Data Transfer Rate Converter

Convert data transfer rates between bit/s, kbit/s, Mbit/s, Gbit/s, B/s, KB/s, MB/s and MiB/s. See why a 100 Mbps plan downloads at 12.5 MB/s.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Data Transfer Rate Converter?

Type a transfer rate once and read it in every common unit at the same time: bits per second, kilobits, megabits and gigabits per second, and bytes, kilobytes, megabytes and mebibytes per second. The usual surprise is the factor of 8. Internet plans are sold in megabits per second while download dialogs report megabytes per second, so a 100 Mbit/s connection tops out at 12.5 MB/s and that is the plan working exactly as advertised.

The byte-per-second units here follow the SI decimal prefixes that operating systems and ISPs use for rates, so 1 MB/s is exactly 1,000,000 bytes per second. The one binary unit, the mebibyte per second (MiB/s), is included because some torrent clients, file managers and server dashboards report in it: 1 MiB/s is 1,048,576 bytes per second, about 4.9 percent more than 1 MB/s.

Everything runs in your browser and no value is sent anywhere. Pick a target unit and the working steps spell out the exact definition applied, such as 1 byte = 8 bits and 1 Mbit/s = 1,000,000 bit/s, then export the full conversion table as CSV or PDF from the report bar or copy a link that reopens the page with your numbers filled in.

  • One rate converted to all eight bit and byte units in a single table
  • Working steps for any target unit, showing 1 byte = 8 bits and each prefix factor
  • Decimal (MB/s) and binary (MiB/s) byte rates side by side
  • CSV and PDF export of the full conversion table from the report bar
  • Runs entirely in the browser with a shareable link to your exact conversion
Read the guide: Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets

Updated

How to use the Data Transfer Rate Converter

  1. Enter the rate your plan, dashboard or speed test reports.
  2. Pick the unit it is in, for example Mbit/s for an ISP plan or MB/s for a download dialog.
  3. Read the result in all eight units at once in the table.
  4. Select a target unit to see the working steps with the exact factors used.
  5. Export the table as CSV or PDF, or copy the share link, from the report bar.

Worked examples

ISP plan to download speed

Input

100 Mbit/s

Output

12.5 MB/s

100 Mbit/s is 100,000,000 bits per second. Dividing by 8 bits per byte gives 12,500,000 bytes per second, which is 12.5 MB/s. The plan is delivering full speed even though the number looks eight times smaller.

Gigabit fiber in binary units

Input

1 Gbit/s

Output

125 MB/s, or about 119.21 MiB/s

1 Gbit/s is 125,000,000 B/s. A mebibyte is 1,048,576 bytes, so the same rate is 125,000,000 / 1,048,576 = 119.209 MiB/s, which is why a torrent client shows a smaller number than the file manager.

Real-world gigabit speed test

Input

940 Mbit/s

Output

117.5 MB/s

A wired speed test on gigabit fiber typically reads about 940 Mbit/s because TCP and Ethernet overhead consume the rest of the line rate. 940,000,000 / 8 = 117,500,000 B/s.

Old modem rate

Input

56 kbit/s

Output

7 KB/s

56,000 bits per second divided by 8 is 7,000 bytes per second. A 5 MB file at that rate needed about 12 minutes, which is why image-heavy pages were kept small in the dial-up era.

Background and insight

The factor of 8 is a historical settlement. Early machines used word and byte sizes from 6 to 36 bits, and network engineers still say octet when they need to be unambiguous, which is why French ISPs advertise in Mo/s (megaoctets). The 8-bit byte won through the IBM System/360 in 1964 and was later fixed in ISO/IEC 80000-13, the standard this converter follows.

Marketing in bits per second is not a trick. Serial links genuinely move one bit at a time, so line rate in bit/s is the honest physical measure, and it has been quoted that way since modem days: a 56k modem meant 56 kbit/s, which is 7 KB/s. The confusion only arrives at the file level, where sizes are counted in bytes.

Real throughput lands below the converted figure because every layer adds framing. On a gigabit Ethernet link carrying TCP over IPv4, headers, the inter-packet gap and preamble leave roughly 94 percent for payload, so the practical ceiling is about 118 MB/s rather than the raw 125 MB/s this page reports for 1 Gbit/s. The conversion gives you the line rate; protocol overhead is subtracted from there.

Common use cases

  • Checking an ISP plan

    Confirm that the MB/s figure in your download manager matches the Mbit/s plan you pay for before opening a support ticket.

  • Estimating transfer time

    Convert a backup target or NAS sync rate into MB/s to work out how long a 500 GB copy will take.

  • Sizing video streams

    Compare a 25 Mbit/s 4K stream against your uplink or a hotel network quoted in kbit/s.

  • Reading server dashboards

    Reconcile a monitoring graph in MiB/s with a network interface counter in bit/s during an incident.

Tips and limitations

  • Lowercase b means bits and uppercase B means bytes: 10 Mb/s and 10 MB/s differ by a factor of 8.
  • Speed tests report line throughput after protocol overhead, so expect roughly 94 percent of the nominal rate on a healthy wired gigabit link.
  • MiB/s is 4.9 percent larger than MB/s; the gap grows to 7.4 percent at the gibibyte level, so name the unit when you file a bug about transfer speed.
  • Transfer time in seconds is file size in bytes divided by rate in B/s; convert the rate here first, then divide.
  • Wi-Fi link rates (for example 866 Mbit/s on 802.11ac) are physical-layer figures; real throughput is often half that before you convert anything.

Sources and further reading

  1. NIST Special Publication 811: Guide for the Use of the International System of Units, NIST. Prefix definitions, including the binary prefixes kibi and mebi
  2. Data-rate units, Wikipedia. Survey of bit and byte rate units and where each is used
  3. Byte, Wikipedia. History of the 8-bit byte and the octet

Frequently asked questions

Why is 100 megabits per second only 12.5 megabytes per second?

A byte is 8 bits, so any rate in bits per second divides by 8 to give bytes per second. 100 Mbit/s = 100,000,000 bit/s = 12,500,000 B/s = 12.5 MB/s. ISPs quote bits because that is what the line physically carries; file sizes are counted in bytes.

Is Mbps the same as MB/s?

No. Mbps (megabits per second) is 8 times smaller than MB/s (megabytes per second). A 400 Mbps plan delivers at most 50 MB/s. The lowercase b versus uppercase B is the whole difference.

What is the difference between MB/s and MiB/s?

MB/s uses the decimal megabyte of 1,000,000 bytes; MiB/s uses the binary mebibyte of 1,048,576 bytes, as defined in ISO/IEC 80000-13. The same transfer reads about 4.9 percent lower in MiB/s, which is why torrent clients and file managers disagree.

How many MB/s is gigabit internet?

A 1 Gbit/s line is 125 MB/s of raw capacity. After Ethernet and TCP/IP overhead, a wired speed test usually shows about 940 Mbit/s, which is 117.5 MB/s of usable payload.

How do I calculate download time from my connection speed?

Convert the connection speed to bytes per second, then divide the file size in bytes by it. A 10 GB game on a 300 Mbit/s plan: 300 Mbit/s = 37.5 MB/s, and 10,000 MB / 37.5 MB/s = 267 seconds, about 4.5 minutes.

Why does my speed test show less than my plan?

Protocol overhead, Wi-Fi losses and server limits all shave the number. On a wired gigabit connection, about 6 percent goes to Ethernet framing and TCP/IP headers alone. If the shortfall is much larger than that, test over a cable before blaming the ISP.

What does kbps mean on a hotel or mobile network?

Kilobits per second: 1,000 bits per second each. A 512 kbps connection moves 64 KB/s, enough for audio streaming at 128 kbit/s with room to spare but slow for video, since even 480p typically wants 1 to 2.5 Mbit/s.

Is there an in-depth guide to the Data Transfer Rate Converter?

Yes. “Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets” covers the background, how it works, common pitfalls and worked examples. Read the full guide.