United Kingdom version. Starts from a 4-pole motor at 1,450 rpm on the UK 50 Hz supply instead of the 1,750 rpm of a 60 Hz US motor, and covers PUWER guarding of belt drives. US version

Pulley and Belt Calculator (UK, 50 Hz Motors)

Pulley size, driven rpm, belt speed and belt length for drives on UK 50 Hz motors (about 1,450 rpm for 4-pole), with centre distance from a stock belt length.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Pulley and Belt Calculator?

The UK mains supply is declared at 50 hertz, so an induction motor here turns about 17% slower than the same motor on the 60 Hz supply in North America. A 4-pole motor has a synchronous speed of 1,500 rpm and a nameplate speed a little under that, commonly around 1,450 rpm; a 2-pole motor runs close to 2,900 rpm. Pulley charts copied from US manuals often assume 1,750 or 3,450 rpm, which is why a machine set up from one runs slow here.

This version starts from 1,450 rpm. A 100 mm motor pulley driving a 250 mm pulley turns it at 580 rpm, not the 700 rpm the US default gives. To get 700 rpm on a UK motor with the same driven pulley you need a 120.7 mm driver; pick the nearest stock pitch diameter and recheck the speed it gives.

Enter the nameplate speed of your own motor rather than the synchronous figure, add 1 to 3% slip for a V-belt, and use the belt length mode to find where the motor must sit for a stock belt.

  • Solves driver or driven diameter or speed, with optional slip
  • Exact open-belt length and the handbook approximation side by side
  • Centre distance from belt length, solved exactly and by the closed-form inverse
  • Wrap angle on both pulleys, belt speed in m/s and ft/min, crossed-belt length
  • Millimetres or inches with in-place conversion; copy and share
Read the guide: Belt Length and Pulley Speed Formulas, Derived and Checked

Updated

How to use the Pulley and Belt Calculator

  1. Choose millimetres or inches, then choose which of the four values to solve for.
  2. Enter the other three: driver diameter and rpm, driven diameter and rpm. Add a slip percentage for V or flat belts if you want the real driven speed.
  3. Pick Belt length from centres and enter the centre distance, or Centres from belt length and enter the belt's pitch length.
  4. Read the solved value, speed ratio, belt speed, belt length (exact and approximate) or centre distance, and the wrap angles.
  5. Watch the warnings: wrap below 120 degrees, overlapping pulleys, or belt speed above 30 m/s.

Worked examples

US pulley pair on a UK motor

Input

100 mm driver at 1,450 rpm, 250 mm driven, 500 mm centres

Output

Driven 580 rpm; belt 7.59 m/s; belt length 1,561.05 mm; wrap 162.7°

At 1,750 rpm the same pulleys give 700 rpm and 9.16 m/s. The ratio is unchanged; only the motor speed has dropped with the supply frequency.

Sizing a fan pulley for 960 rpm

Input

125 mm driver at 1,450 rpm, target 960 rpm, 450 mm centres; slip 0% and 2%

Output

Driven pulley 188.8 mm with no slip, 185.0 mm allowing 2% slip; belt about 1,395 mm

With a friction belt the driven pulley must be slightly smaller to reach the target speed. Choose the nearest stock pitch diameter and recheck.

2-pole motor with a 1,250 mm belt

Input

90 mm driver at 2,900 rpm, 180 mm driven, belt length 1,250 mm

Output

Driven 1,450 rpm; belt 13.7 m/s; centre distance 410.47 mm; wrap 167.4°

A 2 to 1 reduction from a 2-pole motor gives about the speed of a 4-pole motor shaft, with twice the torque at the driven shaft that the motor itself delivers, less belt losses.

Background and insight

For an open (uncrossed) belt the straight spans are tangent to both pulleys. With large diameter D, small diameter d and centre distance C, each span makes an angle φ = asin((D − d) / 2C) with the line of centres. The belt wraps π − 2φ radians of the small pulley and π + 2φ of the large one, so the exact pitch length is L = 2√(C² − ((D − d)/2)²) + π(D + d)/2 + (D − d)φ. This is the form in Shigley's Mechanical Engineering Design, Table 17-2.

Replacing the square root and the arcsine with the first terms of their series gives the approximation L ≈ 2C + π(D + d)/2 + (D − d)² / 4C found in Machinery's Handbook and most belt catalogues. For ordinary drives it is within a fraction of a millimetre: the default 100 and 250 mm pulleys at 500 mm centres give 1,561.05 mm exact and 1,561.03 mm approximate. The gap grows as the diameter difference approaches the centre distance, which is why the calculator shows both.

Belt makers rate drives using pitch diameters and pitch length, measured at the belt's neutral layer. For V-belts that is a little inside the sheave's outside diameter; for timing belts it is the tooth pitch line. Friction belts also creep, typically 1 to 3%, so the driven pulley runs slightly slower than the ideal ratio; timing belts do not slip.

Common use cases

  • Changing a machine speed

    Find the pulley size that gives a target spindle, fan or pump speed from a fixed motor speed.

  • Ordering a replacement belt

    Measure the pulleys and centre distance and get the pitch length to look up in a catalogue.

  • Laying out a new drive

    Work back from a stock belt length to the motor position, and check wrap angle before welding a base.

  • Checking belt speed

    Confirm the belt runs inside the manufacturer's speed limit and in its efficient range.

Tips and limitations

  • Read the full-load speed from the motor nameplate. Motors with the same pole count differ by tens of rpm with size and efficiency class, which matters for close speed targets.
  • Narrow wedge belts sold in the UK are labelled by section (SPZ, SPA, SPB, SPC) and length in millimetres, measured on the datum line of the belt; match both, and use the datum diameter of the pulley in the calculator.
  • If the motor runs from an inverter, output speed scales with frequency, so 40 Hz gives about 80% of the 50 Hz speed. Pulleys still set the ratio.
  • Allow motor travel either side of the calculated centre distance for fitting and tensioning the belt.

Sources and further reading

  1. The Electricity Safety, Quality and Continuity Regulations 2002, regulation 27, legislation.gov.uk. Declared supply frequency of 50 hertz, plus or minus 1%.
  2. The Provision and Use of Work Equipment Regulations 1998, regulation 11, legislation.gov.uk. Dangerous parts of machinery and the order of guarding measures.
  3. ISO 4184:1980 Classical and narrow V-belts: Lengths (sample pages), International Organization for Standardization (iTeh Standards preview). Sections Y to E and SPZ to SPC with groove datum widths; belts designated by section and datum length, e.g. SPA 1 250.

Frequently asked questions

Why does a machine from the US run slower on UK mains?

Induction motor speed follows supply frequency. On 50 Hz a 4-pole motor runs near 1,450 rpm instead of about 1,750 rpm on 60 Hz, so every driven pulley turns about 17% slower unless the pulleys are changed or an inverter is fitted.

What rpm does a 4-pole motor run at in the UK?

Synchronous speed is 120 x 50 / 4 = 1,500 rpm. Under load the rotor slips a little, so the nameplate shows a full-load speed just below 1,500 rpm. Use the nameplate value in the calculator.

How do I find the pulley size for a target speed on a 1,450 rpm motor?

Driven diameter = driver diameter x 1,450 / target rpm. For 960 rpm from a 125 mm driver that is 188.8 mm. Set Solve for to Driven dia. and the calculator does it, including slip.

Do belt drives need guarding under PUWER?

Yes. Regulation 11 of the Provision and Use of Work Equipment Regulations 1998 requires employers to prevent access to dangerous parts of machinery, with fixed guards first where practicable. The in-running nip where a belt meets its pulley is a typical dangerous part.

What do SPA or SPZ mean on a V-belt?

They are the narrow V-belt sections of ISO 4184, smallest SPZ through SPA, SPB and SPC, for grooves with datum widths of 8.5, 11, 14 and 19 mm. The number after the section is the datum length in millimetres, as in SPA 1250 or SPA 1600. The classical sections in the same standard are Y, Z, A, B, C, D and E.

Can I change speed with an inverter instead of new pulleys?

Often, within limits. Running a standard motor well below 50 Hz reduces its cooling fan speed, and running above 50 Hz reduces available torque, so check the motor and inverter data before relying on large speed changes.

Is there an in-depth guide to the Pulley and Belt Calculator?

Yes. “Belt Length and Pulley Speed Formulas, Derived and Checked” covers the background, how it works, common pitfalls and worked examples. Read the full guide.