” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.