Australia version. Metric tile sizes and m² boxes as Australian tile shops sell them, A$ prices, and a reminder that NCC Part 10.2 sets wet area waterproofing under the tiles. US version

Tile Calculator (Australia)

How many tiles and boxes for a bathroom, splashback or alfresco in mm tile sizes and m², with grout in kg, an A$ cost and NCC wet area waterproofing notes.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Tile Calculator?

Australian tiles are sold by the square metre, with box labels showing m² per box: 600 x 600 porcelain for floors and alfrescos, 300 x 600 for walls, 75 x 300 subway for splashbacks. This version works in mm and m², and rounds up to whole boxes.

A bathroom floor 2.4 by 1.9 m in 600 x 600 tiles with a 2 mm joint and 10% waste needs 14 tiles, four boxes of 1.44 m². An outdoor alfresco of 24 m² in the same tile with a 3 mm joint needs 73 tiles, 19 boxes.

In bathrooms and laundries, the tiles sit on a waterproofing system. The NCC Housing Provisions Part 10.2 (or AS 3740) sets out what must be waterproof or water resistant in wet areas, Check whether your state requires waterproofing to be done by a licensed or registered waterproofer and certified. Budget for it alongside the tiles.

  • Grout joint counted in every tile, not just the tile face
  • Layout presets for straight, offset, diagonal and herringbone waste, all editable
  • Boxes from tiles per box or coverage per box, with a cost estimate
  • Grout weight in kg and lb from the published manufacturer formula
  • Imperial and metric with automatic conversion; copy and share link
Read the guide: Estimating Concrete, Flooring, Tile and Gravel Without Running Short

Updated

How to use the Tile Calculator

  1. Keep units on metric. Enter the area in metres or type the m².
  2. Subtract the shower base, vanity and doors.
  3. Enter the tile size and joint in mm, and choose the layout to preset the waste.
  4. Enter the m² per box from the label and the box price in A$.

Worked examples

Bathroom floor in 600 x 600 porcelain

Input

2.4 x 1.9 m, 600 x 600 mm, 2 mm joint, 10% waste, boxes of 1.44 m²

Output

14 tiles (12.6 exact); 4 boxes; about 0.5 kg grout

The shower area falls to the waste, so lay the tiles out with the falls in mind; tiles on a fall need more cuts.

Kitchen splashback in subway tiles

Input

3.0 x 0.6 m, 300 x 75 mm, 2 mm joint, 15% waste, boxes of 1 m²

Output

90 tiles (77.4 exact); 3 boxes; about 0.8 kg grout

Splashbacks have power points and window returns to cut around, so allow 15%.

Alfresco in 600 x 600 outdoor tiles

Input

24 m², 600 x 600 mm, 3 mm joint, 10% waste, boxes of 1.44 m²

Output

73 tiles (66 exact); 19 boxes; about 4.2 kg grout

Use a tile rated for outdoor slip resistance and leave movement joints as the tile adhesive maker specifies.

Background and insight

Each tile occupies its own size plus one joint in each direction. A 12 inch tile with a 1/8 inch joint takes up 12.125 x 12.125 inches, about 2% more than the tile, so a calculator that ignores joints overstates the count for large tiles and is close enough only for very small joints. The difference grows quickly with mosaic and small subway tiles, where the joint is a larger share of each piece.

Waste comes from cuts at the edges. A straight lay wastes mainly the offcuts along two walls. Diagonal and herringbone patterns cut nearly every edge piece at an angle, and the triangles left over are rarely reusable, so installers plan 15 to 20%. Large-format tiles also waste more because a single bad cut costs a big piece. Keep a few spare tiles after the job; matching the dye lot years later is often impossible.

The grout figure comes from (A + B) / (A x B) x C x D x density, with tile length A, width B, tile thickness C and joint width D in millimetres and a density around 1.6 kg per litre for cement grout. It gives kilograms per square metre of floor.

Common use cases

  • Bathroom and kitchen floors

    Subtract the tub, vanity or cabinet footprint and get a box count to order before demolition starts.

  • Shower and backsplash walls

    Enter each wall as a length by height, subtract the window or niche, and use a small tile with its real joint.

  • Comparing tile options

    Change tile size and price per box to see how a larger format or different pattern changes the order and total cost.

  • Ordering grout with the tile

    Use the grout weight to choose between a small and large bag so the job is not held up halfway.

Tips and limitations

  • Check the slip rating for wet and outdoor areas against AS 4586 classifications; your tile shop can tell you the rating.
  • Keep the batch or shade number from the box so later purchases match.
  • Cutting porcelain and stone with power tools makes silica dust; wet cutting and a P2 respirator reduce exposure.

Sources and further reading

  1. Part 10.2 Wet area waterproofing (NCC 2025 Housing Provisions), Australian Building Codes Board
  2. Waterproofing of wet areas, Building and Plumbing Commission (Victoria)

Frequently asked questions

How many 600 x 600 tiles do I need per square metre?

About 2.78 laid tight, or 2.76 with a 2 mm joint. Boxes of four tiles cover 1.44 m², so a 10 m² floor needs seven boxes before waste.

Do I need waterproofing before tiling a bathroom?

Yes. Tiles and grout are not waterproof. NCC Housing Provisions Part 10.2, or AS 3740, sets the waterproofing for shower areas, floors and walls in wet areas. Check whether your state requires waterproofing to be done by a licensed or registered waterproofer and certified.

How much extra tile should I buy?

Add 10% for straight lay, 15% for diagonal or herringbone, and more for small rooms with large tiles, where every cut wastes a lot of tile.

How much grout for a bathroom floor?

Less than a kilogram for a small floor in large-format tiles with narrow joints; the estimate above is 0.5 kg for 4.56 m². Grout bags state their coverage for a given tile size and joint, so compare with the bag.

What size tiles are most common in Australian homes?

Large-format 600 x 600 and 600 x 1200 mm porcelain is common for floors, 300 x 600 mm for bathroom walls and subway or finger tiles for feature walls and splashbacks. Enter whatever size you choose; the tool handles any rectangle.

Is there an in-depth guide to the Tile Calculator?

Yes. “Estimating Concrete, Flooring, Tile and Gravel Without Running Short” covers the background, how it works, common pitfalls and worked examples. Read the full guide.