United Kingdom version. Starts on an M12 class 8.8 bolt in newton metres, adds the low-strength class 4.6 for comparison, and notes the DVSA wheel-nut re-check rule. US version

Bolt Torque Calculator (UK, Metric in Nm)

Tightening torque in Nm and clamp load for M3 to M36 bolts in class 4.6, 5.6, 8.8, 10.9 and 12.9 to BS EN ISO 898-1, with nut factors and a full size chart.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Bolt Torque Calculator?

Most bolts bought in the UK are metric coarse thread, marked on the head with an ISO 898-1 property class (published here as BS EN ISO 898-1), and torque wrenches sold in Britain read in newton metres first. This version opens on an M12 class 8.8 bolt with dry threads: loaded to 75% of its proof load it needs 88.0 N·m. Change the class to 4.6, the lowest class in the list, and the same size needs only 34.1 N·m. Applying the 8.8 figure to a 4.6 bolt overloads it far past yield.

Older British machinery and classic cars may still carry UNC and UNF fasteners, which the calculator also covers with SAE Grade 5 and 8 values in lb·ft. Whitworth (BSW) and BSF threads are not in the thread list: their pitches and stress areas differ, so do not substitute the nearest metric or Unified size.

Where a vehicle or machine maker publishes a torque, that figure wins. This tool is for joints that come with a bolt class on the drawing but no tightening value, for writing a workshop torque chart in the lubricant you really use, and for checking whether a figure from a manual looks sensible.

  • Metric coarse M3 to M36, UNC and UNF 1/4 to 1-1/2 inch
  • ISO 898-1 classes 4.6, 5.6, 8.8, 10.9, 12.9 and SAE J429 Grades 5 and 8 with size-dependent proof stress
  • Nut factor presets from Shigley Table 8-15, or a custom K
  • Torque from target preload, or preload from a torque; percent of proof and yield shown
  • Full torque chart for the series, copy and share link
Read the guide: Bolt Tightening Torque and Preload: T = KFd in Practice

Updated

How to use the Bolt Torque Calculator

  1. Pick the thread series: metric coarse, UNC or UNF. The grade list switches between ISO property classes and SAE grades.
  2. Choose the size and the property class or grade marked on the bolt head.
  3. Set the thread condition. Use dry, finish unknown (K = 0.20) if you are unsure, or enter a measured K.
  4. Choose Torque for a target preload and enter the percentage of proof load, or Preload from a torque and enter the wrench setting.
  5. Read the torque, preload and bolt stress, and use the chart below for other sizes at the same settings.

Worked examples

M12 class 8.8 against class 4.6

Input

M12 x 1.75, dry (K = 0.20), 75% of proof load; class 8.8, then class 4.6

Output

Class 8.8: preload 36.7 kN, 88.0 N·m. Class 4.6: preload 14.2 kN, 34.1 N·m

The stress area is the same 84.3 mm² for both, but the proof stress drops from 580 MPa to 225 MPa. Read the head marking before you pick up the wrench.

M16 class 8.8, oiled versus dry

Input

M16 x 2, class 8.8, 75% of proof; K = 0.18 (lubricated) and K = 0.20 (dry)

Output

Preload 68.2 kN in both cases; 196.3 N·m oiled, 218.1 N·m dry

Oiling the threads lowers the torque needed for the same clamp force by about 10%. A dry-thread figure used on oiled bolts would push them towards yield.

M20 class 10.9 for a machine base

Input

M20 x 2.5, class 10.9, dry (K = 0.20), 75% of proof

Output

Proof load 203.2 kN; preload 152.4 kN; 609.5 N·m

At this size the scatter in friction matters more than the arithmetic: the same 609.5 N·m on a bolt with K = 0.15 would give about 203 kN, right at proof load. Large structural and machine joints are therefore tightened by a controlled method such as turn-of-nut or tension-indicating washers.

Background and insight

Proof load is the tensile force a bolt must carry without permanent set, and it is the usual basis for preload. It is the tensile stress area times the proof stress. ISO 898-1 gives proof stresses of 580 MPa for class 8.8 up to M16 (600 MPa above), 830 MPa for 10.9 and 970 MPa for 12.9. SAE J429 gives 85 ksi for Grade 5 from 1/4 to 1 inch (74 ksi from over 1 to 1-1/2 inch) and 120 ksi for Grade 8. Stress areas come from the thread geometry: As = π/4 (d − 0.9382P)² for ISO metric threads and At = 0.7854 (D − 0.9743/n)² for Unified threads in ASME B1.1, which reproduce the tabulated 58.0 mm² for M10 and 0.1419 in² for 1/2-13.

The nut factor K is not a friction coefficient; it lumps thread friction, underhead friction and thread geometry into one empirical number. Shigley's Mechanical Engineering Design (Table 8-15, from Bowman's Fastener Facts) lists 0.30 for non-plated black finish, 0.20 for zinc-plated, 0.18 for lubricated, 0.16 for cadmium-plated and 0.12 with anti-seize compound, and suggests K = 0.20 when the condition is unknown. Shigley recommends preload of 75% of proof load for connections that will be reused and 90% for permanent ones.

Because friction varies, torque is an imprecise way to set preload. Two bolts tightened to the same torque can differ in clamp force by 25% or more. Where that matters, engineers use turn-of-nut, direct tension indicators, ultrasonic measurement or torque-angle methods, and VDI 2230 for a full joint analysis.

Common use cases

  • Machine assembly

    Set wrench values for flanges, brackets and covers when the drawing gives a bolt grade but no torque.

  • Automotive and equipment repair

    Check whether a torque from a manual is in a sensible range for the bolt size and grade fitted.

  • Writing a torque table

    Generate a chart for a whole thread series at the lubrication and preload your shop actually uses.

  • Diagnosing loose or broken bolts

    Back out the preload a given torque produced to see whether a joint was under- or over-tightened.

Tips and limitations

  • The first number of the class times 100 is the nominal tensile strength in MPa; the second, divided by 10, is the ratio of yield to tensile. So 8.8 means 800 MPa tensile and 640 MPa yield, and 4.6 means 400 MPa and 240 MPa.
  • Copper grease and other anti-seize compounds cut friction sharply. If a manual gives a dry torque, do not apply it to greased threads; use the anti-seize preset to see the extra preload it would cause.
  • Treat an unmarked bolt as unknown strength: do not use it in a structural or safety-critical joint. Class 4.6 is the lowest class the calculator offers, not a guaranteed minimum.
  • After refitting road wheels on commercial vehicles, DVSA guidance is to re-check wheel-nut torque after 30 minutes standing or 40 to 80 km of driving, and to record the check.

Sources and further reading

  1. Guide to maintaining roadworthiness: commercial goods and passenger carrying vehicles, Driver and Vehicle Standards Agency (GOV.UK). Section 5.1: re-check wheel-nut torque after 30 minutes standing or 40 to 80 km, and record every re-torque check.
  2. ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel, Part 1, International Organization for Standardization. Property classes 4.6 to 12.9 and their proof stresses; published in the UK as BS EN ISO 898-1.
  3. IS 1367 (Part 3):2002 Technical supply conditions for threaded steel fasteners, Part 3: Mechanical properties of fasteners made of carbon steel and alloy steel, bolts, screws and studs, Bureau of Indian Standards (Public.Resource.Org copy). Identical with ISO 898-1:1999; Table 3 lists the proof stresses used here (225, 580/600, 830 and 970 N/mm²).
  4. Fastener Design Manual (NASA RP-1228), NASA. Torque, friction and preload scatter.

Frequently asked questions

What torque does an M12 8.8 bolt need in Nm?

About 88 N·m with dry or zinc-plated threads (K = 0.20) when loaded to 75% of proof load, which gives 36.7 kN of clamp force. Lubricated threads reach the same clamp force at about 79 N·m with K = 0.18.

What does 8.8 stamped on a bolt head mean?

It is the BS EN ISO 898-1 property class. 8 x 100 gives the nominal tensile strength (800 MPa) and 0.8 of that is the nominal yield (640 MPa). Class 10.9 is 1,000 MPa tensile with 90% yield, and 12.9 is the strongest common class.

Is a grade 4.6 bolt strong enough to take an 8.8 torque?

No. Its proof stress is 225 MPa against 580 MPa for 8.8, so the 8.8 torque would stretch it well past yield. Use the 4.6 setting, or fit 8.8 bolts if the joint needs the higher clamp force.

When should wheel nuts be re-torqued after a wheel change?

For goods vehicles and buses, the DVSA Guide to Maintaining Roadworthiness repeats the industry code of practice: check the torque after the vehicle has stood for 30 minutes or after 40 to 80 km (25 to 50 miles), and record every re-torque check. For cars, follow the maker's figure and procedure; this chart is not a wheel-nut table.

Does the calculator cover Whitworth or BSF bolts?

No. It covers ISO metric coarse and Unified UNC and UNF threads. Whitworth and BSF threads have their own pitches and form, so take torque values from the machine maker or a BSW table.

Should I use the torque in a workshop manual or this calculator?

Use the manual for that vehicle. Maker figures allow for the actual joint, gasket and fastener finish. The calculator is for joints with no published value and for checking that a figure is in a sensible range for the bolt size and class.

Is there an in-depth guide to the Bolt Torque Calculator?

Yes. “Bolt Tightening Torque and Preload: T = KFd in Practice” covers the background, how it works, common pitfalls and worked examples. Read the full guide.