India version. Rounds up to BIS IS 1180 preferred ratings (16 to 2,500 kVA), with 11 kV primaries and the 433 V no-load secondary used for Indian distribution transformers. US version

Transformer Sizing Calculator (India, IS 1180)

Size a distribution transformer from kW, kVA or amps, round up to an IS 1180 rating such as 63, 100, 160 or 250 kVA, and get 11 kV and 433 V full-load currents.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Transformer Sizing Calculator?

Distribution transformers in India step 3.3, 6.6, 11, 22 or 33 kV down to a 433 V three phase secondary, and IS 1180 lists their standard ratings: 16, 25, 63, 100, 160, 200, 250, 315 kVA and so on up to 2,500 kVA. This version picks from that list, so a calculated 48 kVA rounds up to 63 kVA, the next IS rating, and not to 50 kVA, which is not on the IS 1180 list.

Enter the connected or demand load as kW with a power factor, kVA or amps, add spare capacity, and the tool returns the IS rating, how loaded it will be and the full-load current on each side. A 120 kW load at 0.9 with 20% spare needs 160 kVA, carrying 8.4 A on 11 kV and 213 A at 433 V.

That secondary current sets the LT panel incomer and the cable or bus duct from the transformer, so it is the figure your panel builder will ask for.

  • Load from kW and PF, kVA or amps
  • Spare capacity and next standard rating (ANSI or IEC lists)
  • Primary and secondary full-load and actual load currents
  • Voltage (turns) ratio
  • Comparison table of neighbouring sizes
Read the guide: Transformer Sizing: kVA, Full-Load Amps and Standard Ratings

Updated

How to use the Transformer Sizing Calculator

  1. Choose single-phase or three-phase.
  2. Enter the load as kW with power factor, as kVA, or as amps at the secondary voltage.
  3. Set the spare capacity you want, for example 20% for growth.
  4. Enter the primary and secondary voltages (line to line for three-phase) and choose North American or IEC ratings.
  5. Read the standard size, how heavily it is loaded today, the full-load currents and the voltage ratio.

Worked examples

120 kW commercial load on 11 kV

Input

Three phase, 120 kW at PF 0.9, 20% spare, 11,000 V to 433 V, IS 1180

Output

133.3 kVA load, 160 kVA required, 160 kVA (83% loaded); 8.40 A at 11 kV, 213.3 A at 433 V

The required 160 kVA lands exactly on a standard rating. If the load is likely to grow, the next rating, 200 kVA, would run at 67% today.

Why the IS list matters: 40 kVA load

Input

Three phase, 40 kVA, 20% spare, 11,000 V to 433 V; IS 1180 vs IEC list

Output

IS 1180: 63 kVA (63% loaded, 84.0 A at 433 V). IEC list: 50 kVA

50 kVA is not an IS 1180 rating; 40 kVA is listed only as non-preferred. Rounding to the IS list keeps the choice to a standard rating.

Factory with 25% growth margin

Input

Three phase, 520 kW at PF 0.95, 25% spare, 11,000 V to 433 V, IS 1180

Output

547.4 kVA load, 684.2 kVA required, 800 kVA (68% loaded); 42.0 A at 11 kV, 1,066.7 A at 433 V

630 kVA falls short of 684 kVA, so 800 kVA is chosen. CPWD planning guidance suggests at least two transformers where reliable supply matters, so two 400 kVA units are worth comparing.

Background and insight

Transformers are rated in kVA rather than kW because their heating depends on current and voltage, not on the power factor of the load. Full-load current is I = kVA × 1000 ÷ V for single-phase and I = kVA × 1000 ÷ (√3 × V(LL)) for three-phase. A 75 kVA three-phase unit stepping 480 V down to 208Y/120 V carries 90.2 A on the primary and 208.2 A on the secondary.

The load figure should be the calculated demand, after any diversity your code allows, not the sum of nameplates. Designers then add spare capacity, commonly 20 to 25%, so that the unit runs at about 80% of its rating today. That margin covers growth, keeps losses and temperature rise down, and leaves room for motor starting. Harmonic-rich loads (computers, drives, LED drivers) may need a K-factor rated transformer or a further derating.

For an ideal transformer the voltage ratio equals the turns ratio, a = Vp ÷ Vs = Np ÷ Ns, and current goes the other way: Is = Ip × a. In three-phase units the per-winding ratio depends on the connection; a delta-wye 480 to 208Y/120 V transformer has 480 V on each delta winding and 120 V on each wye winding, a winding ratio of 4:1, even though the line-to-line ratio is 2.31:1. Ratings follow ANSI/IEEE C57.12 series standards in North America and IEC 60076 elsewhere; protection follows NEC 450.3 or your local code.

Common use cases

  • Specifying a step-down transformer

    Choose the kVA for a 480 to 208/120 V panel feeding receptacles and lighting.

  • Machine isolation transformers

    Size a control or isolation transformer for imported equipment that needs a different voltage.

  • Checking an existing unit

    See how loaded a transformer is by entering the measured secondary amps.

  • Planning protection

    Get primary and secondary full-load amps as the starting point for breakers and conductors.

Tips and limitations

  • IS 1180 covers oil-filled distribution transformers in Part 1 and ester-filled ones in Part 2; ratings of 6.3, 10, 20 and 40 kVA three phase are non-preferred and are left out of this list.
  • For a building that is lightly loaded after hours, CPWD suggests evaluating a smaller transformer for that period to cut core loss, which runs 24 hours a day regardless of load.
  • Ask for the rated current at 433 V on the data sheet; at 415 V the same kVA gives about 4% more current, so be consistent when sizing the incomer.
  • Improve power factor before sizing: at 0.7 a 100 kW load needs 143 kVA, at 0.95 only 105 kVA.

Sources and further reading

  1. Transformers: summary of Indian Standards (IS 1180 and others), Bureau of Indian Standards. Distribution voltages, 433 V (250 V) secondaries, and IS 1180 standard ratings.
  2. General Specifications for Electrical Works, Part I: Internal (2013), clause 2.3, Central Public Works Department, Government of India. Stand-by systems with a minimum of two transformers; smaller transformer for off-peak hours.
  3. IEC 60076-1 Power transformers: General, International Electrotechnical Commission

Frequently asked questions

What are the standard transformer ratings in India?

IS 1180 lists three phase ratings of 16, 25, 63, 100, 160, 200, 250, 315, 400, 500, 630, 800, 1,000, 1,250, 1,600, 2,000 and 2,500 kVA, with 6.3, 10, 20 and 40 kVA as non-preferred. Single phase ratings are 5, 10, 16 and 25 kVA, with 50, 75 and 100 kVA non-preferred.

Why is the secondary 433 V and not 415 V?

Distribution transformers are rated at 433 V no-load so that, after the voltage drop inside the transformer and the LT cables, consumers receive close to the nominal 415 V. The BIS summary of its standards describes distribution transformers as having a 433 V three phase (250 V single phase) secondary.

How many amps is a 100 kVA transformer?

At 433 V, 100,000 ÷ (√3 × 433) = 133.3 A on the LT side. On 11 kV it is 5.25 A. Enter 100 kVA with no spare to see both.

How do I calculate the transformer size for my building?

Add the demand load in kW, divide by the expected power factor to get kVA, add a growth margin of 20 to 25%, and pick the next IS 1180 rating. Use demand after diversity, not the sum of every connected load.

Should I install one transformer or two?

CPWD planning guidance for buildings needing reliable supply calls for a minimum of two transformers, so that one can stand by if the other fails. Two smaller units also let you switch one off at light load to save core losses.

Is there an in-depth guide to the Transformer Sizing Calculator?

Yes. “Transformer Sizing: kVA, Full-Load Amps and Standard Ratings” covers the background, how it works, common pitfalls and worked examples. Read the full guide.