Australia version. Metric runs with 2.35 m Colorbond steel panels or timber paling fences, 20 kg concrete bags, A$ prices and how dividing fence costs are shared between neighbours. US version

Fence Calculator (Australia)

Count Colorbond panels or timber palings, rails, posts and 20 kg concrete bags for a boundary fence in metres, with gates, corners and dividing fence cost sharing.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Fence Calculator?

Most Australian boundary fences are either Colorbond steel or timber paling. A Lysaght Neetascreen panel is 2350 mm wide, so a 30 metre side boundary takes 13 panels and 14 posts; the calculator spreads the run evenly, so each bay comes out at 2.31 metres and one or more panels are trimmed on site.

For a paling fence the tool counts rails and palings. A 20 metre fence with posts at 2.4 metres needs 9 bays and 10 posts, three rails per bay for a 1.8 metre fence, and 142 palings of 150 mm butted together, including 5% for splits and offcuts.

Between neighbours the cost of a dividing fence is usually shared. In New South Wales the Dividing Fences Act 1991 has adjoining owners share the cost of a sufficient dividing fence equally, and anyone who wants something better than that pays the difference. Other states have their own Acts, so check yours before ordering.

  • Any number of straight runs with gates, open or closed layouts
  • Rails and pickets or prefabricated panels
  • Concrete per post and in total, in 40, 50, 60 and 80 lb or 20 and 25 kg bags
  • Run-by-run table with the real section length for layout
  • Material cost and post length; runs in the browser with a share link
Read the guide: How to Estimate Fence Posts, Pickets, Rails and Concrete

Updated

How to use the Fence Calculator

  1. Measure each straight side in metres and enter one run per side, with any gates.
  2. For Colorbond, choose panels and set the post centres to the panel width in your kit, such as 2.35 m.
  3. For a paling fence, choose rails and boards, enter 3 rails for a 1.8 m fence, the paling width in mm and a gap of 0 for butted palings.
  4. Enter the post size, hole diameter and depth from the installation guide for your kit or timber posts.
  5. Pick 20 kg bags and enter A$ prices for posts, panels or palings and concrete.

Worked examples

Colorbond side boundary, 30 m

Input

One 30 m run, 2.35 m panels, 1.8 m high, 50 mm posts in 300 mm holes 600 mm deep, 20 kg bags

Output

13 panels, 14 posts of 2.4 m, about 41 litres a post; 62 bags of 20 kg in all (5 a post if you mix each hole separately)

The bags are counted on the total concrete, so they come to fewer than 5 for every post. Check the hole size in the Lysaght installation guide for your wind region; it may call for less.

Back and sides of a suburban block

Input

Runs of 15 m, 20 m and 15 m, open at the house, 2.35 m Colorbond panels

Output

23 panels and 24 posts

The two 15 m sides take 7 panels each and the 20 m back 9. Each neighbour usually shares the cost of their side, so price the runs separately to split the bill.

Timber paling fence, 20 m

Input

20 m run, posts at 2.4 m, 1.8 m high, 3 rails, 150 mm palings butted, 5% extra, 100 mm posts in 300 mm holes 600 mm deep

Output

10 posts, 29 rails, 142 palings, 39 bags of 20 kg

With 100 mm palings the same fence needs 218 palings. Lapped and capped fences overlap palings, so enter the cover width of each paling instead of its full width.

Background and insight

Post spacing is a maximum, not a rule that every section must hit. Wood privacy fences are commonly built with posts 6 to 8 feet on centre, because 8 foot rails are a stock length and longer spans sag. When a run does not divide evenly, the calculator rounds the number of sections up and spreads the length evenly, so a 50 foot run at 8 foot maximum spacing becomes 7 sections of 7.14 feet instead of six full sections and a stub.

Gates are assumed to be spaced evenly within their run. That gives the fewest posts; a gate placed off-centre can need one more section on one side, so check the run table against your plan. Each gate needs its own pair of posts, which should be set deeper or larger because a swinging gate loads the hinge post sideways.

Concrete is the hole volume minus the part of the hole the post fills. A common rule from post and concrete manufacturers is a hole about three times the post width and at least a third to a half as deep as the post stands above ground, and always below the local frost line so frost heave cannot lift the post. Bag yields come from published data: an 80 lb bag of concrete mix makes about 0.60 cubic feet and a 50 lb bag of fast-setting mix about 0.375 cubic feet.

Common use cases

  • Privacy and picket fences

    Get the post, rail and picket list for a wood fence before ordering lumber.

  • Panel fences

    Count vinyl or wood panels and the posts between them for a yard with several sides.

  • Gates and corners

    See how gates and changes of direction change the post count instead of guessing.

  • Concrete order

    Buy the right number of bags for every post hole in one trip.

Tips and limitations

  • Give your neighbour a fencing notice before you start work on a dividing fence; most state Acts set out how.
  • Pool barriers are a separate matter. They must meet the state pool safety laws and Australian Standard AS 1926.1, which this tool does not check.
  • Dial Before You Dig (now Before You Dig Australia) before setting posts near services.
  • Colorbond panels come in set heights; a sloping block is stepped panel by panel, which can add posts.

Sources and further reading

  1. Fences, boundaries and retaining walls: FAQs, Legal Aid NSW. How the Dividing Fences Act 1991 shares the cost of a sufficient dividing fence.
  2. Dividing Fences Act 1991 No 72, NSW Legislation
  3. NEETASCREEN fencing, Lysaght. Panel widths of 2350 mm (2370 mm in SA) and heights of 1500, 1800 and 2100 mm.

Frequently asked questions

How many Colorbond panels do I need?

Divide each run by the panel width and round up. With 2.35 m panels a 30 m side fence needs 13 panels and 14 posts. Some kits use other widths, such as 3.1 m, so enter the width on your quote.

Do I have to share the cost of a fence with my neighbour?

Usually yes. In NSW, adjoining owners share the cost of a sufficient dividing fence equally under the Dividing Fences Act 1991, and an owner who wants a higher standard pays the extra. Victoria, Queensland and the other states have their own fencing laws with similar notices and sharing rules.

How many palings do I need per metre?

Divide 1,000 mm by the paling width plus any gap. With 150 mm palings butted together that is 6.7 per metre, so about 7; with 100 mm palings it is 10 per metre. Add a few percent for split palings.

How deep should fence posts be in Australia?

Follow the installation guide for your fence system and wind region. For timber posts a common practice is about a quarter of the post length in the ground, such as 600 mm for a 1.8 m fence on a 2.4 m post.

How many bags of concrete per fence post?

The calculator works it out from the hole and post size. A 300 mm hole 600 mm deep around a 100 mm timber post takes about 36 litres, four 20 kg bags of general-purpose concrete.

What does a boundary fence cost?

Prices depend on the material, height, site access and region, so enter your own quotes per panel, post and bag. The tool totals materials only, not labour or removal of the old fence.

Is there an in-depth guide to the Fence Calculator?

Yes. “How to Estimate Fence Posts, Pickets, Rails and Concrete” covers the background, how it works, common pitfalls and worked examples. Read the full guide.