Pakistan version. Metric, in tonnes, opening on 3 mm structural plate at 550 N/mm², the upper tensile limit of PS 4798, Pakistan's carbon structural steel standard. US version
Press Brake Tonnage Calculator (Tonnes, MS Sheet and Plate)
Bending force in tonnes and kN for MS sheet and PS 4798 plate from thickness in mm or SWG, bend length and V-die, planned for the top of the tensile range.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Press Brake Tonnage Calculator?
Bending force rises in step with the steel's tensile strength, so the strength you assume decides whether a job fits the brake. PS 4798, Pakistan's standard for carbon structural steel, sets the tensile strength of plates, shapes and bars at 400 to 550 N/mm² with a minimum yield of 250 N/mm². This version plans for the top of that range: a 3 mm plate bent along 2440 mm in a 24 mm die (8 x T) needs 82.0 tonnes at 550 N/mm², against 59.6 tonnes at 400 N/mm².
That 37.5% spread is the reason to read the mill test certificate. If it shows a tensile strength near the minimum, enter it as a custom value and the force drops in proportion; if you have no certificate, size the machine for 550 N/mm².
Thin sheet works the same way. An 18 SWG (1.219 mm) sheet bent over 2440 mm in the 8 x T die of 9.75 mm needs about 25.1 tonnes with the mild steel preset of 414 N/mm².
- Air bending, bottoming and coining force
- US tons, metric tonnes and kN, per length and in total
- Material presets by tensile strength or custom UTS
- Inside radius and minimum flange rules for the chosen die
- Die opening comparison table and press capacity check
Updated
How to use the Press Brake Tonnage Calculator
- Keep metric units and enter the thickness in mm (for gauges, use the mm value: 16 SWG is 1.626 mm, 18 SWG 1.219 mm).
- Enter the bend length in mm; a full 8 ft sheet is 2440 mm.
- Leave the die on the 8 x T rule, or switch to "My die" for the V opening you have.
- For PS 4798 plate keep "Custom tensile strength" at 550 N/mm², or enter the figure from the test certificate; for thin sheet the mild steel preset is a fair start.
- Enter the brake's capacity in tonnes to see the load as a percentage.
Worked examples
3 mm plate, 8 ft bend, both ends of PS 4798
Input
T 3 mm, V 24 mm (8 x T), 2,440 mm, air bending, UTS 550 then 400 N/mm²
Output
82.0 t (803.8 kN, 33.6 t/m) at 550; 59.6 t (584.6 kN, 24.4 t/m) at 400
An 80 tonne brake would cope with soft plate and stall on hard plate from the same standard. The inside radius is about 3.84 mm and the minimum flange about 16.8 mm in either case.
18 SWG sheet over its full length
Input
T 1.219 mm (18 SWG), V 9.75 mm, 2,440 mm, mild steel preset 414 N/mm²
Output
25.1 t total, 10.3 t/m
Light work for most brakes. If the sheet is actually US 18 gauge (1.214 mm) the force is almost the same.
10 mm plate, 1.5 m bend, 100 mm die
Input
T 10 mm, V 100 mm (10 x T), 1,500 mm, UTS 550 then 400 N/mm²
Output
134.4 t (89.6 t/m) at 550; 97.7 t (65.1 t/m) at 400
A 100 tonne brake is only enough if the certificate shows plate near the bottom of the range, and even then with almost no margin.
6 mm plate, full 8 ft, 50 mm die
Input
T 6 mm, V 50 mm, 2,440 mm, UTS 550 N/mm²
Output
157.4 t total, 64.5 t/m
Check the tooling rating in tonnes per metre as well as the machine: 64.5 t/m is beyond many standard punches and dies.
Background and insight
The working formula in tooling catalogues and press makers’ charts is tons per foot = 575 x T² / V, with T and V in inches, for a 90° air bend in mild steel of 60,000 psi tensile strength (AISI 1035 cold-rolled is the usual baseline). Force rises with the square of thickness, because both the bending moment and the section that resists it scale with T, and falls with the die opening, because a wider die gives the punch more leverage. Other materials are scaled by their tensile strength divided by 60 ksi.
In metric units the same relation is about 1.6 x UTS x T² / V in kN per metre, with UTS in MPa and T and V in millimetres. European and Asian brake makers often publish a version with a constant of 1.42 and a 450 MPa baseline, which gives a few percent less; both are rules of thumb for 90° bends and should be checked against the chart for your press.
Air bending touches the sheet at only three points, so the force is low and the radius is set by the die, roughly 15 to 17% of V in mild steel, 20 to 22% in 304 stainless and 13 to 15% in 5052-H32 aluminium (Steve Benson’s 20% rule in The Fabricator; some of his columns put 5052-H32 nearer 11 to 13%, so confirm with a test bend). The calculator uses the middle of each range. Bottoming presses the sheet into the die and needs around five times the air-bend force; coining drives the punch tip into the material and needs ten times or more, which is why it is rarely used on modern brakes.
Common use cases
Checking a job against the press
Make sure the total force and the force per metre stay inside the press and tooling ratings before setting up.
Choosing a V-die
Balance force against inside radius and minimum flange length when picking the die opening.
Design for manufacture
Check that flange lengths and radii on a drawing can actually be formed on the available tooling.
Quoting thicker work
Find out quickly whether a plate job needs a bigger brake or a subcontractor.
Tips and limitations
- Keep V between about 6 and 12 times the thickness; a narrower die raises the force and the risk of cracking the outside of the bend.
- Bottoming needs about five times, and coining about ten times, the air-bending force, so stay with air bending on plate.
- Halving the bend length halves the total force, but the tonnes per metre on the punch and die stay the same.
Sources and further reading
- PS 4798:2017 (Rev) Carbon Structural Steel, Pakistan Standards and Quality Control Authority (PSQCA). Based on ASTM A36/A36M-14; covers plates, shapes and bars. Table 2: tensile strength 400 to 550 MPa (58 to 80 ksi), minimum yield point 250 MPa (36 ksi).
- List of compulsory items to meet Pakistan Standards, Pakistan Standards and Quality Control Authority (PSQCA). Includes PS 4798 Structural Steel, PS-ISO 3573 Hot-Rolled Carbon Steel Sheet and PS-ISO 3574 Cold Reduced Carbon Steel Sheet of commercial and drawing qualities.
- Standard wire gauge, Wikipedia. Table of Imperial Standard Wire Gauge sizes 1 to 30 in inches and mm.
Frequently asked questions
How many tonnes does it take to bend 3 mm plate 8 ft long?
In a 24 mm die, about 59.6 tonnes at 400 N/mm² tensile strength and 82.0 tonnes at 550 N/mm², the two ends of the PS 4798 range.
What tensile strength should I use for PS 4798 or A36 plate?
PS 4798 Table 2 gives 400 to 550 N/mm² (58 to 80 ksi) for plates, shapes and bars; the standard is based on ASTM A36/A36M-14. Use the value on the mill test certificate; without one, plan for 550.
Can a 100 tonne press brake bend 10 mm plate?
Over 1.5 m in a 100 mm die it needs 97.7 tonnes at 400 N/mm² and 134.4 tonnes at 550 N/mm². Shorten the bend, widen the die, or use a bigger brake unless the certificate shows soft plate.
What V-die opening should I use?
The calculator uses 8 x the thickness below 12.7 mm and 10 x at or above it, the common starting rule. A wider die lowers the force but gives a larger inside radius and needs a longer flange.
How do I convert press brake tonnes to kN?
Multiply metric tonnes by 9.807. The 82.0 tonne bend above is 803.8 kN. The calculator also shows US tons for brakes rated that way.
Is there an in-depth guide to the Press Brake Tonnage Calculator?
Yes. “Press Brake Tonnage, V-Die Width and the Air-Bent Radius” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.