Press Brake Tonnage in Tonnes for S275, S355 and SWG Sheet

Bending force in tonnes per metre for S275 and S355 plate and SWG sheet, how to pick the V-die, the inside radius it gives, and what PUWER asks of press brakes.

By · · 10 min read

Illustration for the Press Brake Tonnage Calculator guide

United Kingdom edition. Written for UK fabrication shops: metric tonnes and kN, BS EN 10025-2 strengths for S275 and S355, SWG sheet thicknesses, and the PUWER power press rules for mechanical press brakes. US edition

A UK shop quoting a bending job usually knows three things: the grade (most often S275 or S355 to BS EN 10025-2), the thickness in millimetres or an SWG number for sheet, and the length of the bend. The brake is rated in metric tonnes, and so is the tooling, per metre. The question is whether this bend fits both, and what radius and flange the die will leave. This edition answers it in tonnes with the press brake tonnage calculator set up for S275, then covers the rules that apply to the brake itself under PUWER.

The formula in metric units

The rule behind most tonnage charts is written for inches and US tons: 575 x T² / V tons per foot for a 90° air bend in mild steel of 60,000 psi (414 N/mm²) tensile strength. Converted to the units a UK shop uses, and scaled for the material:

tonnes per metre ≈ 0.163 x UTS x T² / V      (T and V in mm, UTS in N/mm²)
kN per metre     ≈ 1.6 x UTS x T² / V
total tonnes     = tonnes per metre x bend length in metres

The 0.163 is simply the 575 constant with inches, US tons and feet converted to millimetres, tonnes and metres, and the 60 ksi baseline replaced by the actual tensile strength. The calculator does the same sum from millimetres and N/mm². The part to remember: force rises in direct proportion to tensile strength and to the square of thickness, and falls in proportion to the die opening. Double the thickness and you need four times the force in the same ratio of die.

Which tensile strength to type for S275 and S355

The SCI's steel material properties page gives the BS EN 10025-2 minimum tensile strengths: 410 N/mm² for S275 and 470 N/mm² for S355, for thicknesses over 3 mm and up to 100 mm. Plate of exactly 3 mm sits just below that band, and the SCI table does not list the figure for 3 mm and under, so the 3 mm examples below use the 410 and 470 minimums as working values; the mill certificate is the figure to trust at that thickness. Two things follow.

  • The minimum is a floor. Real plate is often stronger, and a 3 mm part bent on the assumption of 410 N/mm² will need more force if the mill certificate says 520. Plan with the certificate figure when you have it.
  • S355 needs about 15% more force than S275 at their minimums (470 / 410 = 1.146), before any difference in actual strength.

For a 3 mm, 2.5 m bend in a 24 mm die (8 x T):

Tensile strength usedTotal forcePer metrekN
410 N/mm² (S275 minimum)62.60 t25.04 t/m613.9 kN
470 N/mm² (S355 minimum)71.77 t28.71 t/m703.8 kN
520 N/mm² (a strong certificate)79.40 t31.76 t/m778.6 kN

On an 80 tonne brake, the same drawing goes from comfortable to marginal depending on which grade turns up and how strong the heat is. That is the case for reading the certificate before loading the job.

Choosing the V-die

The calculator starts from the usual rule: a V opening of 8 x T for thicknesses below 12.7 mm (half an inch) and 10 x T above it. The result rarely matches a die you own exactly, so pick the nearest one and type its opening in. Openings from about 6 to 12 x T work; narrower raises the force sharply and risks cracking the outside of the bend in higher-strength steel, wider makes a larger radius and a less consistent angle.

Here is a heavier job: 6 mm S355, 3 m long, on a brake of 150 tonnes.

DieV / TForcePer metreInside radiusMinimum flange
50 mm8.3165.35 t55.12 t/mabout 8.0 mmabout 35 mm
63 mm10.5131.23 t43.74 t/mabout 10.1 mmabout 44 mm

The 50 mm die needs more than the brake can give over 3 m. Moving up to 63 mm brings it within capacity, at the cost of a radius about 2 mm larger and a minimum flange about 9 mm longer. Check both against the drawing before you commit, and feed the larger radius into the bend allowance calculator, or the blank will come out the wrong length.

Short bends and the tooling rating

Now take the same 6 mm S355 in the 50 mm die, but only 300 mm long. The total drops to 16.53 t, a small fraction of a 150 tonne brake. The force per metre does not change: it is still 55.12 t/m, and that is the number to check against the rating stamped on the punch and die. A short, heavy bend in the middle of the bed concentrates the load on a short length of tooling, which is how dies get cracked on brakes that are nowhere near their total rating. Spread multiple short parts along the bed where the tooling allows, and keep off-centre loads within the maker's limits.

SWG sheet and stainless

Sheet is still sometimes specified by SWG. The calculator's gauge converter reads 16 SWG as 1.626 mm and 14 SWG as 2.032 mm. A 2.5 m bend in 14 SWG mild steel in a 16 mm die needs 43.50 t (17.40 t/m), with an inside radius of about 2.6 mm. For 2 mm stainless 304 at 586 N/mm², 1.5 m in a 16 mm die needs 35.79 t and forms a radius of about 3.4 mm, because stainless air-forms a larger radius, around 21% of V against about 16% for mild steel.

Bottoming the 3 mm S275 bend from the first table would need about five times the air-bend force, 313 t for the 2.5 m length. That multiplier is why air bending is the normal method for plate, and why bottoming is kept for thin sheet where the extra force is affordable.

PUWER and the brake itself

Whether the brake counts as a "power press" in law depends on how it is driven. HSE's Safe use of power presses (L112) sets out how regulations 32 to 35 of the Provision and Use of Work Equipment Regulations 1998 apply. In it:

  • A power press is a press or press brake for working metal that is power driven and has a flywheel and clutch. Mechanical press brakes are in; presses with no clutch mechanism, such as hydraulic and pneumatic ones, are outside regulations 32 to 35.
  • A power press and its guards must be thoroughly examined at least every 12 months if it has fixed guards only, and at least every 6 months otherwise, and after exceptional circumstances that could affect safety.
  • A mechanical brake must not be used after the first four hours of a working period unless it has been inspected and tested, and a certificate given, by an appointed person.
  • Records of thorough examinations are kept for at least two years, and inspection certificates for six months.

A hydraulic brake falls outside those four regulations, but the general PUWER duties on guarding, maintenance, information and training still apply to it. If you are not sure which drive your brake has, check the maker's documentation before relying on either regime.

Frequently asked questions

How many tonnes does it take to bend 3 mm S275?

About 25 tonnes per metre in a 24 mm die at the 410 N/mm² minimum tensile strength, so 62.6 tonnes for a 2.5 m bend. S355 at its 470 N/mm² minimum needs about 28.7 t/m. Use the mill certificate figure if it is higher, because the force scales with it.

Why does the per-metre figure matter if the brake has spare capacity?

Punches and dies are rated in tonnes per metre. A 300 mm bend in 6 mm S355 needs only 16.5 t in total but still loads the tooling at 55 t/m. If that exceeds the stamped rating, the die can crack or the beds can deflect even though the press is lightly loaded overall.

Does a hydraulic press brake need six-monthly thorough examinations?

Not under the power press regulations. HSE's L112 says regulations 32 to 35 apply to presses and press brakes with a flywheel and clutch, and not to presses without a clutch mechanism such as hydraulic ones. General PUWER duties, including suitable guarding and maintenance, still apply.

What V-die should I use for 6 mm plate?

The 8 x T rule gives 48 mm, so a 50 mm die is the usual starting point. If the force is too high for your brake over the bend length, a 63 mm die cuts it by about a fifth but increases the inside radius to around 10 mm and the minimum flange to about 44 mm.

Sources and further reading

Open the Press Brake Tonnage Calculator

More Sheet Metal & Welding

Every tool in the Sheet Metal & Welding section, free and in your browser.