United Kingdom version. Metric throughout, with UK section names (UB, UC, SHS to EN 10219 and EN 10210), B500B bar sizes, prices in pounds and the HSE lifting rules that need a known load weight. US version

Steel Weight Calculator (UK)

Weight of UK universal beams and columns, SHS, RHS, flats and B500B rebar in kg per metre and per length, with the Blue Book and BS 4449 figures to check against.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Steel Weight Calculator?

UK steelwork is ordered by serial size and mass per metre. A 203 x 133 x 25 UB is a universal beam with a nominal 203 mm depth, 133 mm width and 25 kg per metre, so most of the time the weight is already in the name. This calculator is for everything else: odd lengths, a whole delivery, flats and plate cut to size, hollow sections with the right corner radii, and bundles of reinforcing bar.

Enter a rolled section as an I-beam using the Blue Book depth, width, web and flange thickness, and the tool gives the parallel-flange weight without the root fillets. For 203 x 133 x 25 UB that is 24.71 kg/m against the tabulated 25.1 kg/m, about 1.6% light, so for beams and columns use the table mass and keep the calculator for checking a quantity or a cut list. For SHS and RHS, pick cold-formed (EN 10219) or hot-finished (EN 10210) and the corner radii bring the result within about 1% of the tables.

Weights matter on site because of lifting. The Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) require every lift to be planned by a competent person, and a plan starts with the load. Use the calculated weight for estimating and the certified weight on the delivery note for the lift plan.

  • Plate, flat, round, square and hex bar, round tube, SHS, RHS, angle, channel and I-beam
  • EN 10219 and EN 10210 corner radii for hollow sections, or sharp corners
  • Weight per metre and per foot, per piece and in total, in kg and lb
  • Density presets for carbon and stainless steel, cast iron, aluminium, copper, brass and titanium, all editable
  • Comparison table for every material, surface area for coating, optional cost
Read the guide: Steel Weight Formulas for Plate, Bar, Pipe and Sections (kg/m and lb/ft)

Updated

How to use the Steel Weight Calculator

  1. Choose metric (mm, m, kg) or imperial (in, ft, lb). Switching converts the sizes you already entered.
  2. Pick the shape and enter its dimensions. Tubes need the outside size and the wall thickness.
  3. For square or rectangular tube, choose cold-formed, hot-finished or sharp corners.
  4. Enter the length of each piece and the quantity, then pick the material or type a density.
  5. Read the total, the weight of each piece, the weight per metre or foot and the surface area; add a price per kg or lb for a cost.

Worked examples

Eight 203 x 133 x 25 UB at 6 m

Input

I-beam 203.2 x 133.2 mm, web 5.7 mm, flange 7.8 mm, 6 m, quantity 8

Output

24.71 kg/m; 148.2 kg each; 1,186 kg in total

The Blue Book mass of 25.1 kg/m includes the root fillets, which puts the delivery at about 1,205 kg. Either way it is more than a tonne, so check the lorry crane or telehandler chart at the reach you need.

Fifty 16 mm B500B bars at 6 m

Input

Round bar 16 mm, 6 m, quantity 50

Output

1.578 kg/m; 9.47 kg each; 473.5 kg in total

Nominal bar mass is the nominal cross-section times 7,850 kg/m³, which is what the calculator works out. Bar is ordered and paid for by the tonne, so this is a quick check of a delivery ticket.

100 x 100 x 5 SHS, cold-formed or hot-finished

Input

Square tube 100 x 5 mm, 1 m, cold-formed then hot-finished corners

Output

14.41 kg/m cold-formed; 14.70 kg/m hot-finished

The same nominal size weighs about 2% more as an EN 10210 hot-finished section because its corners are tighter. Check which one is on the drawing before ordering.

Background and insight

Weight is simply cross-section area times length times density. The area formulas are exact for the idealised shapes: a round tube is π(D − t)t, an angle is t(a + b − t), and a hollow section with rounded corners is 2t(B + H − 2t) − (4 − π)(ro² − ri²). The ASME B36.10 pipe weight formula, 10.69(D − t)t in lb/ft with inches, is the same equation with the steel density folded in.

Carbon steel is taken as 7,850 kg/m³ (0.2836 lb/in³), the value EN 10025 and most section tables use. Stainless grades are heavier: EN 10088-1 gives 7,900 kg/m³ for 1.4301 (304) and 8,000 kg/m³ for 1.4401 (316). Aluminium alloys are about 2,700 kg/m³, copper C11000 about 8,890 kg/m³ and cartridge brass about 8,530 kg/m³. All of these are typical values at room temperature; enter your supplier's figure if it differs.

Real stock is never exactly nominal. Mill tolerances on plate thickness and bar diameter (EN 10029, ASTM A6) allow a few percent either way, and rolled beams, channels and angles have root fillets that add a little area. Use the theoretical weight for estimating and quoting, and the certified weight on the delivery note for lifting plans.

Common use cases

  • Quoting fabrication jobs

    Total the weight of plates, tubes and sections in a frame to price material and galvanising.

  • Lifting and transport

    Check that a bundle of bar or a stack of plate is within a crane, forklift or trailer limit.

  • Comparing materials

    See how much an aluminium or stainless version of the same part weighs before redesigning.

  • Estimating dead load

    Get kg per metre of a beam or rail to add self-weight to a structural load calculation.

Tips and limitations

  • UB and UC serial sizes name the nominal depth, width and mass; the actual depth differs (203.2 mm for a 203 x 133 UB), so take the dimensions from the table, not the name.
  • Steel prices are usually quoted per tonne in the UK; divide by 1,000 to enter a price per kg in pounds.
  • Galvanising adds weight, so ask the galvaniser for their figure if the finished weight matters for a lift.
  • For plate, 7.85 kg per square metre per millimetre of thickness is the number to remember: a 2.5 x 1.25 m sheet of 10 mm plate weighs 245 kg.

Sources and further reading

  1. Lifting Operations and Lifting Equipment Regulations 1998 (LOLER), Health and Safety Executive. Lifting operations must be planned by a competent person, supervised and carried out safely.
  2. Universal beams: dimensions and properties (Blue Book, BS EN 1993-1-1 with UK National Annex), Steel for Life and the Steel Construction Institute. 203 x 133 x 25 UB: 25.1 kg/m, h 203.2 mm, b 133.2 mm, tw 5.7 mm, tf 7.8 mm, Iy 2,340 cm⁴.
  3. Square hollow sections, cold-formed and hot-finished: dimensions and properties (Blue Book), Steel for Life and the Steel Construction Institute. 100 x 100 x 5.0 SHS: 14.4 kg/m cold-formed (EN 10219); the hot-finished (EN 10210) table gives 14.7 kg/m.

Frequently asked questions

How much does a 203 x 133 x 25 UB weigh per metre?

The Blue Book gives 25.1 kg/m. Entered as an I-beam with its actual dimensions (203.2 x 133.2 mm, 5.7 mm web, 7.8 mm flange) the calculator gives 24.71 kg/m because it leaves out the root fillets. Use 25.1 kg/m for ordering and lifting.

What is the weight of rebar per metre in the UK?

B500 bar to BS 4449 is sold in sizes from 8 to 40 mm, and its nominal mass is the nominal cross-section at 7,850 kg/m³. The calculator gives 0.395 kg/m for 8 mm, 0.617 for 10 mm, 0.888 for 12 mm, 1.578 for 16 mm and 3.853 for 25 mm; enter a quantity and length for the bundle total.

Does the weight of a steel beam need to be known for lifting?

Yes. Under LOLER every lifting operation has to be properly planned by a competent person, appropriately supervised and carried out safely, and the plan depends on knowing the load. The HSE guidance also covers lifting accessories such as chains and slings, which have their own safe working loads.

Why do cold-formed and hot-finished hollow sections weigh differently?

Cold-formed EN 10219 sections have larger outside corner radii than hot-finished EN 10210 ones, so they contain slightly less steel; the calculator models each corner type. The Blue Book lists a 100 x 100 x 5 SHS at 14.4 kg/m cold-formed and 14.7 kg/m hot-finished, and the calculator gives 14.41 and 14.70 kg/m.

How do I convert a steel price per tonne to a price per kg?

Divide by 1,000. A quote of £1,200 per tonne is £1.20 per kg; enter that in the price box and the calculator multiplies it by the total weight.

How heavy is a sheet of steel plate?

Each millimetre of thickness weighs 7.85 kg per square metre. An 8 x 4 ft sheet (2.44 x 1.22 m) of 6 mm plate is about 140 kg; enter the plate size to get the exact figure and the cost.

Is there an in-depth guide to the Steel Weight Calculator?

Yes. “Steel Weight Formulas for Plate, Bar, Pipe and Sections (kg/m and lb/ft)” covers the background, how it works, common pitfalls and worked examples. Read the full guide.