Press Brake Tonnage Calculation for MS Sheet and Plate
Bending force in tonnes for MS and GI sheet in SWG and IS 2062 plate over an 8 ft bend, how to pick the V-die, and the power press rules for press brakes.
By Redbison Dev · · 10 min read

India edition. Written for Indian fabrication shops: 8 ft (2440 mm) sheet lengths, SWG gauges, IS 2062 E250 and E350 tensile strengths, and the power press schedule of the Model Rules under the Factories Act. US edition
Most press brake jobs in Indian sheet metal shops start with an 8 x 4 ft sheet, so the bend length that decides the machine is usually 2440 mm. Thickness arrives either as an SWG number (16 and 14 gauge MS and GI for panels, ducting and enclosures) or in millimetres for IS 2062 plate. The force you need goes up with the square of that thickness and with the steel's tensile strength, and comes down as the V-die gets wider. This edition gives the numbers in tonnes with the press brake tonnage calculator for MS sheet and then covers how Schedule VI of the Model Rules treats the machine.
The calculation in shop units
The working rule is the American air-bending formula, 575 x T² / V tons per foot for a 90° bend in steel of 414 N/mm² (60 ksi) tensile strength. Converted to millimetres and metric tonnes:
tonnes per metre ≈ 0.163 x UTS x T² / V (T, V in mm; UTS in N/mm²)
total tonnes = tonnes per metre x bend length in metres
For 2 mm MS at 414 N/mm² in a 16 mm die that is 0.163 x 414 x 4 / 16, about 16.9 t/m, or 41 tonnes for the full 2.44 m. The calculator does the arithmetic and adds kN, the inside radius and the minimum flange.
SWG sheet over the full 8 ft
The calculator's gauge table gives 16 SWG as 1.626 mm and 14 SWG as 2.032 mm (British Standard Wire Gauge). With the mild steel preset of 414 N/mm²:
| Sheet | Die | Force over 2440 mm | Per metre | Inside radius |
|---|---|---|---|---|
| 16 SWG (1.626 mm) MS or GI | 12 mm | 36.23 t | 14.85 t/m | about 1.9 mm |
| 14 SWG (2.032 mm) MS or GI | 16 mm | 42.46 t | 17.40 t/m | about 2.6 mm |
| 1.5 mm stainless 304 (586 N/mm²) | 12 mm | 43.66 t | 17.90 t/m | about 2.5 mm |
GI sheet bends with the force of its steel base; the zinc coating adds nothing meaningful to the tonnage. Stainless needs about 40% more force than MS of the same thickness and forms a larger radius, around 21% of V instead of 16%.
Bottoming instead of air bending multiplies the force by about five: the same 16 SWG bend would need about 181 tonnes. That is why air bending is the normal choice even on thin sheet when the bend runs the full length.
IS 2062 plate: E250 against E350
For structural plate, use the tensile strength on the mill test certificate. The minimums in Table 2 of IS 2062:2011 are:
| Grade | Minimum tensile strength | Minimum yield, under 20 mm |
|---|---|---|
| E250 | 410 N/mm² | 250 N/mm² |
| E275 | 430 N/mm² | 275 N/mm² |
| E300 | 440 N/mm² | 300 N/mm² |
| E350 | 490 N/mm² | 350 N/mm² |
| E410 | 540 N/mm² | 410 N/mm² |
A 6 mm plate bent over 2440 mm shows what the grade does to the machine you need:
| Plate and die | Force | Per metre | Inside radius | Minimum flange |
|---|---|---|---|---|
| E250, 50 mm die | 117.31 t | 48.08 t/m | about 8 mm | about 35 mm |
| E350, 50 mm die | 140.20 t | 57.46 t/m | about 8 mm | about 35 mm |
| E350, 63 mm die | 111.27 t | 45.60 t/m | about 10.1 mm | about 44 mm |
On a 125 tonne brake, the E250 job runs and the E350 job in the same die does not. A 63 mm die brings E350 back under 125 tonnes, but the radius grows by about 2 mm and the flange must be about 9 mm longer. Check the drawing allows that before changing the die, and use the real radius in the bend allowance calculator when you cut the blank.
Picking the V-die and checking the tooling
The calculator's default die opening is 8 x T below 12.7 mm thickness and 10 x T above. Choose the nearest V you have and type it in: about 6 to 12 x T is usable. A narrower die raises the force and can crack the outside of the bend in high-tensile plate; a wider one gives a larger radius and more variation in angle.
Tooling is rated in tonnes per metre, and that rating, not the press total, is often the first limit. A 10 mm E250 plate 1250 mm long in a 100 mm die needs 83.47 t in total, which a 100 tonne brake can give, but that is 66.78 t/m on the punch and die. Check the figure stamped on your tooling, and keep a heavy short bend centred on the bed.
For holes punched before bending, the punching force calculator gives the tonnage for the turret or power press in the same units.
Schedule VI of the Model Rules: press brakes are power presses
DGFASLI publishes Model Rules under the Factories Act, 1948, and Schedule VI (Power Press) of those Model Rules says it applies to all types of power presses including press brakes, except when used for working hot metal. Among its requirements:
- No power press may be used unless it has been thoroughly examined and tested by a competent person within the preceding 12 months, and a new press is examined and tested after installation before first use.
- Every safety device other than fixed fencing must have been examined and tested within the preceding six months, in position on the press.
- The competent person makes a report of each examination and test, and it is kept readily available for inspection.
- Each press has a fixed guard enclosing the front and sides of the tool, or an automatic or interlocked guard in its place, kept in efficient working order; the press must not be run while that guard is defective.
Your state's factory rules may differ in detail from the Model Rules. The Ministry of Labour and Employment announced that the Occupational Safety, Health and Working Conditions Code, 2020 and the other three labour codes are effective from 21 November 2025, and that during the transition the relevant provisions of the existing labour Acts and their rules stay in force. Confirm with your state's Inspector of Factories which rules your works must follow now.
Frequently asked questions
How much tonnage is needed to bend 2 mm MS sheet 8 feet long?
About 41 tonnes in a 16 mm die with the mild steel preset of 414 N/mm², which is about 16.9 tonnes per metre. For 14 SWG (2.032 mm) in the same die the force is 42.46 tonnes over 2440 mm. Halving the bend length halves the total, but the load per metre on the tooling stays the same.
Which tensile strength should I use for IS 2062 plate?
Use the value on the mill test certificate. If you do not have one, use the IS 2062 minimum for the grade: 410 N/mm² for E250 and 490 N/mm² for E350. Remember that a minimum is a floor, so real plate can need more force than the estimate.
Does a press brake need a yearly examination in India?
Under Schedule VI of the Model Rules framed under the Factories Act, yes: a power press, including a press brake, must be thoroughly examined and tested by a competent person within every 12 months, and its safety devices other than fixed fencing every six months. Check your state's own rules.
What thickness can a 100 tonne press brake bend over 8 feet?
In MS with an 8 x T die, about 4 mm: 3 mm needs around 62 tonnes over 2440 mm, 4 mm about 82 tonnes and 5 mm about 103, over the limit. In E350 plate the limit is lower because the force rises with tensile strength. Always check the maker's chart for your dies.
Sources and further reading
- Model Rules under the Factories Act, 1948, DGFASLI, Ministry of Labour and Employment. Schedule VI, Power Press: press brakes included, 12-month examination, six-monthly safety devices, fixed or automatic or interlocked guards.
- Four Labour Codes made effective from 21 November 2025 (press release), Press Information Bureau, 21 November 2025. The codes effective from 21 November 2025; existing Acts and rules continue during the transition.
- IS 2062:2011 Hot rolled medium and high tensile structural steel, Bureau of Indian Standards (public copy). Table 2 tensile and yield strengths by grade.
- Die width selection, The Fabricator. V opening against thickness.
- Predicting the inside radius when bending with the press brake, The Fabricator. The radius as a share of the die opening.
- ASM Handbook Volume 14B: Metalworking: Sheet Forming, ASM International. Bending mechanics.
Open the Press Brake Tonnage Calculator
More Sheet Metal & Welding
Every tool in the Sheet Metal & Welding section, free and in your browser.