Press Brake Tonnage for MS Plate: PS 4798 and SWG Sheet

How many tonnes a press brake needs for MS sheet and PS 4798 plate, why the 400 to 550 N/mm² tensile range matters, and how to choose the V-die and flange.

By · · 10 min read

Illustration for the Press Brake Tonnage Calculator guide

Pakistan edition. Written for Pakistani fabrication shops: tonnes over 8 ft and 4 ft bends, SWG sheet, the 400 to 550 N/mm² tensile range of PS 4798 structural steel and the PSQCA compulsory standards list. US edition

The hardest number in a press brake estimate in Pakistan is not the thickness or the bend length. It is the tensile strength of the plate on the day. PS 4798, the Pakistan Standard for carbon structural steel, allows plate from 400 to 550 N/mm², and the bending force rises in step with it, so the same drawing can need 37.5% more tonnage depending on which end of the range arrives. This edition shows how to plan for that with the press brake tonnage calculator in tonnes, then works through die choice, sheet in SWG and the per-metre limit of the tooling.

The rule, converted to tonnes and millimetres

The standard air-bending rule is 575 x T² / V tons per foot for a 90° bend in steel of 414 N/mm² (60 ksi). In the units of a Pakistani shop floor it becomes:

tonnes per metre ≈ 0.163 x UTS x T² / V     (T and V in mm, UTS in N/mm²)
total tonnes     = tonnes per metre x bend length (m)

Three things move the answer. Force goes up with the square of thickness, in direct proportion to tensile strength and to bend length, and down in proportion to the V opening.

What PS 4798 allows

PS 4798:2017 (Rev), Carbon Structural Steel is based on ASTM A36/A36M-14. Its Table 2 sets, for plates, shapes and bars, a tensile strength of 400 to 550 MPa (58 to 80 ksi) and a minimum yield point of 250 MPa (36 ksi), with at least 20% elongation in 200 mm and 23% in 50 mm for plates and bars. Structural steel to PS 4798 is on PSQCA's list of compulsory items to meet Pakistan Standards, along with hot-rolled and cold-reduced carbon steel sheet (PS-ISO 3573 and 3574).

A range that wide is the reason to plan for the top unless a mill test certificate says otherwise. For a 4 mm plate bent along a full 8 ft sheet (2440 mm):

DieUTSForcePer metreInside radiusMinimum flange
32 mm (8 x T)400 N/mm²79.48 t32.57 t/mabout 5.1 mmabout 22 mm
32 mm (8 x T)550 N/mm²109.29 t44.79 t/mabout 5.1 mmabout 22 mm
40 mm (10 x T)550 N/mm²87.43 t35.83 t/mabout 6.4 mmabout 28 mm

A 100 tonne brake bends soft plate in the 32 mm die and stalls on hard plate from the same standard. With no certificate, either shorten the bend, widen the die to 40 mm (accepting a larger radius and a 28 mm flange), or put the job on a bigger machine.

Shorter bends and heavy plate

Halve the length and you halve the total, but not the per-metre load. Two more cases:

  • 5 mm plate, 6 ft (1830 mm), 40 mm die, 550 N/mm²: 102.46 t in total and 55.99 t/m. Just over a 100 tonne brake, and a heavy load per metre on standard tooling.
  • 12 mm plate, 1 m, 120 mm die (10 x T): 107.50 t at 550 N/mm² and 78.18 t at 400 N/mm², the same in tonnes per metre because the bend is exactly 1 m. The inside radius is about 19 mm and the minimum flange about 84 mm.

Check the per-metre figure against the rating stamped on the punch and die as well as the press total. Short heavy bends in the middle of the bed are how dies crack on machines that are nowhere near full load.

Sheet in SWG

Sheet is still bought by gauge. The calculator reads 16 SWG as 1.626 mm and 14 SWG as 2.032 mm. With the mild steel preset of 414 N/mm²:

Sheet and bendDieForcePer metre
16 SWG, full 8 ft (2440 mm)12 mm36.23 t14.85 t/m
14 SWG, 4 ft (1220 mm)16 mm21.23 t17.40 t/m

If the supplier's "16 gauge" is in fact US Manufacturer's Standard Gauge rather than SWG, it is 1.519 mm instead of 1.626 mm, and the same 8 ft bend needs 31.63 t instead of 36.23 t. The sheet metal gauge converter shows both tables, so measure the sheet with a micrometer when the label is unclear.

Choosing the V-die

The calculator's default opening is 8 x T for thicknesses under 12.7 mm and 10 x T from there up. Practical limits are about 6 to 12 x T:

  • Narrower than 6 x T raises the force steeply, marks the part and can crack the outside of the bend, a bigger risk with harder plate.
  • Wider than 12 x T gives a large radius and an angle that wanders with small changes in thickness and strength.

The inside radius in air bending is set by the die, not the punch, unless the punch tip is larger than the natural radius. For mild steel the calculator uses 16% of V, so a 32 mm die leaves about 5.1 mm. Use that real radius in the bend allowance calculator when cutting blanks.

Bottoming needs about five times, and coining about ten times, the air-bending force. On plate that rules them out on most brakes; the 4 mm job above would need over 500 tonnes bottomed at 550 N/mm².

Frequently asked questions

How many tonnes does a press brake need to bend 4 mm plate 8 ft long?

In a 32 mm die, about 79.5 tonnes if the plate is at 400 N/mm² and about 109.3 tonnes at 550 N/mm², the two ends of the PS 4798 range. A 40 mm die brings the hard-plate figure down to about 87.4 tonnes, with a larger inside radius.

What tensile strength should I use for PS 4798 plate?

The value on the mill test certificate. PS 4798 allows 400 to 550 N/mm² for plates, shapes and bars, with a minimum yield of 250 N/mm². If you have no certificate, plan for 550 N/mm², because the force rises in proportion to tensile strength.

Is PS 4798 the same as ASTM A36?

PS 4798:2017 is based on ASTM A36/A36M-14, and its tensile requirement for plates, shapes and bars matches A36 at 58 to 80 ksi (400 to 550 MPa). It is on PSQCA's list of compulsory items to meet Pakistan Standards, so structural steel sold as PS 4798 should meet it.

How do I convert press brake tonnes to kN?

Multiply metric tonnes by 9.807. The 109.29 tonne bend above is about 1,072 kN. The calculator shows tonnes, kN and US tons together, which helps when an imported brake's chart is in US tons.

Sources and further reading

Open the Press Brake Tonnage Calculator

More Sheet Metal & Welding

Every tool in the Sheet Metal & Welding section, free and in your browser.