United Kingdom version. Metric, priced per tonne in pounds, with 20 kg and 25 kg bags, 850 kg and 1 tonne bulk bags, and bark mulch in litre bags as UK merchants sell them. US version

Gravel and Bark Calculator (UK)

How much gravel, MOT Type 1 or bark you need in m³ and tonnes, with 25 kg bags, 850 kg bulk bags or 1 tonne bags, and bark in 70 litre bags, priced in pounds.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Gravel and Mulch Calculator?

UK builders merchants sell gravel and sub-base by weight: 20 kg or 25 kg bags for small jobs, and bulk bags delivered by crane lorry, commonly listed at about 850 kg or a full tonne. Bark and soil come in litre bags. This version turns your area and depth into cubic metres, then tonnes, then whole bags of the size you are buying.

A 10 by 3 m gravel driveway topped 50 mm deep, with 5% for settling, is 1.58 m³. At the default density of 1,661 kg/m³ that is 2.62 tonnes, so four 850 kg bulk bags or 105 small 25 kg bags. Bulk bags are almost always the sensible choice above a tonne.

  • Gravel, crushed stone, sand, topsoil, mulch or a custom density
  • Cubic yards, cubic metres, short tons, tonnes and bags at once
  • Rectangle, circle, triangle or known-area input with depth in inches or centimetres
  • Bagged versus bulk cost comparison
  • Density reference table; copy and share results
Read the guide: Estimating Concrete, Flooring, Tile and Gravel Without Running Short

Updated

How to use the Gravel and Mulch Calculator

  1. Measure the area in metres and choose the depth in centimetres.
  2. Pick the material; the density fills in, but ask your merchant for theirs because bulk bag weights vary.
  3. Choose the bag your merchant sells: 25 kg, 850 kg or 1 tonne for stone, 70 litres for bark.
  4. Set the bulk price per tonne to compare a delivered load with small bags.

Worked examples

Gravel driveway topping

Input

10 x 3 m, 5 cm deep, gravel at 1,661 kg/m³, 5% extra, 850 kg bulk bags

Output

1.58 m³; 2.62 tonnes; 4 bulk bags (or 105 bags of 25 kg)

The decorative top layer sits on a compacted sub-base. Check whether your merchant's bulk bag holds about 850 kg or a full tonne before ordering.

MOT Type 1 sub-base for the same drive

Input

30 m², 10 cm deep, crushed stone at 1,602 kg/m³, 5% extra, 1 tonne bags

Output

3.15 m³; 5.05 tonnes; 6 one-tonne bags

Sub-base is compacted with a plate compactor and settles, so many people order more than the loose volume; the compaction allowance depends on the material.

Bark mulch for borders

Input

12 m² of beds, 7.5 cm deep, wood mulch, 5% extra, 70 litre bags

Output

0.94 m³; 14 bags of 70 litres

The RHS suggests a mulch at least 5 cm thick and ideally 7.5 cm. At 5 cm the same beds need about 9 bags.

Background and insight

Volume is area times depth, with depth converted from inches to feet (divide by 12) or centimetres to metres. A 10 x 10 ft bed covered 3 inches deep holds 25 cubic feet, which is 0.93 cubic yards. Weight then depends on density, and loose aggregate varies more than most people expect: dry gravel and crushed stone are around 2,700 to 2,800 lb per cubic yard (1.35 to 1.4 short tons), topsoil around 2,200 lb, and wood mulch only a few hundred pounds. Wet sand and soil can be 10 to 20% heavier.

The densities in this tool are typical published values for loose, dry material and are labelled as approximate. Quarries weigh each load on a scale, so a ton of their product may be a little more or less volume than the estimate. When you buy by the ton, ask the yard for their conversion factor and enter it.

Common use cases

  • Paths and patios

    Size the base and top layer for a gravel path or a paver patio bed of sand.

  • Garden beds

    Order mulch or topsoil for new and existing beds without a second trip to the garden centre.

  • Driveways and parking pads

    Convert a driveway plan to tons of crushed stone for a quarry delivery.

  • Comparing bags and bulk

    See how many bags a job takes and whether a bulk delivery is cheaper once the fee is included.

Tips and limitations

  • Put a weed membrane under decorative gravel paths, and an edging to stop stone spreading into lawns.
  • Bulk bags need a firm, accessible drop point; crane lorries cannot always reach the back of a terraced house.
  • Loose gravel is permeable, so in England it does not need the planning permission that more than 5 m² of impermeable front-garden paving draining to the road does.
  • Twenty-five kilogram bags add up fast: 105 of them is a lot of lifting, so HSE manual handling advice to reduce loads applies at home too.

Sources and further reading

  1. Permeable surfacing of front gardens: guidance, Ministry of Housing, Communities and Local Government. The 5 m² rule for impermeable front-garden surfaces in England.
  2. Mulch, Royal Horticultural Society. Mulch at least 5 cm and ideally 7.5 cm thick.
  3. Manual handling at work, Health and Safety Executive

Frequently asked questions

How many bulk bags of gravel do I need for a driveway?

Multiply area by depth to get m³, multiply by about 1.6 to 1.7 tonnes per m³, then divide by the bag weight. A 30 m² drive topped 50 mm deep needs about 2.6 tonnes, so four 850 kg bulk bags.

How much does a bulk bag of gravel cover?

An 850 kg bag at about 1,661 kg/m³ is roughly 0.51 m³. At 50 mm deep that covers about 10 m²; at 30 mm it covers about 17 m².

How many tonnes of MOT Type 1 do I need?

Multiply the area by the compacted depth and by about 1.6 tonnes per m³. A 30 m² drive with a 10 cm sub-base and 5% extra is 3.15 m³, about 5.05 tonnes, so six 1 tonne bags. Ask your merchant for the density of their stone.

How many 70 litre bags of bark do I need?

Multiply the bed area in m² by the depth in metres to get m³, multiply by 1,000 for litres and divide by 70. Twelve square metres at 7.5 cm is 900 litres, or about 14 bags with a little extra.

What depth of gravel should a path be?

Decorative gravel paths are usually laid thin over a firm base so the stones do not roll underfoot. Use the depth your supplier recommends for the stone size you choose, and put the depth into the tool.

Is there an in-depth guide to the Gravel and Mulch Calculator?

Yes. “Estimating Concrete, Flooring, Tile and Gravel Without Running Short” covers the background, how it works, common pitfalls and worked examples. Read the full guide.