United Kingdom version. Uses UK section dimensions and Eurocode notation (Iy, Iz, Wel, Wpl), with worked comparisons against the Steel for Life Blue Book for UB and PFC sections. US version

Section Properties Calculator (UK, Eurocode 3)

Second moment of area, Wel and Wpl for UB, UC and PFC sections in mm and cm, checked against Blue Book values to Eurocode 3 and the UK National Annex.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Section Properties Calculator?

UK engineers look up rolled sections in the Blue Book (the SCI and Steel for Life section tables to Eurocode 3 with the UK National Annex), so this version shows what the calculator gives for the same UB and PFC sizes and how far it sits from the tabulated values. Enter the depth h, width b, web tw and flange tf from the table in millimetres.

Mind the axis names. Eurocode 3 calls the major axis y-y and the minor axis z-z, so the tool's Ix is Iy in the Blue Book and its Iy is Iz. The tool's elastic modulus S is Wel and its plastic modulus Z is Wpl. Results show in mm and cm, the units the tables use.

UK universal beams and parallel flange channels have parallel flanges, so a plate model gets the minor-axis values almost exactly; only the root radius is missing, which takes about 1.5% off the major-axis figures. That makes the tool a quick check on a table look-up or on a plated section that no table covers.

  • Eight shapes: rectangle, hollow rectangle, circle, tube, I-beam, T, channel and angle
  • Area, centroid, Ix, Iy, Sx and Sy at each fibre, Zx, Zy, rx and ry
  • Product of inertia, principal moments and minimum r for angles; polar moment J for circles and tubes
  • Scaled cross-section drawing with centroid and axes
  • Results in two units side by side, copy summary and share link
Read the guide: Moment of Inertia, Section Modulus and Radius of Gyration for Engineers

Updated

How to use the Section Properties Calculator

  1. Pick the shape and the unit you want to work in.
  2. Enter the dimensions shown for that shape. Flange widths, depths and thicknesses are outside dimensions; for tubes enter the outside diameter or size and the wall thickness.
  3. Check the drawing: the red dashed line is the x-x centroidal axis and the green one is y-y.
  4. Read the headline area, Ix, minimum Sx and Zx, then the full table with both units.
  5. For angles, use the principal values and the minimum radius of gyration for buckling checks. Copy the table or share the link.

Worked examples

UB 305 x 165 x 40

Input

I-beam: bf = 165.0, d = 303.4, tf = 10.2, tw = 6.0 mm

Output

A = 50.64 cm²; Iy = 8,370 cm⁴; Iz = 764.2 cm⁴; Wel,y = 551.8 cm³; Wpl,y = 613.6 cm³

The Blue Book gives A = 51.3 cm², Iy = 8,500 cm⁴, Iz = 764 cm⁴, Wel,y = 560 cm³ and Wpl,y = 623 cm³. The major-axis values come out about 1.5% low because the 8.9 mm root radius is left out; Iz matches.

UB 457 x 191 x 67

Input

I-beam: bf = 189.9, d = 453.4, tf = 12.7, tw = 8.5 mm

Output

A = 84.61 cm²; Iy = 28,980 cm⁴; Iz = 1,452 cm⁴; Wel,y = 1,278 cm³; Wpl,y = 1,452 cm³

Blue Book: 85.5 cm², 29,400 cm⁴, 1,450 cm⁴, 1,300 cm³ and 1,470 cm³. Again about 1.4% low on the major axis and level on the minor axis.

PFC 200 x 90 x 30

Input

Channel: bf = 90, d = 200, tf = 14.0, tw = 7.0 mm

Output

A = 37.24 cm²; Iy = 2,480 cm⁴; Iz = 310.9 cm⁴; Wel,y = 248.0 cm³; Wpl,y = 286.1 cm³

Blue Book: 37.9 cm², 2,520 cm⁴, 314 cm⁴, 252 cm³ and 291 cm³, all within 2%. Note the tool reports two minor-axis moduli for a channel because its centroid sits off the web.

Background and insight

The calculator splits each shape into rectangles, finds the centroid from the first moment of area, ȳ = ΣAy/ΣA, and then applies the parallel axis theorem, I = Σ(bh³/12 + A d²), to move each piece's own inertia to the common centroidal axis. Hollow shapes subtract the hole. Circles use the exact π D⁴/64. The product of inertia Ixy is computed the same way, and for angles Mohr's circle gives the principal values and the rotation of the principal axes.

The elastic section modulus S = I/c, with c the distance from the centroid to the extreme fibre, converts a bending moment into the maximum elastic stress, σ = M/S. The plastic modulus Z is the first moment of area about the plastic neutral axis, which divides the area into two equal halves; M = Fy Z is the moment at which the whole section has yielded. The ratio Z/S, the shape factor, is 1.5 for a rectangle, 1.70 for a solid circle and roughly 1.1 to 1.2 for I-beams bent about the strong axis. AISC calls these S and Z; Eurocode 3 calls them Wel and Wpl.

Rolled sections have root fillets between web and flange and rounded toes, which this tool ignores. The effect is small but real: an L4x4x1/2 angle calculated here has A = 3.75 in² and ȳ = 1.18 in, matching the AISC Manual, while Ix comes out at 5.56 in⁴ against the tabulated 5.52 in⁴, less than 1% apart.

Common use cases

  • Beam and column checks

    Get I for deflection, S for bending stress and r for slenderness when a section is not in a published table.

  • Fabricated and built-up sections

    Work out properties of plate girders, welded tees and box sections cut from plate.

  • Timber and aluminium extrusions

    Find the stiffness of joists, posts and simple extrusion profiles from their dimensions.

  • Coursework

    Check centroid and parallel-axis calculations for mechanics of materials problems.

Tips and limitations

  • For a Class 1 or 2 cross-section, bending resistance Mc,Rd uses Wpl; for Class 3, Wel,min (SteelConstruction.info, Member design). Take the class from the c/tf and c/tw ratios in the Blue Book rather than from this tool, which does not model the root radius used in c.
  • Use the tabulated Blue Book values in design calculations; use this tool for plated, notched or cut sections and to sense-check a look-up.
  • Iy in cm⁴ times 10,000 gives mm⁴, the unit most UK hand calculations and software inputs use.
  • Steel for Life lists both S275 and S355 resistance tables; the section properties themselves do not depend on the grade.

Sources and further reading

  1. Universal beams (UB): dimensions and properties, Eurocode 3 UK NA, Steel for Life and SCI (Blue Book). Rows for 305 x 165 x 40 and 457 x 191 x 67 UB used in the comparisons.
  2. Parallel flange channels (PFC): dimensions and properties, Eurocode 3 UK NA, Steel for Life and SCI (Blue Book). Row for 200 x 90 x 30 PFC.
  3. Member design, SteelConstruction.info (SCI). Section classes 1 to 4; Mc,Rd uses Wpl for Class 1 and 2 cross-sections and Wel,min for Class 3.

Frequently asked questions

What is the second moment of area of a 305 x 165 x 40 UB?

The Blue Book lists Iy = 8,500 cm⁴ about the major axis and Iz = 764 cm⁴ about the minor axis. From the plate dimensions alone this tool gives 8,370 cm⁴ and 764.2 cm⁴.

Why is the calculator lower than the Blue Book?

Rolled UK sections have a root radius where the web meets each flange (8.9 mm on a 305 x 165 x 40). The extra steel adds about 1.5% to the area and major-axis properties. The tool treats the section as three flat plates.

What are Wel and Wpl in Eurocode 3?

Wel is the elastic section modulus (the tool's S) and Wpl is the plastic section modulus (the tool's Z). Bending resistance of Class 1 and 2 cross-sections is based on Wpl, Class 3 on Wel.

Which axis is y-y on a UK beam?

In Eurocode notation y-y is the major (strong) axis and z-z the minor axis. The tool labels them x-x and y-y, so read its Ix as Iy and its Iy as Iz.

Can I use this for a section that is not in the Blue Book?

Yes. Plated girders, tees cut from UBs at a non-standard depth, or a channel with a notched flange are where a dimension-based calculator earns its place. Check the result against a standard section of similar size.

Is there an in-depth guide to the Section Properties Calculator?

Yes. “Moment of Inertia, Section Modulus and Radius of Gyration for Engineers” covers the background, how it works, common pitfalls and worked examples. Read the full guide.