Pulley Speed and V-Belt Length on UK 50 Hz Motors
Pulley speeds and belt lengths for UK drives: 50 Hz motor speeds, sizing a pulley with slip, SPA datum lengths, centre distance from a stock belt and PUWER guarding.
By Redbison Dev · · 9 min read

United Kingdom edition. Written for UK workshops and plant: induction motors on the 50 Hz supply (1,500 rpm synchronous for 4-pole), US 1,725 rpm machine plans corrected for UK speeds, narrow wedge belts by section and datum length (ISO 4184), inverter speeds and guarding under PUWER regulation 11. US edition
A belt drive in a UK workshop starts from a motor that turns slower than the one in most online pulley charts. The supply here is 50 Hz, so a 4-pole induction motor runs a little under 1,500 rpm, not the 1,750 to 1,800 rpm of a 60 Hz American motor. Get that right, size the driven pulley with a little allowance for slip, and the rest is geometry: the belt length from the centre distance, or the centre distance from a stock belt. This edition works through a UK drive with the Pulley and Belt Calculator (UK, 50 Hz motors) and covers the guarding duty that comes with it.
Motor speed on a 50 Hz supply
The Electricity Safety, Quality and Continuity Regulations 2002, regulation 27, set the declared frequency of the public supply at 50 hertz, with a variation of no more than 1% either way, and the low voltage supply at 230 V. An induction motor's synchronous speed follows the frequency:
synchronous rpm = 120 x f / poles
| Poles | Synchronous speed at 50 Hz | At 60 Hz, for comparison |
|---|---|---|
| 2 | 3,000 rpm | 3,600 rpm |
| 4 | 1,500 rpm | 1,800 rpm |
| 6 | 1,000 rpm | 1,200 rpm |
The motor runs slightly below synchronous speed under load. Read the full-load speed from the nameplate rather than using the synchronous figure: two 4-pole motors of different sizes can differ by tens of rpm, which matters when you are aiming at a fan or spindle speed.
A US machine on UK mains
Plans and manuals from North America assume a 4-pole motor at about 1,725 rpm. A 3 inch (76.2 mm) motor pulley driving a 6 inch (152.4 mm) pulley gives 862.5 rpm there. Fit the same pulleys to a UK motor at 1,440 rpm and the driven shaft turns at 720 rpm, 17% slower. To get the planned 862.5 rpm back with the 6 inch driven pulley you need a driver of about 91.3 mm. The ratio is unchanged; only the starting speed fell with the frequency.
Sizing a pulley for a target speed
A belt that does not slip moves at the same speed over both pulleys, so D1 x n1 = D2 x n2. A friction V-belt does creep a little, so the driven pulley turns 1 to 3% slower than that ideal. The calculator includes a slip setting for exactly this.
Worked example: an extraction fan at 1,100 rpm
A workshop extraction fan should turn at about 1,100 rpm. The motor is 4-pole with a nameplate speed of 1,440 rpm, and the motor pulley is an SPA pulley of 125 mm datum diameter.
In the calculator, set Solve for to driven diameter and enter 125 mm, 1,440 rpm and 1,100 rpm:
- with no slip the driven pulley is 163.6 mm
- with 2% slip it is 160.4 mm
Pulleys come in fixed sizes, so pick the nearest one you can buy and recheck. With a 160 mm pulley and 2% slip the fan turns at 1,102.5 rpm (1,125 rpm with no slip). The belt runs at π x 0.125 x 1,440 / 60 = 9.42 m/s, well inside the range where V-belts work comfortably.
Belt length and centre distance
For an open belt, the exact pitch length from tangent geometry is:
L = 2√(C² − ((D − d)/2)²) + π(D + d)/2 + (D − d) asin((D − d)/2C)
and the handbook approximation drops the higher-order terms:
L ≈ 2C + π(D + d)/2 + (D − d)²/(4C)
With 125 and 160 mm pulleys the diameters are close, so the two agree to a fraction of a millimetre. At 450 mm centres the belt would be 1,348.4 mm long and the small pulley's wrap angle 175.5°.
Working back from a stock belt
UK narrow wedge belts are sold by section and datum length in millimetres, as ISO 4184 designates them: SPZ, SPA, SPB and SPC for groove datum widths of 8.5, 11, 14 and 19 mm, so "SPA 1250" is an SPA-section belt with a 1,250 mm datum length. Use the datum diameters of the pulleys with a datum length and the formulas line up.
Put the belt length in and solve for centre distance:
| Belt | Centre distance | Small pulley wrap |
|---|---|---|
| SPA 1250 | 400.8 mm | 175.0° |
| SPA 1400 | 475.8 mm | 175.8° |
Mount the motor on slide rails or a hinged base so it can move inward to slip the belt over the pulley flanges without levering it on, and outward to tension it and take up stretch as the belt beds in.
Running at other speeds with an inverter
An inverter (variable frequency drive) changes the motor speed in proportion to the frequency, so the same drive at 40 Hz runs at about 80% of its 50 Hz speed: the 1,440 rpm motor turns at about 1,152 rpm and the fan at about 882 rpm with 2% slip. The pulleys still set the ratio. A standard self-cooled motor run well below 50 Hz loses cooling from its own fan, and above 50 Hz its available torque falls, so check the motor and inverter data before relying on a large change.
Guarding the drive
A belt drive is a dangerous part of machinery as far as UK law is concerned: the in-running nip where the belt meets the pulley can draw in fingers and clothing. Regulation 11 of the Provision and Use of Work Equipment Regulations 1998 requires employers to take effective measures to prevent access to dangerous parts, in a set order: fixed guards enclosing the part first, then other guards or protection devices, then jigs and holders where those are not practicable, backed by information, instruction, training and supervision. The HSE's guidance on PUWER explains the duties. Design the guard and the belt adjustment together, so tensioning does not mean leaving the guard off.
Common mistakes
- Outside diameter instead of datum diameter. It overstates the length and shifts the ratio slightly. Use the pulley maker's datum diameter.
- Synchronous speed instead of nameplate speed. 1,500 rpm is a 4-pole motor with no load; the drive will run a few per cent slower.
- No slip allowance on a friction belt. Without it, a fan sized to the exact ratio ends up a little slow.
- No take-up. A fixed motor and an exact belt length leave no way to tension or re-tension the belt.
Tools for this job
- Pulley and Belt Calculator (UK, 50 Hz motors): pulley sizes and speeds with slip, belt speed, belt length, wrap angle and centre distance from a stock length.
- Torque and Power Calculator: shaft torque on each pulley.
- Gear Ratio Calculator: geared alternatives to a belt drive.
The US edition of this guide derives the exact and approximate length formulas in full and uses 60 Hz motor speeds.
Frequently asked questions
What speed does a 4-pole motor run at in the UK?
Its synchronous speed on 50 Hz is 120 x 50 / 4 = 1,500 rpm, and under load it runs a few per cent slower; the motor in this guide's example is rated at 1,440 rpm. Use the nameplate full-load speed.
Why does a machine built for the US run slow here?
Its motor turns at about 1,725 rpm on 60 Hz but at about 1,440 rpm on the UK's 50 Hz supply, so every driven shaft runs about 17% slower. A larger motor pulley or an inverter restores the speed.
What does SPA 1250 mean on a V-belt?
An SPA-section narrow wedge belt with a 1,250 mm datum length, as ISO 4184 designates belts. SPZ, SPA, SPB and SPC are the narrow sections, with groove datum widths of 8.5, 11, 14 and 19 mm.
Do belt drives need guards at work?
Yes. PUWER regulation 11 requires effective measures to prevent access to dangerous parts of machinery, starting with fixed guards enclosing them where practicable.
Sources and further reading
- The Electricity Safety, Quality and Continuity Regulations 2002, regulation 27, legislation.gov.uk. Declared frequency of 50 Hz and voltage of 230 V.
- The Provision and Use of Work Equipment Regulations 1998, regulation 11, legislation.gov.uk. Dangerous parts of machinery.
- Provision and Use of Work Equipment Regulations 1998 (PUWER), Health and Safety Executive.
- ISO 4184:1980 Classical and narrow V-belts: Lengths (sample pages), International Organization for Standardization (iTeh preview). Sections and datum length designation.
- Shigley's Mechanical Engineering Design, McGraw Hill. Table 17-2, belt geometry.
Open the Pulley and Belt Calculator
More Mechanical
Every tool in the Mechanical section, free and in your browser.
- Torque and Power Calculator
- Gear Ratio Calculator
- Pulley and Belt Calculator
- Bolt Torque Calculator
- Spring Calculator
- Stress and Strain Calculator
- Bearing Life Calculator
- Hydraulic Cylinder Calculator
- Tap Drill Size Calculator
- Speeds and Feeds Calculator
- ISO Fits & Tolerances Calculator
- Bolt Circle Calculator
- Shaft Torsion Calculator
- Shaft Diameter Calculator
- Shaft Key Size Calculator