United Kingdom version. Metric for UK garden decking: 144 mm boards sold in 3.6 and 4.8 m lengths, 47 mm joists at 400 mm, screws per m² and prices in pounds. US version

Decking Calculator (UK)

Work out decking boards by the 3.6 or 4.8 m length, joists at 400 mm, screws and a cost in pounds for a garden deck measured in metres, with the planning rules.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Deck Calculator?

UK merchants sell softwood decking boards by the length, typically 120 or 144 mm wide and 28 to 32 mm thick in 2.4, 3.6 and 4.8 m lengths, with 47 mm treated joists for the frame. Most garden decks are freestanding on posts or pads rather than bolted to the house. This version starts with a 4.8 x 3.6 m freestanding deck in those sizes.

Choosing the board length is where money is saved. A deck whose length divides into the board length wastes nothing, while a 3.0 m deck in 3.6 m boards throws away 0.6 m from every board. The calculator nests short rows into one board, so try each stock length and compare the board count.

Under permitted development, a deck needs no planning permission when it is no more than 30 cm above the ground and, with other extensions and outbuildings, covers no more than half the garden. Higher decks need permission, decks at listed buildings need permission, and designated areas have tighter limits; check with the planning department.

  • Rows and boards by stock length, with nesting of short rows
  • Straight or diagonal decking and adjustable waste
  • Joists, rim, ledger, beam plies, posts and hangers
  • Face screws or hidden clips per crossing, with boxes and rate per area
  • Cut list, joist span readout, decking cost, metric and imperial
Read the guide: Estimating a Deck: Boards, Joists, Screws and Span Tables

Updated

How to use the Deck Calculator

  1. Choose imperial or metric and enter the deck length along the house and the projection out from it.
  2. Enter the actual board width, the gap between boards and the board length you will buy, then choose straight or diagonal boards.
  3. Set the joist spacing, joist size label and stock length, the rim thickness, and whether a ledger attaches the deck to the house.
  4. Enter the beams, plies, posts and the joist cantilever past the beam from your design or permit drawing.
  5. Choose face screws or hidden clips, the count per box and the waste, then read the materials and cut list.

Worked examples

Freestanding 4.8 x 3.6 m garden deck

Input

144 mm boards, 5 mm gaps, 4.8 m lengths, joists 47 mm at 400 mm, two beams with three posts each, two screws per joist, 10% extra, £20 a board

Output

25 rows, 28 boards (120 m net); 13 joists at 3553 mm; 650 screws (about 38 per m², 2 boxes of 500); about £560 of boards

Each 4.8 m board spans the full length, so there are no butt joints. Joist size and the post spacing come from the decking supplier's or designer's span guidance.

Small 2.4 x 2.4 m deck from 4.8 m boards

Input

Same boards, 2.4 x 2.4 m, 4.8 m lengths cut in half, £20 a board

Output

17 rows from 10 boards (40.8 m net); 7 joists; 238 screws; £200

Two rows come out of each board with no offcut, which is why 2.4 m and 4.8 m decks are the cheapest to board.

A 3.0 x 3.0 m deck in 3.6 m boards

Input

144 mm boards, 5 mm gaps, 3.6 m lengths at £15

Output

21 rows, 24 boards (63 m net of 86.4 m bought); 378 screws; £360

Every board loses 0.6 m. Offcuts can make the fascia or step treads, otherwise a 2.4 or 3.6 m deck size would use the boards better.

Background and insight

Joists are counted like studs: ceil(length / spacing) + 1 including both end joists. Rows of decking are ceil(projection / (board width + gap)), using the actual width. A 5/4x6 board is 5-1/2 in wide, so with a 3/16 in gap each row covers 5-11/16 in. When the deck is shorter than the boards, rows nest two or more to a board; when it is longer, butt joints have to land on joists and each row takes more than one board. Two face screws per board at every joist is the standard pattern, a little over 3 screws per square foot for 5-1/2 in boards at 16 in, and hidden clips use one per crossing.

Joist sizes and spans are a code question. In the US, IRC Section R507 holds the deck joist and deck beam span tables, which depend on species, grade, spacing and cantilever, and the American Wood Council publishes the same rules as DCA 6. Composite decking makers often require 12 in joist spacing for diagonal boards. The calculator shows your joist span so you can compare it with the table, but it does not size members.

Common use cases

  • Pricing a deck before a permit

    Get board, joist and fastener counts to compare composite and timber quotes.

  • Planning a resurface

    Count new boards and screws for existing framing by entering the deck size and joist spacing.

  • Choosing board direction

    Compare straight and diagonal layouts for board count, waste and fasteners.

  • Ordering stock lengths

    Try 12, 16 and 20 ft boards to find the length that nests best with your deck size.

Tips and limitations

  • Lay a weed-control membrane and gravel under a ground-level deck and leave a gap for air to move under the boards.
  • Fix boards with two screws at every joist, about 15 mm from the edges, and pre-drill near board ends to stop splitting.
  • Seal every cut end of treated timber with an end-grain preservative, because the treatment does not reach the centre of the board.

Sources and further reading

  1. Decking: planning permission, Planning Portal. The 30 cm height and 50% garden limits for permitted development.
  2. The Buyer's Guide to Preservative Treated Wood (Issue 6), Wood Protection Association. Use Class 3 for deck boards, Use Class 4 for decking posts, joists and beams.

Frequently asked questions

Do I need planning permission for decking?

Not under permitted development if the deck is no more than 30 cm above the ground and, together with other extensions and outbuildings, covers no more than 50% of the garden. Raised decks, balconies and verandas, and decks at listed buildings or in National Parks, the Broads and other designated areas have tighter rules.

How many decking boards do I need for a 4.8 x 3.6 m deck?

With 144 mm boards and 5 mm gaps the 3.6 m width takes 25 rows, and 4.8 m boards run the full length, so 25 boards plus 10% gives 28. Narrower 120 mm boards need more rows.

Which treatment class do decking boards and joists need?

The Wood Protection Association guide to BS 8417 puts deck boards in Use Class 3 (outdoors, above the ground) and decking posts, joists and beams in Use Class 4, which covers ground contact and exterior structural support. Ask the merchant to confirm the use class in writing.

How far apart should decking joists be?

The board maker states the maximum joist span for its product, so take the spacing from its data. The calculator opens at 400 mm centres; diagonal boards and thin composite boards usually need closer joists.

How many decking screws per square metre?

With two screws at every joist crossing, 144 mm boards on joists at 400 mm take about 38 screws per m² over a whole deck. Narrower boards or closer joists need more; the calculator counts the crossings for your layout.

Should a garden deck be fixed to the house wall?

A ledger fixed to the wall must stay well below the damp-proof course and must not bridge it or block air bricks. That is why many UK decks are freestanding with their own posts next to the house; untick the ledger box for that layout.

Is there an in-depth guide to the Deck Calculator?

Yes. “Estimating a Deck: Boards, Joists, Screws and Span Tables” covers the background, how it works, common pitfalls and worked examples. Read the full guide.