Australia version. Builds up the Total R-Value in m²K/W the way the NCC and ABCB describe it, with batts entered by their labelled R-value and layers in mm. US version

Total R-Value and Heat Loss Calculator (Australia)

Add up the Total R-Value of a brick veneer or framed wall, ceiling or floor from its layers and batts, then see the heat flow in watts for a room in winter.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Heat Loss and U-Value Calculator?

Australian insulation is sold and specified by R-value in m²K/W: an R2.5 wall batt, an R6.0 ceiling batt. The NCC Housing Provisions Part 13.2 sets minimum insulation R-values for roofs, ceilings, walls and floors by climate zone, and for metal-framed walls it asks for a minimum Total R-Value for the whole build-up, calculated to AS/NZS 4859.2 (Tables 13.2.5p to 13.2.5r).

Total R-Value is the sum of every layer in the element: plasterboard, the batt, any airspace, the cladding or brick, and the surface air films on each side. This calculator adds them in the same way. Enter a batt as a "known R-value" layer using the figure on its label, enter materials by thickness and conductivity, and the result shows the Total R-Value and its inverse, the U-value.

A brick veneer wall with 10 mm plasterboard, an R2.5 batt, a 0.18 cavity and 110 mm brick comes to a Total R-Value of about 3.03. The batt does most of the work: without it the same wall would lose several times as much heat.

  • Up to ten layers by thickness and conductivity or by known R-value
  • ISO 6946 and ASHRAE surface resistances for walls, roofs and floors
  • R-value and U-value in both SI and US units at once
  • Heat loss in watts and BTU/h, plus seasonal kWh and therms from degree-days
  • Layer share table and steady-state interface temperatures
Read the guide: U-Value, R-Value and Heat Loss: Calculating a Wall Layer by Layer

Updated

How to use the Heat Loss and U-Value Calculator

  1. Keep the units on metric. List the layers from the room side outwards.
  2. For a batt or blanket, pick "Known R-value" and type the R-value printed on the pack, reduced if the batt will be squashed into a thinner cavity.
  3. Add plasterboard (10 or 13 mm), the cavity and the cladding or 110 mm brick by thickness and conductivity.
  4. Choose the surface resistances for a wall, a ceiling (heat flow up) or a floor (heat flow down).
  5. Enter the room area and an inside and outside temperature to see the heat flow in watts.

Worked examples

Brick veneer wall: R2.0 or R2.5 batt

Input

10 mm plasterboard, batt, 0.18 airspace, 110 mm brick (k 0.77); 25 m² of wall, 20 °C inside, 5 °C outside

Output

R2.5 batt: Total R 3.03, U 0.330, 124 W; R2.0 batt: Total R 2.53, U 0.395, 148 W

The half-step in batt rating changes the wall's heat flow by about 16%. Timber studs bridge the batt, so the wall as built performs a little below this clear-field figure.

Ceiling batts under a pitched roof

Input

10 mm plasterboard ceiling with R4.0 or R6.0 batts, ceiling films; 150 m², 20 °C inside, 5 °C in the roof space

Output

R4.0: Total R 4.18, U 0.239, 538 W; R6.0: Total R 6.18, U 0.162, 364 W

Going from R4.0 to R6.0 cuts winter heat flow through the ceiling by about a third. The roof space, sarking and roofing add more resistance on top of this in a full NCC calculation.

Background and insight

The method is the one in ISO 6946 and the ASHRAE Handbook of Fundamentals: thermal resistances of layers that the heat crosses one after another simply add, R = d / k for each homogeneous layer, and U is the reciprocal of the total. Surface resistances account for the thin film of still air on each face. ISO 6946 uses 0.13 m²·K/W inside for walls, 0.10 for heat flowing up through a roof or ceiling, 0.17 for heat flowing down through a floor, and 0.04 outside. ASHRAE tabulates the same idea in US units: R-0.68 for still air on a vertical surface and R-0.17 for a 15 mph winter wind.

US and SI R-values describe the same property in different units, which is why a product sold as R-13 in the United States is RSI 2.29 elsewhere. One m²·K/W equals 5.678 ft²·°F·h/BTU. Conductivities in the material list are typical design values from ISO 10456, CIBSE Guide A and manufacturer literature; insulation products vary with density and age, so the declared lambda value on the datasheet should replace the default whenever you have it.

A clear-field calculation like this ignores thermal bridges. In a timber stud wall the studs occupy roughly 15 to 25% of the area and conduct three times better than mineral wool, so the whole-wall U-value is noticeably worse than the clear-field one. Steel studs are far worse again. Full heat-load methods (ACCA Manual J, EN 12831) add bridging, ventilation and infiltration on top of the fabric losses calculated here.

Common use cases

  • Comparing insulation upgrades

    See how much an extra 50 mm of PIR board or a thicker batt changes the U-value and the seasonal kWh before pricing the work.

  • Building regulations checks

    Check that a proposed wall or roof meets a target U-value such as 0.18 or 0.26 W/m²·K, then confirm with a full ISO 6946 calculation including bridging.

  • Sizing a room heater

    Add up the fabric losses of each wall, ceiling and floor to get a first estimate of the heat a room needs at the design outdoor temperature.

  • Condensation screening

    Use the interface temperatures to see where a wall drops below the indoor dew point and where a vapour control layer belongs.

Tips and limitations

  • NCC 13.2.2 notes that compressing insulation lowers its R-value; an R2.5 batt pushed into a 70 mm stud will not deliver R2.5.
  • Metal framing conducts heat far more than timber, which is why the NCC adds thermal break and Total R-Value rules for metal-framed walls and roofs.
  • For the whole house, NatHERS energy rating software models every element, the glazing and the climate together; this tool helps compare one wall or ceiling option against another.

Sources and further reading

  1. NCC 2025 Housing Provisions, Part 13.2 Building fabric, Australian Building Codes Board. 13.2.2 insulation to AS/NZS 4859.1 and compression; 13.2.5 external walls by climate zone; Tables 13.2.5p to 13.2.5r Total R-Value for metal-framed walls.
  2. NCC 2025 Housing Provisions, Schedule 1 Definitions: Total R-Value, Australian Building Codes Board. Total R-Value: the sum of the R-Values of the component layers, including building materials, insulation, airspaces, thermal bridging and surface resistances.

Frequently asked questions

What is Total R-Value in the NCC?

The NCC 2025 Housing Provisions glossary defines it as the sum of the R-Values of the individual component layers in a composite element, including any building material, insulating material, airspace, thermal bridging and associated surface resistances. Product R-values on batts and boards are the insulation alone; the Total R-Value adds everything else in the wall or ceiling. This calculator adds clear-field layers only and leaves out the thermal bridging.

What R-value insulation do I need in my walls?

It depends on the climate zone and on the wall type, its colour and the eaves overhang: NCC Housing Provisions 13.2.5 has separate tables for each climate zone. Your energy assessor or building surveyor will confirm which table applies, or use a NatHERS rating to show compliance instead.

Do metal-framed walls need more insulation?

Often, yes. NCC 13.2.5(4) asks metal-framed walls to reach a minimum Total R-Value calculated to AS/NZS 4859.2, or to follow one of the deemed options with thermal breaks. For a lightweight metal-framed wall, Table 13.2.5q links an R2.0 insulation layer to a minimum Total R-Value of 1.89 and R2.5 to 2.06. This calculator's sum leaves out the metal frame, so do not compare it with Tables 13.2.5p to 13.2.5r; those need an AS/NZS 4859.2 Total R-Value or a deemed option in Tables 13.2.5s to 13.2.5u.

Should I count the air films when adding up R-values?

For a wall or ceiling Total R-Value, yes: the inside and outside surface resistances are part of it. Some NCC tables are different; the metal-framed ceiling and floor tables note that they leave out internal air films, roof spaces or subfloor spaces, so read the notes under the table you are checking against.

How do I turn an R-value into heat loss in watts?

Divide 1 by the Total R-Value to get the U-value, then multiply by the area and the temperature difference. A 25 m² wall with Total R 3.03 at a 15 °C difference loses about 124 W.

Is there an in-depth guide to the Heat Loss and U-Value Calculator?

Yes. “U-Value, R-Value and Heat Loss: Calculating a Wall Layer by Layer” covers the background, how it works, common pitfalls and worked examples. Read the full guide.