Canada version. Shows cc, litres and cubic inches side by side and checks bikes against the 125 cc and 400 cc limits of Quebec's Class 6C and 6B motorcycle licences. US version

Engine Displacement Calculator (Canada)

Displacement from bore and stroke in mm or inches, in cc, litres and cubic inches, with Quebec's 125 cc and 400 cc motorcycle licence classes and rebore effects.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Engine Displacement Calculator?

Canadian engines are described three ways at once: motorcycles in cc, new cars and trucks in litres, and older North American V8s by their cubic inches. This version starts in millimetres and cc for a motorcycle twin, and every result also shows litres and cubic inches.

In Quebec, engine size also decides which motorcycle licence you need. The SAAQ issues Class 6A for any motorcycle, Class 6B for motorcycles with an engine displacement of 400 cc or less, and Class 6C for 125 cc or less. A rebore can move a bike out of the class its rider holds, so the overbore field is worth a look before a big-bore kit goes on.

  • Displacement in cc, litres and cubic inches at once, with per-cylinder volume
  • Solve for bore or stroke from a target displacement in any of the three units
  • Overbore gain, bore/stroke ratio with oversquare or undersquare label, and mean piston speed
  • Inch and millimetre inputs that convert in place, plus a table for other cylinder counts
  • Copy results and share a link with your inputs
Read the guide: Engine Displacement Explained: Bore, Stroke, CC and Cubic Inches

Updated

How to use the Engine Displacement Calculator

  1. Choose inches or millimetres for bore and stroke.
  2. Leave "Solve for" on Displacement and enter bore, stroke and the number of cylinders.
  3. Read total displacement in cc, litres and cubic inches, plus the per-cylinder volume and bore/stroke ratio.
  4. To plan a rebore, enter the oversize (for example 0.030 in) and read the new displacement and the gain.
  5. To hit a target size, switch "Solve for" to Bore or Stroke, enter the target in cc, litres or cubic inches, and read the required dimension.

Worked examples

A 400-class twin after a rebore

Input

66 mm bore, 58 mm stroke, 2 cylinders, 0.5 mm overbore

Output

396.86 cc standard; 402.89 cc after the rebore

At standard bore this twin is within the 400 cc limit of a Class 6B licence. A half-millimetre oversize takes it 2.9 cc over.

A 125 for a Class 6C rider

Input

54 mm bore, 54.5 mm stroke, 1 cylinder

Output

124.82 cc, 7.62 cu in

Under the 125 cc limit by less than 0.2 cc, so even the smallest oversize piston pushes it over.

Truck engine in litres and cubic inches

Input

96 mm bore, 92 mm stroke, 8 cylinders

Output

5,327.34 cc, 5.327 L, 325.09 cu in

A "5.3 litre" V8 is a 325 in North American cubic inches. Switch the units to inches if your parts catalogue lists bore and stroke that way.

Background and insight

One cylinder sweeps a cylinder of air with the bore as its diameter and the stroke as its height: V = π/4 x bore² x stroke. Multiply by the cylinder count for the engine total. Because bore is squared, it moves displacement faster than stroke does: a 1% larger bore adds about 2% volume, a 1% longer stroke adds 1%. One cubic inch is exactly 16.387064 cc, since the inch is defined as 25.4 mm.

Advertised sizes are rounded. A Honda K20 is 86 x 86 mm, which works out to 1,998.2 cc and is sold as a 2.0 litre; Ford's 302 measures 301.6 cu in. Rotary and two-stroke engines are counted differently for racing and tax purposes, so check the rulebook if a class limit is at stake.

The bore/stroke ratio says something about character. Oversquare engines (ratio above 1) have room for larger valves and lower piston speed at a given rpm, so they tend to rev; undersquare engines trade that for a compact chamber and strong low-speed torque. Mean piston speed, 2 x stroke x rpm, is a rough check on how hard the rotating parts work: around 20 m/s is common for road engines at their redline, and racing engines run higher with lighter parts.

Common use cases

  • Engine builds and strokers

    Plan the bore and stroke combination that reaches a target size, and see what a rebore adds before the block goes to the machine shop.

  • Class and registration limits

    Check a motorcycle, kart or race engine against a displacement limit after an overbore.

  • Spec sheet checks

    Confirm a quoted engine size from published bore and stroke, and convert between cc, litres and cubic inches.

  • Teaching engine basics

    Show how bore, stroke and cylinder count combine, and why bore has twice the effect of stroke on volume.

Tips and limitations

  • Canadian machine shops quote oversizes in both thou and millimetres. Set the length units to match the piston box before entering the oversize.
  • The SAAQ classes apply in Quebec. Other provinces license motorcycles differently, so check your provincial licensing authority.
  • An engine with a different displacement may need to be declared to your insurer and provincial registry.
  • Use the cubic-inch result to compare a metric bore and stroke with American engine names such as 302, 350 or 454.

Sources and further reading

  1. Obtaining a Motorcycle Driver's Licence (Classes 6A, 6B and 6C), Société de l'assurance automobile du Québec. Class 6B up to 400 cc, Class 6C up to 125 cc
  2. SI Units: Length, National Institute of Standards and Technology. The inch is exactly 25.4 mm, so 16.387064 cc per cubic inch

Frequently asked questions

Which motorcycle licence class do I need in Quebec?

The SAAQ lists Class 6A for any motorcycle, Class 6B for motorcycles of 400 cc or less and Class 6C for 125 cc or less. The calculator shows the displacement from bore and stroke; the class is set by the motorcycle's rated displacement.

How many cubic inches is a 5.3 litre engine?

About 325 cubic inches: 5,327 cc divided by 16.387 cc per cubic inch. The calculator shows all three units for any bore and stroke.

Does a rebore change which licence I need?

It changes the engine's displacement. On the 396.86 cc twin, a 0.5 mm oversize takes it to 402.89 cc, above the 400 cc Class 6B limit. Check with the SAAQ and your insurer before modifying a bike near a limit.

How do I calculate displacement in cc?

Displacement = 0.7854 x bore² x stroke x cylinders, with bore and stroke in centimetres. For 66 mm x 58 mm and two cylinders: 0.7854 x 6.6² x 5.8 x 2 = 397 cc.

Should I measure in millimetres or inches?

Use whatever your manual or parts supplier uses. Motorcycle and import engines are specified in millimetres; many North American V8 parts are listed in inches. The calculator converts the inputs when you switch.

Is there an in-depth guide to the Engine Displacement Calculator?

Yes. “Engine Displacement Explained: Bore, Stroke, CC and Cubic Inches” covers the background, how it works, common pitfalls and worked examples. Read the full guide.