India version. Starts with 12 mm TMT bars in 12 m lengths, uses the IS 1786 nominal masses and tolerances, ISMB sections from IS 808:1989 and prices in rupees per kg. US version
Steel Weight Calculator (India)
TMT bar weight per metre and per bundle from IS 1786 sizes (D²/162), ISMB and other sections, plates and pipes in kg, with the IS 1786 mass tolerance and price in ₹.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Steel Weight Calculator?
On Indian sites reinforcement is bought by weight and fixed by count, so the everyday question is how many kilograms a given number of TMT bars weighs, or how many bars make a tonne. The quick rule is D²/162 kg per metre with D in millimetres: a 12 mm bar is 144/162 = 0.889 kg/m. That rule is simply the bar area at 7,850 kg/m³, which is also how IS 1786 defines nominal mass (0.00785 kg per mm² per metre), and it is what this calculator works out exactly: 0.888 kg/m for 12 mm, 10.65 kg for one 12 m bar and 1,065 kg for a bundle of 100.
IS 1786 lists the nominal masses (Table 1) and how far a delivery may stray from them (Table 2): ±7% on a batch of bars up to 10 mm, ±5% for sizes over 10 mm up to 16 mm, and ±3% above 16 mm. Weighing a bundle and comparing it with the calculated figure is the simplest site check that you have received full-size bars. TMT bars sold in India must conform to IS 1786 and carry the BIS mark, as the standard is covered by the Ministry of Steel's quality control orders.
For structural steel, enter ISMB, ISMC or ISA sizes with their IS 808 dimensions. The tool leaves out the root fillets of rolled sections, so ISMB 200 (IS 808:1989 Table 2.1: 200 x 100 mm, 5.7 mm web, 10.0 mm flange) comes out at 23.75 kg/m against the 24.2 kg/m in the table; use the table figure for billing and the calculator for odd sections, plates and pipes.
- Plate, flat, round, square and hex bar, round tube, SHS, RHS, angle, channel and I-beam
- EN 10219 and EN 10210 corner radii for hollow sections, or sharp corners
- Weight per metre and per foot, per piece and in total, in kg and lb
- Density presets for carbon and stainless steel, cast iron, aluminium, copper, brass and titanium, all editable
- Comparison table for every material, surface area for coating, optional cost
Updated
How to use the Steel Weight Calculator
- Choose metric (mm, m, kg) or imperial (in, ft, lb). Switching converts the sizes you already entered.
- Pick the shape and enter its dimensions. Tubes need the outside size and the wall thickness.
- For square or rectangular tube, choose cold-formed, hot-finished or sharp corners.
- Enter the length of each piece and the quantity, then pick the material or type a density.
- Read the total, the weight of each piece, the weight per metre or foot and the surface area; add a price per kg or lb for a cost.
Worked examples
100 bars of 12 mm TMT, 12 m long
Input
Round bar 12 mm, 12 m, quantity 100
Output
0.888 kg/m; 10.65 kg per bar; 1,065 kg (1.07 tonnes)
About 94 bars of 12 mm make a tonne. At a rate in ₹ per kg the cost box multiplies this total directly.
Checking a bundle of 8 mm against IS 1786
Input
Round bar 8 mm, 12 m, quantity 50
Output
0.395 kg/m; 236.75 kg nominal
With the ±7% batch tolerance for bars up to 10 mm, an acceptable bundle weighs between about 220 kg and 253 kg. Lighter than that and the bars are undersize.
ISMB 200, 6 m
Input
I-beam 200 x 100 mm, web 5.7 mm, flange 10.0 mm, 6 m
Output
23.75 kg/m; 142.5 kg
IS 808:1989 Table 2.1 gives 24.2 kg/m (145.2 kg for 6 m) because it includes the root fillets and tapered flanges. The 2% gap is normal for this calculator on rolled sections.
Background and insight
Weight is simply cross-section area times length times density. The area formulas are exact for the idealised shapes: a round tube is π(D − t)t, an angle is t(a + b − t), and a hollow section with rounded corners is 2t(B + H − 2t) − (4 − π)(ro² − ri²). The ASME B36.10 pipe weight formula, 10.69(D − t)t in lb/ft with inches, is the same equation with the steel density folded in.
Carbon steel is taken as 7,850 kg/m³ (0.2836 lb/in³), the value EN 10025 and most section tables use. Stainless grades are heavier: EN 10088-1 gives 7,900 kg/m³ for 1.4301 (304) and 8,000 kg/m³ for 1.4401 (316). Aluminium alloys are about 2,700 kg/m³, copper C11000 about 8,890 kg/m³ and cartridge brass about 8,530 kg/m³. All of these are typical values at room temperature; enter your supplier's figure if it differs.
Real stock is never exactly nominal. Mill tolerances on plate thickness and bar diameter (EN 10029, ASTM A6) allow a few percent either way, and rolled beams, channels and angles have root fillets that add a little area. Use the theoretical weight for estimating and quoting, and the certified weight on the delivery note for lifting plans.
Common use cases
Quoting fabrication jobs
Total the weight of plates, tubes and sections in a frame to price material and galvanising.
Lifting and transport
Check that a bundle of bar or a stack of plate is within a crane, forklift or trailer limit.
Comparing materials
See how much an aluminium or stainless version of the same part weighs before redesigning.
Estimating dead load
Get kg per metre of a beam or rail to add self-weight to a structural load calculation.
Tips and limitations
- Bar weight per metre for common sizes: 8 mm 0.395, 10 mm 0.617, 12 mm 0.888, 16 mm 1.58, 20 mm 2.47, 25 mm 3.85 and 32 mm 6.31 kg (IS 1786 Table 1).
- Steel is usually quoted per tonne or per kg plus GST; enter the per kg rate in ₹ to get the material cost of a bar schedule.
- Standard TMT length is 12 m, so a bar bending schedule converts quickly from metres to bars and kilograms.
- Check the grade (Fe 415, Fe 500, Fe 500D, Fe 550D and so on) and the BIS standard mark on the bundle tag before accepting a delivery.
Sources and further reading
- IS 1786:2008 High strength deformed steel bars and wires for concrete reinforcement, Bureau of Indian Standards (public copy). Table 1 nominal cross-sectional area and mass; Table 2 tolerances on nominal mass; 7.2.1 density 0.00785 kg/mm² per metre.
- IS 808:1989 Dimensions for hot rolled steel beam, column, channel and angle sections, Bureau of Indian Standards (public copy). Table 2.1 medium weight beams: ISMB 200 at 24.2 kg/m, 200 x 100 mm, 5.7 mm web, 10.0 mm flange.
- Lok Sabha unstarred question 3149: Quality control orders for steel products (6 August 2018), Ministry of Steel, Government of India. Steel products, including IS 1786 bars and IS 2062 structural steel, may not be sold unless they bear the BIS mark.
- Handout on building materials, Bureau of Indian Standards. Indian Standards for reinforcing bars (IS 1786) and structural steel (IS 2062).
Frequently asked questions
What is the formula for TMT bar weight per metre?
D²/162, with D in millimetres, gives kg per metre. It comes from π/4 × D² × 7,850 / 10⁶, so the exact divisor is 162.2. The calculator uses the exact area, which is why 12 mm shows 0.888 rather than 0.889 kg/m.
How many 12 mm bars are there in one tonne?
About 94 bars of 12 m length. One bar weighs 0.888 × 12 = 10.65 kg, and 1,000 / 10.65 = 93.9.
How much weight variation is allowed in TMT bars?
IS 1786 Table 2 allows ±7% on a batch for sizes up to 10 mm, ±5% over 10 mm up to 16 mm and ±3% over 16 mm, with slightly wider minus limits for an individual sample.
Is BIS certification compulsory for TMT bars?
Yes. IS 1786 is one of the steel standards notified under the Ministry of Steel's quality control orders, which bar the sale of covered products without the BIS standard mark.
What is the weight of ISMB 200 per metre?
IS 808:1989 Table 2.1 lists 24.2 kg/m for ISMB 200 (200 x 100 mm, 5.7 mm web, 10.0 mm flange). The calculator gives 23.75 kg/m from those dimensions because it ignores the root fillets, so use 24.2 for estimates and billing, or the figure in your supplier's current section table.
How do I calculate the weight of an MS plate?
Each millimetre of thickness weighs 7.85 kg per square metre. A 2,500 × 1,250 mm plate of 10 mm is 245 kg; choose plate, enter the width, thickness and length, and add a rate per kg for the cost.
Is there an in-depth guide to the Steel Weight Calculator?
Yes. “Steel Weight Formulas for Plate, Bar, Pipe and Sections (kg/m and lb/ft)” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.