Frequency Converter
Convert frequency between hertz, kilohertz, megahertz, gigahertz, rpm, bpm and radians per second. 3,000 rpm is 50 Hz, shown step by step.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Frequency Converter?
One frequency, every unit at once: hertz, kilohertz, megahertz and gigahertz alongside revolutions per minute, beats per minute and radians per second. The same physical idea, events per unit time, hides behind very different numbers: concert pitch A4 is 440 Hz, an idling engine turns at about 800 rpm, mains power alternates at 50 or 60 Hz, FM radio sits near 100 MHz and a desktop CPU clocks past 3 GHz.
The hertz, one cycle per second, is the SI derived unit, and the per-minute units divide by 60 to reach it: 3,000 rpm is exactly 50 Hz, and a 120 bpm track pulses at 2 Hz. Radians per second is angular frequency, ω = 2πf, used whenever rotation or oscillation enters an equation, so 50 Hz corresponds to 314.159 rad/s.
Nothing you type leaves the browser. Selecting a target unit opens the working steps with the definition applied, whether that is dividing rpm by 60 or multiplying hertz by 2π, and the report bar exports the complete table as CSV or PDF or copies a link that brings the conversion back exactly as you set it.
- Hertz through gigahertz plus rpm, bpm and rad/s in one combined table
- Working steps for the target unit you choose, including the 2π factor for angular frequency
- Exact per-minute conversions using 1 rpm = 1/60 Hz
- CSV and PDF export of every converted value via the report bar
- Browser-only calculation with a link that reopens your exact conversion
Updated
How to use the Frequency Converter
- Enter the frequency from your datasheet, tachometer, tuner or spec sheet.
- Choose the unit it came in, from hertz up to gigahertz, or rpm, bpm or rad/s.
- Read the equivalent in all seven units from the table.
- Pick a target unit to see the steps, such as rpm ÷ 60 = Hz or Hz × 2π = rad/s.
- Export the table as CSV or PDF, or share the preset link, from the report bar.
Worked examples
Engine speed to hertz
Input
3,000 rpm
Output
50 Hz
3,000 revolutions per minute ÷ 60 seconds per minute = 50 revolutions per second. A four-cylinder four-stroke engine at this speed fires 100 times a second, which is the drone you hear.
Redline in angular frequency
Input
6,500 rpm
Output
108.33 Hz = 680.68 rad/s
6,500 / 60 = 108.333 Hz, and multiplying by 2π gives 680.678 rad/s. Angular frequency is what enters the centripetal stress formula for the crankshaft, not rpm.
Concert pitch as a rotation
Input
440 Hz
Output
26,400 rpm
A4 vibrates 440 times a second, which is 440 × 60 = 26,400 cycles per minute, faster than most turbochargers idle. The same ÷60 and ×60 bridge links audio and machinery units.
Music tempo to hertz
Input
120 bpm
Output
2 Hz
120 beats per minute ÷ 60 = 2 beats per second. Delay effects synced to tempo use this directly: an eighth-note delay at 120 bpm is 250 ms, the period of 4 Hz.
Background and insight
The unit honors Heinrich Hertz, who demonstrated radio waves in 1887; the name replaced "cycles per second" by international agreement in 1960, though old test gear and American electricians still say cycles. The SI Brochure defines the hertz strictly for periodic phenomena, which is why becquerels, not hertz, count radioactive decays even though both are formally 1/s.
Rotating machinery kept the minute. Engine tachometers, hard drives (7,200 rpm), lathes and fans are all specified in revolutions per minute, a habit from the era of counting flywheel turns against a pocket watch. The conversion matters in practice: a 2-pole induction motor on 60 Hz mains can never quite reach the synchronous 3,600 rpm, and the few-percent shortfall, the slip, is a direct diagnostic of load.
Angular frequency ω = 2πf exists because calculus prefers radians. The voltage of 50 Hz mains is v(t) = V sin(314.159 t), not sin(50 t), and mixing f and ω is a standing hazard in filter design: a cutoff computed as 1/(RC) is in rad/s, and quoting it as hertz overstates the cutoff by a factor of 6.28.
Common use cases
Motor and pump checks
Compare a nameplate rpm with the mains frequency to verify pole count and spot slip under load.
Audio and music production
Relate tempo in bpm to LFO rates and delay times in hertz when syncing effects.
Electronics design
Move between hertz and radians per second when reading filter formulas or oscilloscope measurements.
Spec sheet reading
Put CPU gigahertz, Wi-Fi channel megahertz and drive rpm on one scale when comparing hardware.
Tips and limitations
- rpm and bpm are numerically identical conversions (both ÷60 to Hz); only the counted event differs, revolutions versus beats.
- Filter formulas like 1/(2πRC) already include the 2π and give hertz; 1/(RC) gives rad/s. Check which form your reference uses before converting.
- Synchronous motor speed is 120 × mains frequency ÷ poles, so 60 Hz with 4 poles gives 1,800 rpm; a reading of 1,750 rpm is normal slip.
- Period is the reciprocal of frequency: 50 Hz has a 20 ms period, which is the figure you line up against on an oscilloscope.
- Audible sound spans roughly 20 Hz to 20 kHz; anything in megahertz on an audio datasheet is a sampling or clock figure, not a pitch.
Sources and further reading
- SI Brochure: The International System of Units (SI), BIPM. Defines the hertz and distinguishes it from the becquerel
- Hertz, Wikipedia. Adoption of the hertz over cycles per second
- Angular frequency, Wikipedia. The ω = 2πf relationship
Frequently asked questions
How do you convert rpm to Hz?
Divide by 60, because a minute holds 60 seconds. 3,000 rpm = 50 Hz and 7,200 rpm (a classic hard drive speed) = 120 Hz. Going the other way, multiply hertz by 60.
What is the relationship between Hz and rad/s?
Angular frequency ω equals 2πf. One cycle sweeps 2π radians, so 50 Hz is 314.159 rad/s and 1 rad/s is 0.15915 Hz. Physics and filter equations use ω; instruments and datasheets quote f.
Why do motors on 60 Hz mains run at 1,800 or 3,600 rpm?
Synchronous speed is 120 × frequency ÷ number of poles. On 60 Hz, a 2-pole motor targets 3,600 rpm and a 4-pole motor 1,800 rpm; induction motors run a few percent slower under load. On 50 Hz mains, the same motors target 3,000 and 1,500 rpm.
How do I convert bpm to Hz for delay and LFO settings?
Divide bpm by 60 to get beats per second. At 128 bpm the beat is 2.1333 Hz with a 468.75 ms period; a quarter-note delay uses that period, an eighth note half of it.
Is a GHz a billion hertz?
Yes, 1 GHz = 1,000,000,000 Hz. A 3.5 GHz CPU completes 3.5 billion clock cycles per second, each lasting about 0.286 nanoseconds, during which light travels only about 8.6 cm.
Why is radioactive decay measured in becquerels and not hertz?
Both are 1 per second, but the SI reserves hertz for periodic, repeating events. Decays are random, so the becquerel counts them instead; this converter covers periodic frequency only.
Is there an in-depth guide to the Frequency Converter?
Yes. “Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.