Canada version. Works in metres, millimetres and metric tonnes, the way Canadian asphalt plants sell hot mix, with square feet shown and Ontario municipal driveway specs as examples. US version
Asphalt Driveway Calculator (Metric Tonnes)
Metric tonnes of hot mix asphalt for a driveway or parking pad from the area and compacted thickness, with the 50 mm HL3 and 80 mm two-lift Ontario specs.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Asphalt Calculator?
Driveways in Canada are quoted by the square foot but the hot mix is sold by the metric tonne, so a contractor's quote is easiest to check in metric. This version uses metres, millimetres of compacted thickness and tonnes, and shows the area in square feet as well. At the default compacted density of 2,320 kg/m³, each 10 mm of asphalt weighs 23.2 kg per square metre.
Municipal specifications give a feel for the thickness. The Township of Oro-Medonte asks for 50 mm of HL3 asphalt over 150 mm of Granular A for a single-family driveway entrance, and Toronto builds the residential driveway in the boulevard with 80 mm of asphalt in two 40 mm lifts over 150 mm of Granular A. Run the tool once per lift and add them, or enter the total thickness.
- Rectangle, circle, triangle, trapezoid or known area
- Editable compacted density with typical ranges for hot mix
- Short tons and metric tonnes with automatic price conversion
- Spread rate, truckloads and a thickness comparison table
- Copy, share link and reset; nothing leaves your browser
Updated
How to use the Asphalt Calculator
- Choose imperial or metric and the shape of the area to pave.
- Enter the dimensions, or pick Known area and type the area from a site plan.
- Enter the compacted thickness and check the density against your supplier's mix data.
- Add a waste allowance for edges, low spots and handwork, usually 3 to 10%.
- Enter the price per ton or tonne and the truck capacity to see cost and loads, then copy the result.
Worked examples
Double driveway, 12 x 3.6 m at 50 mm
Input
43.2 m² (465 ft²), 50 mm compacted, 2,320 kg/m³, 5% extra
Output
2.16 m³; 5.26 tonnes
This matches a 50 mm HL3 surface like the Oro-Medonte entrance standard. Ask the contractor what size of truck the plant sends before counting loads.
Same driveway with two 40 mm lifts
Input
43.2 m², 80 mm compacted, 2,320 kg/m³, 5% extra
Output
3.46 m³; 8.42 tonnes
Going from 50 to 80 mm adds 60% more asphalt. The extra thickness is common where the driveway carries heavier vehicles or crosses the municipal boulevard.
Background and insight
Asphalt plants and agency specifications describe placement as a spread rate. At 145 lb/ft³, one square yard one inch thick is 9 x (1/12) x 145 = 108.75 lb, which is why estimators use about 110 lb per square yard per inch. The same rule in metric is about 23 kg per square metre for each 10 mm. Compacted density, not the loose density in the truck, is what matters: the paver lays the mat loose and the rollers compact it by roughly 20 to 25% in thickness to reach the target air voids, typically around 7% in place for dense-graded mixes.
US suppliers quote short tons of 2,000 lb; most other countries use metric tonnes of 1,000 kg, and 1 tonne is 1.102 short tons. The calculator converts the price and truck capacity when you switch units so a quote stays comparable. Residential driveways are commonly 2 to 3 in (50 to 75 mm) of surface course on a compacted aggregate base; parking lots and roads carrying trucks need a pavement design, for example by the AASHTO method.
Common use cases
Driveway quotes
Check that a contractor's tonnage matches the area and thickness they propose.
Patching and overlays
Order the right amount of hot mix or cold patch for potholes and trench reinstatement.
Parking lots and site roads
Compare a 2 in and a 3 in surface course in tonnage and cost.
Trucking plans
Work out how many loads to schedule so the paver is never waiting for material.
Tips and limitations
- Frost heave, not the asphalt, ruins most driveways: the compacted granular base and drainage matter more than an extra 10 mm on top.
- Work in the boulevard between the sidewalk and the road usually needs a municipal permit and follows the city's own specification.
- Hot mix plants in most of Canada shut down over the winter, so book paving for the warmer months.
Sources and further reading
- Construction specification for hot mix asphalt sidewalks, boulevards and driveways (TS 3.30), City of Toronto. Residential asphalt driveway: 150 mm Granular A and 80 mm in two 40 mm lifts.
- Development engineering standards: entrances, Township of Oro-Medonte. Single-family residential: 50 mm HL3 over 150 mm Granular A.
Frequently asked questions
How many tonnes of asphalt do I need for a driveway?
Area in m² x thickness in metres x 2.32 tonnes per m³, plus a few percent for edges. A 43.2 m² (465 ft²) driveway at 50 mm needs about 5.3 tonnes with 5% extra; at 80 mm, about 8.4 tonnes.
How thick should an asphalt driveway be in Ontario?
Municipal specs give a guide: Oro-Medonte asks for 50 mm of HL3 over 150 mm of Granular A for a single-family entrance, and Toronto uses 80 mm in two 40 mm lifts over 150 mm of Granular A for residential driveway work in the boulevard.
What is HL3 asphalt?
HL3 is a fine-graded hot mix surface course used across Ontario for driveways, parking lots and residential streets; HL8 is a coarser base course. Many municipalities now also specify Superpave mixes such as Superpave 9.5 and 12.5.
How much does a tonne of asphalt cover?
At 2,320 kg/m³, one tonne covers about 8.6 m² (93 ft²) at 50 mm and 5.4 m² (58 ft²) at 80 mm.
Is a tonne the same as a ton?
No. Canadian plants sell by the metric tonne of 1,000 kg. A US short ton is 907 kg, so a price per short ton looks about 10% lower for the same asphalt.
Is there an in-depth guide to the Asphalt Calculator?
Yes. “Asphalt Tonnage: From Square Feet and Inches to Tons of Hot Mix” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.