Canada version. Uses Canadian metric bar sizes 10M to 35M from CSA G30.18 (0.785 kg/m for 10M, 1.570 for 15M), metric lengths and covers, and CA$ for the price per bar. US version

Rebar Calculator (Canadian 10M to 35M Bars)

Count 10M, 15M or 20M bars for a slab, footing or mat with CSA G30.18 masses in kg per metre, laps in bar diameters and the number of stock bars to order.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Rebar Calculator?

Canadian rebar is metric and named by size rather than diameter: 10M is an 11.3 mm bar with a nominal area of 100 mm², 15M is 16 mm and 200 mm², 20M is 19.5 mm and 300 mm². The masses follow from those areas at 7,850 kg/m³: 0.785, 1.570 and 2.355 kg/m. This version uses the CSA G30.18 sizes from 10M to 35M; the US #3 to #11 sizes stay in the list for imported drawings.

Enter the slab or footing size, the cover and the spacing each way. The tool counts the bars, adds laps where a run is longer than the stock bar, nests the offcuts, and gives the length, the kilograms and the stock bars to buy. Bars are ordered from a supplier by weight or by piece, and laps and covers come from the drawings, which follow CSA A23.3 for design and CSA A23.1 for construction.

  • US bar sizes #3 to #11 with ASTM A615 weights and metric 8 to 32 mm bars
  • Single or double mats, edge cover, hooks and lap splices
  • Stock-length cutting estimate with offcut and lap count
  • Steel area per foot or per metre of width for design checks
  • Copy, share link and cost per stock bar; runs in your browser
Read the guide: Rebar Takeoff for Slabs: Bar Counts, Laps, Cutting and Weight

Updated

How to use the Rebar Calculator

  1. Pick imperial or metric. Plan dimensions are in feet or metres; cover, spacing and laps are in inches or millimetres.
  2. Enter the slab or footing length and width and the edge cover. Add a hook or bend length per end if the bars turn up at the edges.
  3. Choose the bar size and the centre-to-centre spacing of the bars running along the length and along the width.
  4. Select a single mat or top and bottom mats, the stock length your supplier sells, and the lap length in bar diameters or as a length.
  5. Read the bar counts, total length, weight and stock bars to buy, then copy the takeoff or share a link with the inputs.

Worked examples

Footing mat or structural slab, 10 x 6 m, 15M at 300 each way

Input

10 x 6 m, cover 75 mm, 15M @ 300 mm each way, one mat, 12 m stock

Output

53 bars, 390.05 m, 612.4 kg; 37 stock bars of 12 m

The 9.85 m bars use one stock bar each and the 5.85 m bars pair up two to a bar. The 75 mm cover is the usual figure for concrete cast against earth.

Slab, 12 x 8 m, 10M at 300, from 6 m bars

Input

12 x 8 m, cover 50 mm, 10M @ 300 mm, one mat, 6 m stock, lap 40 diameters (452 mm)

Output

67 bars, 679.79 m, 533.6 kg; 94 laps; 118 stock bars of 6 m

Every run is longer than 6 m, so each bar needs one or two laps. Ordering 12 m bars, if your supplier and truck can handle them, removes most of the laps.

Background and insight

The bar count uses the fence-post rule: a clear width of W - 2c at spacing s holds floor((W - 2c) / s) + 1 bars, with a bar at each edge. Counting only (W - 2c) / s is the classic takeoff error that leaves you one bar short on every run. Bars along the length are spaced across the width, so the two directions swap dimensions.

When a bar run is longer than the stock length, it is made from n pieces that overlap by the lap length, so n pieces cover n x S - (n - 1) x lap and n = ceil((run - lap) / (S - lap)). The lap itself is a design value. ACI 318 sets tension lap splices at 1.0 or 1.3 times the development length, which depends on concrete strength, bar size, cover and position; 40 bar diameters is a common starting value on site drawings, not a code check. Cover also comes from the code: ACI 318 asks for 3 in where concrete is cast against and permanently exposed to earth, which is why footings use 3 in (75 mm).

Common use cases

  • Ordering steel for a slab on grade

    Turn a spacing note such as "#4 @ 12 in EW" into a piece count and a weight that a supplier can quote.

  • Checking a fabricator quote

    Compare the supplier's weight and bar list against an independent takeoff before the delivery arrives.

  • Footings and mat foundations

    Add hooks at each end and a second mat to estimate a spread footing or raft.

  • Comparing bar size against spacing

    Swap #4 at 12 in for #5 at 16 in and compare steel area per foot, weight and the number of bars to tie.

Tips and limitations

  • Grade 400W has controlled chemistry for welding; weld any bar only where the drawings allow it and to CSA W186.
  • Use chairs or bolsters to keep the bars at the specified cover; mesh pulled up during the pour rarely ends where it should.
  • Slabs and footings in houses follow Part 9 of your provincial code, which sets its own rules; follow the code and the engineer's drawings rather than this estimate.

Sources and further reading

  1. Reinforcing bars (rebar), CSA G30.18 Gr. 400R or 400W, Russel Metals. Canadian bar sizes 10M to 55M with mass in kg/m and nominal area.
  2. National Building Code of Canada 2025, National Research Council of Canada (Government of Canada Publications). The model code that references CSA A23.1 and A23.3 for concrete; your province's code may differ.
  3. Notice of intent: Carbon steel bars for concrete reinforcement (CSA G30.18), Standards Council of Canada. Scope of CSA G30.18, including the weldable W grades.
  4. CSA G30.18: Carbon steel bars for concrete reinforcement, CSA Group

Frequently asked questions

How much does 10M rebar weigh per metre?

0.785 kg per metre. 15M weighs 1.570 kg/m, 20M 2.355 kg/m, 25M 3.925 kg/m, 30M 5.495 kg/m and 35M 7.850 kg/m (CSA G30.18 nominal masses).

What size is 15M rebar?

Its nominal diameter is 16.0 mm and its nominal area 200 mm². The number in a Canadian bar name is a rounded diameter, so 10M is 11.3 mm and 25M is 25.2 mm.

Is 10M the same as #3 or #4 rebar?

Neither exactly. A US #3 bar is 9.5 mm (71 mm²) and #4 is 12.7 mm (129 mm²); 10M at 11.3 mm and 100 mm² sits between them. 15M (200 mm²) is close to a US #5 (200 mm²).

What lap length should I use for 15M bars?

Take it from the structural drawings. Splice lengths under CSA A23.3 depend on concrete strength, bar size, cover, spacing and position. The 40 bar diameters used here (about 640 mm for 15M) is only a starting value.

What is the difference between 400W and 400R rebar?

Both have a 400 MPa specified yield strength under CSA G30.18. W grades have limits on chemistry and carbon equivalent for better weldability and ductility; R is the general-purpose grade.

Is there an in-depth guide to the Rebar Calculator?

Yes. “Rebar Takeoff for Slabs: Bar Counts, Laps, Cutting and Weight” covers the background, how it works, common pitfalls and worked examples. Read the full guide.