United Kingdom version. Adds the British 55° threads still met in UK workshops: BSP parallel (G) pipe threads to ISO 228-1 and BSW and BSF to BS 84, with metric drills and UK "tapping drill" wording. US version

Tapping Drill Size Calculator (UK)

Tapping drill sizes for G (BSPP) pipe threads, BSW and BSF Whitworth threads and ISO metric, with the thread percentage each metric drill really leaves.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Tap Drill Size Calculator?

Most new UK work is ISO metric, but two British thread families refuse to go away. BSP parallel threads, marked G 1/4, G 1/2 and so on, are pipe threads that seal at a face rather than on the thread. BSW and BSF Whitworth threads remain in use on vintage machinery and in restoration work. Both use a 55° flank angle, not the 60° of metric and UNC, so this version carries them as their own thread system with the correct thread depth of 0.640327 × pitch.

The awkward one is BSP. A G 1/4 thread is not a quarter of an inch across: the size is the old nominal bore of the pipe, and the major diameter is 13.157 mm. You cannot work out its tapping drill from the name, which is why charts exist and why they disagree. For G 1/4 at 75% engagement the calculator gives 11.87 mm, so an 11.9 mm drill (73.4%). The commonly quoted 11.8 mm drill leaves 79.3%, and the 11.5 mm figure on some charts leaves 96.8%, close to full depth.

Pick "BSW / BSF / BSP" under thread system, choose the size, and the tool shows the nearest metric drill, the thread percentage it gives, the basic minor diameter (the 100% hole) and a chart for the whole series. Metric threads are still there under "Metric (ISO)": an M10 tapping drill is 8.5 mm at 77.0%.

  • Metric coarse and fine threads from M1.6 to M36 and UNC/UNF from #0 to 1-1/2 inch, plus custom threads
  • British BSW, BSF and BSP (G) parallel threads with the Whitworth 55° formula
  • Cutting and form tap formulas with any percent of thread
  • Nearest metric, fractional, number or letter drill and the real thread percentage it gives
  • Options table either side of the target, a full chart for the chosen series and a drill check field
  • Formula panel, copy and share link; runs entirely in your browser
Read the guide: Tap Drill Sizes and Percent of Thread: Choosing the Right Hole

Updated

How to use the Tap Drill Size Calculator

  1. Under thread system choose "BSW / BSF / BSP". Whitworth-form threads are cut-tapped, so the tap type is fixed.
  2. Pick the size: BSW coarse and BSF fine from 1/8 or 3/16 inch to 1 inch, or G pipe threads from 1/8 to 1.
  3. Leave the percent of thread at 75% for bolts and studs; for a pipe port, raise it towards 80 to 85% if you want to match the usual chart drills.
  4. Keep the drill series on Auto for metric jobber drills, or choose "Fractional, number, letter" if you only have an imperial set.
  5. Type the drill already in the chuck into the check field to see the engagement it would leave.

Worked examples

G 1/4 port in an aluminium manifold

Input

G 1/4 BSPP (19 TPI), cutting tap, 75% thread, metric drills

Output

Theoretical 11.873 mm; 11.9 mm gives 73.4%; the chart 11.8 mm gives 79.3%

The pitch is 25.4 / 19 = 1.337 mm and the basic minor diameter is 11.445 mm. G threads seal on a bonded washer or O-ring at the face, not on the thread, so either drill works; 11.8 mm gives a little more grip in soft alloy.

1/4 inch BSW for a replacement stud

Input

1/4" BSW (20 TPI), 75% thread, metric drills

Output

Theoretical 5.130 mm; 5.1 mm gives 76.9%

1/4 BSW and 1/4-20 UNC share a 1.27 mm pitch, and with the 60° formula the target would be 5.113 mm, so the drill hardly changes. The flank angle does: a UNC tap leaves a 60° groove that a 55° Whitworth bolt fits loosely, bearing on only part of each flank, so use a BSW tap.

1/2 inch BSW and the drill on the rack

Input

1/2" BSW (12 TPI), 75% thread; check a 10.5 mm drill

Output

10.7 mm gives 73.8%; a 10.5 mm drill gives 81.2%

Coarse Whitworth has a deep thread (2.71 mm on diameter at 12 TPI), so a 0.2 mm smaller drill adds about 7 points of engagement and a noticeably stiffer tap. 10.7 mm is the easier choice in steel.

G 1/2 and a chart that drills under the minor diameter

Input

G 1/2 BSPP (14 TPI); check 18.6 mm and 19 mm

Output

18.6 mm gives over 100%; 19 mm gives 84.1%

The basic minor diameter of G 1/2 is 18.631 mm, so an 18.6 mm drill is a fraction under it and the tap trims the bore to size. Charts for BSP work much closer to full depth than bolt-thread charts do, which is why their numbers look small next to a 75% calculation.

Background and insight

The percent-of-thread convention measures how much of the basic thread depth the tapped hole leaves for the screw to bear on. For 60° unified and ISO metric threads the basic double height used for this purpose is 1.299 × pitch, so the cutting tap drill formula is drill = D − 0.01299 × %thread × P, with P in millimetres or as 1/TPI in inches. Machinery's Handbook gives this form and the inverse, %thread = (D − drill) / (0.01299 × P).

Tap makers commonly point out that a 75% thread is only a few percent weaker than a full thread in steel, because the bolt or the external thread usually fails first, yet a 100% thread takes roughly three times the torque to tap. That is why charts settle on 75% for general work, 60 to 65% for tough or work-hardening alloys, and higher only for thin sections where every bit of engagement counts.

Form taps do not cut; they push material into the thread shape, so the hole must be larger. Tap makers and Machinery's Handbook give drill = D − 0.0068 × %thread × P for forming, with 60 to 70% thread typical. A 1/4-20 form tap at 65% calls for 0.2279 in, which is a #1 drill. Always check the tap maker's chart, since some coatings and alloys move the ideal hole by a few hundredths of a millimetre.

Common use cases

  • Drilling and tapping on the shop floor

    Find the tap drill when the chart drill is missing and see what the closest drill on the rack will give you.

  • Hard or gummy materials

    Drop to 60 to 65% thread in stainless, titanium or Inconel to cut tapping torque and tap breakage.

  • Form tapping

    Get the larger pilot hole a thread-forming tap needs in aluminium, copper and mild steel.

  • CAD and drawings

    Pick a hole size for a tapped hole callout and record the thread engagement it produces.

Tips and limitations

  • G (BSPP, ISO 228-1) is parallel and seals at the face; R and Rp (BSPT, ISO 7-1) seal on the thread. A taper thread needs a taper pipe tap and its own drill size, so do not use these parallel figures for it.
  • BSF is finer than BSW at the same diameter (1/4 BSF is 26 TPI against 20 for BSW), so check the pitch with a 55° gauge before choosing a tap. A metric 60° pitch gauge will not seat properly on either.
  • BA threads (47.5°, on old instruments and electrical gear) are a different form again and are not in this calculator.
  • Drills cut slightly oversize in steel, so the real engagement is usually a few points under the figure shown.

Sources and further reading

  1. Pipework: BSP threads, dcldesign code. Pitch, major and minor diameters and tapping drills for G and R pipe threads; ISO 7 versus ISO 228.
  2. Whitworth coarse thread (BSW, BS 84), gewinde-normen.de. Threads per inch and major diameters for BSW sizes; 55° flank angle.
  3. Whitworth fine thread (BSF, BS 84), gewinde-normen.de. Threads per inch and major diameters for BSF sizes.
  4. British Standard Whitworth, Wikipedia. The 55° form, thread depth 0.640327 × pitch, BSP to ISO 228 using the Whitworth form, and continued use in restoration and vintage machinery.
  5. Tapping drill size chart for thread cutting taps, AIMS Industrial Supplies. A supplier chart: drills of 8.8, 11.8, 15.0 and 18.6 mm for 1/8 to 1/2 inch BSP.

Frequently asked questions

What is the tapping drill for 1/4 BSP?

For a G 1/4 (BSPP, 19 TPI) parallel thread, 11.8 mm is the usual chart drill and leaves 79.3% thread; 11.9 mm is the 75% answer at 73.4%. Some charts list 11.5 mm, which is almost the 11.445 mm basic minor diameter and leaves about 97%.

What size drill do I need for 1/4 BSW?

5.1 mm. It leaves 76.9% of the 55° Whitworth thread, right in the normal band. A 5.2 mm drill drops it to about 71%, still fine in mild steel and easier on a small tap.

Can I use a UNC tap on a BSW thread?

Only as a bodge. 1/4-20 UNC and 1/4 BSW have the same pitch, but UNC is 60° with flat crests and BSW is 55° with rounded crests, so the bolt bears on a fraction of the flank. Sizes such as 1/2 inch also differ in pitch (13 TPI UNC against 12 TPI BSW) and will cross-thread.

Is BSP the same as G thread and BSPP?

Yes for parallel threads: BSPP, "G" and ISO 228-1 all describe the same 55° parallel pipe thread, which seals with a washer or O-ring. BSPT, marked R (external) and Rp or Rc (internal) under ISO 7-1, is the pressure-tight version that seals on the thread.

Why do BSP tapping drill charts disagree?

Each chart picks its own engagement. Working back from the drills they list, G 1/4 at 11.8 mm is about 79%, G 3/8 at 15.0 mm about 97% and G 1/2 at 18.6 mm slightly over 100%. The calculator shows the percentage for any drill so you can see which choice you are making.

What is the tapping drill for M10?

8.5 mm for M10 x 1.5 coarse, which gives 77.0% thread with a cutting tap. For M8 x 1.25 it is 6.8 mm (73.9%) and for M12 x 1.75 either 10.2 mm (79.2%) or 10.3 mm (74.8%).

Is there an in-depth guide to the Tap Drill Size Calculator?

Yes. “Tap Drill Sizes and Percent of Thread: Choosing the Right Hole” covers the background, how it works, common pitfalls and worked examples. Read the full guide.