Pakistan version. Opens on British SWG in millimetres with the US gauge tables beside it, and points to the PS-ISO sheet standards for ordering by thickness. US version

Sheet Metal Gauge to mm Converter (SWG and US Gauges)

Convert a sheet gauge to mm in British SWG or the US steel, GI, stainless and aluminium tables, or find the nearest gauge for a thickness in mm.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Sheet Metal Gauge Converter?

A gauge number is shorthand for a thickness, and the same number means a different thickness in each table. 22 SWG is 0.711 mm. In the US Manufacturers' Standard Gauge for plain steel, 22 gauge is 0.759 mm, and in the US galvanised table it is 0.853 mm. This version opens on the British Standard Wire Gauge (SWG) and shows the US tables next to it, so a gauge written on a quotation can be checked in millimetres before the order is placed.

The gap is not academic. At 7,850 kg/m³, 22 SWG steel weighs 5.58 kg per square metre and the US 22 gauge 5.96 kg, about 7% more steel for the same number. Where sheet is sold by weight, the table behind the number changes the bill.

For carbon steel sheet, PSQCA's list of items that must meet Pakistan Standards names PS-ISO 3573 for hot-rolled sheet and PS-ISO 3574 for cold-reduced sheet. Neither is a gauge table, so the safest purchase order gives the thickness in mm and the standard, and uses the gauge only as a cross-check.

  • Separate verified tables for steel, galvanized, stainless and aluminium, plus British SWG
  • Gauge to thickness and thickness to nearest gauge
  • Inches, millimetres and weight per area
  • Same gauge shown in every other table
  • Full side-by-side gauge chart with source notes
Read the guide: Sheet Metal Gauge Charts Explained: Steel, Galvanized, Stainless, Aluminium

Updated

How to use the Sheet Metal Gauge Converter

  1. Leave the table on British SWG, or pick the US steel, galvanised, stainless or aluminium table the supplier says it uses.
  2. For "Gauge to thickness", pick the gauge and read the thickness in mm and inches, with the same number in the other tables underneath.
  3. For "Thickness to gauge", type the thickness you measured with a micrometer in mm to see the nearest gauge and how far off it is.
  4. If no gauge in the table is within 0.1 mm, the converter says so: order that sheet by thickness only.

Worked examples

22 gauge in each table

Input

Gauge to thickness, 22

Output

SWG 0.711 mm (0.0280 in), 5.58 kg/m²; US steel 0.759 mm; US galvanised 0.853 mm; US stainless 0.795 mm; Brown & Sharpe (aluminium) 0.643 mm

Five tables give five thicknesses for one number. Between SWG and the US galvanised table the difference is 0.142 mm, a fifth of the sheet.

A 1.5 mm sheet

Input

Thickness to gauge, 1.5 mm

Output

SWG: 17 SWG (1.422 mm), 0.078 mm thinner. US steel: 16 gauge (1.519 mm), 0.019 mm thicker

The same sheet is "17 gauge" in one table and "16 gauge" in the other. That is why a gauge without its table is not enough on a drawing.

Thin sheet, 0.5 mm

Input

Thickness to gauge, 0.5 mm

Output

25 SWG (0.508 mm), 0.008 mm thicker; US steel 25 gauge is 0.531 mm

Both tables land on 25 here, but they still differ by 0.023 mm.

2 mm plate edge

Input

Thickness to gauge, 2 mm, SWG then US steel

Output

14 SWG (2.032 mm), 0.032 mm thicker; US steel 14 gauge is 1.897 mm, 0.103 mm thinner, and the converter warns that no US gauge is within 0.1 mm

At 2 mm and above, ordering by mm avoids the question entirely.

Background and insight

Gauges grew out of wire drawing, where the number counted the passes through successively smaller dies, which is why a higher number is thinner. For sheet steel the US settled on the Manufacturers’ Standard Gauge, which assigns thickness by weight at 41.82 lb per square foot per inch. Each steel thickness here is the nominal weight divided by that constant, so 10 gauge, nominally 5.625 lb/ft², is 0.1345 in. This is the table reproduced in Machinery’s Handbook.

Galvanized sheet uses its own gauge, which is the steel gauge plus a fixed allowance of about 0.0037 in for the zinc. Stainless is normally sold to the older US Standard Gauge of 1893, written into US law at 15 U.S.C. 206, which is why its values look like fractions of an inch (16 gauge is 1/16 in). Aluminium, copper and brass sheet use the Brown & Sharpe gauge, the same series as American Wire Gauge, defined by d = 0.005 x 92^((36 − n)/39) inches in ASTM B258.

Outside North America sheet is ordered in millimetres, and even in the US most mills and laser shops quote decimal thickness. Suppliers also round stainless and aluminium gauges differently, so treat any gauge as nominal and put the decimal thickness on the drawing and the purchase order.

Common use cases

  • Reading US drawings in metric

    Turn the gauge callouts on imported drawings into millimetres for a metric supplier.

  • Substituting metric sheet

    Find the closest metric thickness for a gauge and see how far off it is.

  • Checking quotes

    Make sure a quote for 14 gauge aluminium means 0.0641 in, not the 0.0747 in of 14 gauge steel.

  • Duct and HVAC work

    Look up galvanized gauges used in duct construction standards.

Tips and limitations

  • A higher gauge number is a thinner sheet in every table: 16 SWG is 1.626 mm, 20 SWG 0.914 mm, 24 SWG 0.559 mm.
  • Measure with a micrometer away from the sheet edge and the coating; on galvanised sheet, the US table includes the zinc in its thickness.
  • When a quotation says only "22 gauge", ask the supplier for the thickness in mm before comparing prices per sheet.

Sources and further reading

  1. List of compulsory items to meet Pakistan Standards, Pakistan Standards and Quality Control Authority (PSQCA). Includes PS 4798 Structural Steel, PS-ISO 3573 Hot-Rolled Carbon Steel Sheet and PS-ISO 3574 Cold Reduced Carbon Steel Sheet of commercial and drawing qualities.
  2. Standard wire gauge, Wikipedia. Table of Imperial Standard Wire Gauge sizes 1 to 30 in inches and mm.

Frequently asked questions

How thick is 22 gauge sheet in mm?

0.711 mm if it is SWG. The US steel table gives 0.759 mm, the US galvanised table 0.853 mm and the US stainless table 0.795 mm, so confirm which gauge the supplier means.

What is the difference between SWG and the US sheet gauge?

SWG is the British Imperial Standard Wire Gauge, with each number a set thickness in thousandths of an inch. US sheet steel uses the Manufacturers' Standard Gauge, based on weight per square foot, and US stainless and aluminium have their own tables. The numbers overlap but the thicknesses do not.

Which Pakistan Standards cover carbon steel sheet?

PSQCA's list of compulsory items includes PS-ISO 3573 for hot-rolled carbon steel sheet and PS-ISO 3574 for cold-reduced carbon steel sheet, both of commercial and drawing qualities. Structural plate, shapes and bars come under PS 4798.

Why is my 1.5 mm sheet 17 gauge in one chart and 16 in another?

Because 17 SWG is 1.422 mm and US 16 gauge steel is 1.519 mm, and 1.5 mm happens to sit nearest to each in its own table. The sheet is the same; only the label changes.

How do I convert a gauge to kg per square metre?

Thickness in mm x 7.85 gives kg/m² for steel. 22 SWG at 0.711 mm is 5.58 kg/m²; use the sheet weight calculator for whole sheets.

Is there an in-depth guide to the Sheet Metal Gauge Converter?

Yes. “Sheet Metal Gauge Charts Explained: Steel, Galvanized, Stainless, Aluminium” covers the background, how it works, common pitfalls and worked examples. Read the full guide.