Pakistan version. Starts on a 2440 x 1220 mm sheet in 20 SWG with the weight in kg, and works PS 4798 structural plate and PS-ISO cold-reduced sheet examples. US version
Steel Sheet and Plate Weight Calculator (kg, SWG and mm)
Weight of MS, GI, stainless or aluminium sheet and plate in kg from its size in mm and thickness or SWG gauge, with sheet counts and bolt holes taken off.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Sheet Metal Weight Calculator?
Steel sheet and plate are priced and loaded by weight, and the weight follows from the thickness. This version opens on a 2440 x 1220 mm (8 x 4 ft) mild steel sheet in 20 SWG, which is 0.914 mm thick: it weighs 21.37 kg, or 7.18 kg per square metre.
Check which gauge table a quotation uses. On the same 2440 x 1220 mm sheet, 22 SWG (0.711 mm) weighs 16.62 kg and the US 22 gauge (0.759 mm) 17.75 kg, a difference of 1.13 kg a sheet. The calculator has both tables; if the supplier gives the thickness in mm, use that instead.
For heavier work, PS 4798 Carbon Structural Steel, revised by PSQCA in 2017 and based on ASTM A36, covers plates, shapes and bars, and PSQCA lists it among the items that must meet Pakistan Standards. A 10 mm plate 1500 x 6000 mm weighs 706.5 kg, or 78.5 kg/m² at the calculator's 7,850 kg/m³.
- Ten material presets with typical published densities, plus custom density
- Thickness by value or by gauge from five gauge tables, including British SWG
- Round holes and rectangular cut-outs subtracted
- Weight per piece, batch total, kg/m² and lb/ft²
- Same-size weight in every other material, copy and share link
Updated
How to use the Sheet Metal Weight Calculator
- Keep metric units and enter the length and width in mm.
- For sheet, choose "Gauge number", pick the SWG table and the gauge; for plate, choose a thickness in mm.
- Pick mild steel for MS, GI base steel, PS-ISO sheet and PS 4798 plate; stainless, aluminium, copper and brass have their own densities.
- Enter the number of pieces, and any round holes or rectangular cut-outs to take off.
Worked examples
8 x 4 ft sheet, 20 SWG
Input
2440 x 1220 mm, 20 SWG (0.914 mm), mild steel 7,850 kg/m³
Output
21.37 kg per sheet, 7.18 kg/m² over 2.977 m²
Multiply by the number of sheets in a bundle to check a delivery against the weighbridge slip.
Same size in 22 gauge, two tables
Input
2440 x 1220 mm, 22 SWG (0.711 mm) against US 22 gauge (0.759 mm)
Output
16.62 kg against 17.75 kg per sheet
On 100 sheets the gap is 113 kg, enough to matter when sheet is quoted per kg.
Cold-reduced sheet for panels, 25 sheets
Input
2500 x 1250 x 1.0 mm, mild steel, quantity 25
Output
24.53 kg each, 613.3 kg in total
Cold-reduced carbon steel sheet comes under PS-ISO 3574 on PSQCA's compulsory list; order it by mm thickness.
Base plate with four bolt holes
Input
400 x 400 x 12 mm PS 4798 plate, four 22 mm holes
Output
14.93 kg each (15.07 kg before the holes)
Each 22 mm hole removes about 36 g. On a long run of base plates the holes add up, but the blank you buy is still the full square.
Background and insight
The default densities are typical published values: 7,850 kg/m³ for carbon steel (the value used throughout EN 1993 and most steel tables), 7,930 kg/m³ for 304 stainless, 2,680 kg/m³ for 5052 aluminium, 2,700 kg/m³ for 6061, 8,890 kg/m³ for C110 copper and 8,530 kg/m³ for C260 cartridge brass, the last two from Copper Development Association data. Alloys vary by a percent or so, so a custom density is available.
Steel sheet gauges carry a built-in weight. The Manufacturers’ Standard Gauge was defined from weight, at 41.82 lb per square foot per inch of thickness, which corresponds to about 8,030 kg/m³. That is why a nominal 16 gauge sheet is listed in old tables at 2.5 lb/ft² while 0.0598 in at 7,850 kg/m³ comes to 2.44 lb/ft². The calculator uses the density you pick, so expect results about 2% below the traditional gauge weight tables for steel.
Real sheet is rarely exactly nominal. Mills roll to a thickness tolerance (ASTM A568 for carbon steel sheet, ASTM A480 for stainless) and sheets tend to be thinner at the edges than in the middle. For shipping and lifting, round up; for costing by weight, ask the supplier whether they invoice on theoretical or actual weight.
Common use cases
Freight and handling
Know the weight of a bundle before booking a truck or choosing a lifting clamp or forklift.
Material costing
Convert a price per kilogram or pound into a price per sheet or per part.
Structural and enclosure design
Estimate the dead weight of cladding, guards, ducts and panels for supports and fixings.
Comparing materials
See how much an aluminium or stainless version of a steel part would weigh before redesigning it.
Tips and limitations
- Quick rule for steel: kg/m² = thickness in mm x 7.85. One tonne of 10 mm plate covers about 12.7 m².
- Theoretical weight, as here, assumes the nominal thickness. Sheet rolled near its lower tolerance weighs less on the scale.
- For galvanised sheet the calculator weighs the steel at the thickness you enter; the zinc coating adds the mass per square metre stated on the mill certificate.
- Weigh a bent part from its flat blank (use the bend allowance calculator), not its finished outside size.
Sources and further reading
- List of compulsory items to meet Pakistan Standards, Pakistan Standards and Quality Control Authority (PSQCA). Includes PS 4798 Structural Steel, PS-ISO 3573 Hot-Rolled Carbon Steel Sheet and PS-ISO 3574 Cold Reduced Carbon Steel Sheet of commercial and drawing qualities.
- PS 4798:2017 (Rev) Carbon Structural Steel, Pakistan Standards and Quality Control Authority (PSQCA). Based on ASTM A36/A36M-14; covers plates, shapes and bars. Table 2: tensile strength 400 to 550 MPa (58 to 80 ksi), minimum yield point 250 MPa (36 ksi).
- Standard wire gauge, Wikipedia. Table of Imperial Standard Wire Gauge sizes 1 to 30 in inches and mm.
Frequently asked questions
What is the weight of an 8 x 4 ft 20 gauge sheet?
About 21.4 kg in 20 SWG (0.914 mm). The US 20 gauge for steel is 0.912 mm, so at this gauge the two tables almost agree; at 22 gauge they differ by about 7%.
How do I calculate MS plate weight in kg?
Length (m) x width (m) x thickness (mm) x 7.85. A 1500 x 6000 mm plate 10 mm thick is 9 m² x 78.5 = 706.5 kg.
Which standard covers structural steel plate in Pakistan?
PS 4798, Carbon Structural Steel, revised in 2017 on the basis of ASTM A36/A36M-14. It covers plates, shapes and bars, and PSQCA lists structural steel among the compulsory items that must meet Pakistan Standards.
How much plate is in one tonne?
Divide 1,000 kg by the weight per square metre. For 10 mm plate at 78.5 kg/m² that is about 12.7 m²; for 6 mm plate at 47.1 kg/m², about 21.2 m².
Does the gauge table change the weight much?
It can. 22 SWG is 0.711 mm and US 22 gauge 0.759 mm, so an 8 x 4 ft sheet weighs 16.62 kg in one and 17.75 kg in the other. Ask for the thickness in mm when the price is per kg.
Is there an in-depth guide to the Sheet Metal Weight Calculator?
Yes. “How to Calculate Sheet Metal Weight (and Why Gauge Tables Disagree)” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.