United Kingdom version. Uses 25 kg cement bags and UK site mixes such as 1:2:4 and 1:5 all-in ballast, with BS 8500 designated mixes and HSE advice on wet cement. US version

Concrete Mix Ratio Calculator (UK)

How many 25 kg bags of cement, and how much sand, gravel or all-in ballast, for a shed base, patio or footing mixed at 1:2:4, 1:2:3 or 1:5 ballast.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Concrete Mix Ratio Calculator?

When you mix by hand or in a hired mixer in the UK, the recipe is by volume: so many shovels of sand and gravel, or of all-in ballast, to one of cement. Cement is sold in 25 kg bags, and sand and ballast in bulk bags. This version starts with 25 kg bags and works out the bags, the sand and the coarse aggregate for the concrete you need, using the 1.54 dry volume factor to allow for the voids in loose materials.

For all-in ballast, which is sand and gravel already mixed, enter a custom ratio of 1 cement to 5 ballast in the sand box and 0 for aggregate. Ready-mixed concrete is ordered differently: suppliers sell BS 8500 designated mixes, such as GEN1 for unreinforced domestic foundations and PAV1 for house driveways and external paving, and standardised prescribed mixes such as ST3 and ST4, which Heidelberg Materials lists for shed and workshop bases. These are specified by strength and cement content rather than by a ratio, so treat the ratios here as a site approximation, not a match for a designation.

  • Nominal mixes from 1:1:2 to 1:5:10 plus a custom ratio
  • Editable dry volume factor, densities, bag size and water-cement ratio
  • Cement bags, sand and aggregate by volume and mass, water in litres and gallons
  • Per cubic metre or cubic yard table for every common mix and IS 456 Table 9
  • Metric and US units with conversion of your inputs
Read the guide: Concrete Mix Ratios and the 1.54 Dry Volume Factor Explained

Updated

How to use the Concrete Mix Ratio Calculator

  1. Choose metric or imperial, then enter the slab length, width and thickness, or switch to a known volume.
  2. Add a small allowance for waste and spillage, usually 2 to 5% for site batching.
  3. Pick a nominal mix or choose Custom and type the cement, sand and aggregate parts.
  4. Check the dry volume factor (1.54), water-cement ratio, bag size and the bulk densities of your sand and stone.
  5. Read the cement bags, sand, aggregate and water, then copy the list for your order.

Worked examples

Shed base, 2.4 x 1.8 m at 100 mm, 1:2:4

Input

2.4 x 1.8 m x 100 mm, 5% extra, 1:2:4, 25 kg bags, w/c 0.5

Output

0.454 m³ of concrete; 6 bags of cement (143.7 kg), 0.2 m³ of sand and 0.4 m³ of gravel; about 72 L of water

At 1:2:4 each cubic metre needs about 12.7 bags of 25 kg. A base this size is a long day of hand mixing; a hired mixer halves the effort.

Patio base, 3 x 3 m at 100 mm, 1:5 all-in ballast

Input

3 x 3 m x 100 mm, 5% extra, custom 1 : 5 : 0, 25 kg bags

Output

0.945 m³; 14 bags of cement (349 kg) and 1.21 m³ of ballast

The ballast weight shown (1.94 t) uses the default 1,600 kg/m³; damp ballast is heavier, so check the bulk bag weight before ordering. Bulk bag weights vary by merchant, so divide by the weight they quote.

Background and insight

Loose sand and stone contain a lot of air. When they are mixed with cement paste, the fine particles fill the voids between the coarse ones, so a cubic metre of finished concrete needs roughly 1.5 to 1.6 cubic metres of dry, loose ingredients. Indian and many South Asian textbooks use 1.54 (some 1.52 or 1.57); the figure also covers bulking of damp sand and a little handling loss. Cement volume is then dry volume x c / (c + s + a), and its mass follows from a bulk density of 1,440 kg/m³, which makes a 50 kg bag 0.0347 m³.

IS 456:2000 clause 9.3 permits nominal mix concrete only up to M20 and states it by mass in Table 9: per 50 kg bag of cement, 800 kg of total aggregate for M5, 625 for M7.5, 480 for M10, 330 for M15 and 250 for M20, with fine to coarse generally 1:2 and a cap on water. The traditional volume ratios 1:5:10, 1:4:8, 1:3:6, 1:2:4 and 1:1.5:3 are their site equivalents. In US practice, ACI 211.1 proportions mixes by absolute volume from trial batches instead, and a sack of portland cement is 94 lb, taken as one loose cubic foot.

Common use cases

  • Site-batched slabs and footings

    Plan cement bags and truckloads of sand and stone for a mixer pour where ready-mix is not available.

  • Student and exam problems

    Check textbook answers for cement bags per cubic metre of M10, M15 or M20 nominal mix.

  • Comparing mixes

    See how much more cement a 1:1.5:3 mix needs than 1:2:4 before choosing one for a job.

  • Small repairs

    Scale a ratio down to a few wheelbarrows for steps, plinths and fence footings.

Tips and limitations

  • Wet cement is strongly alkaline. HSE guidance says it can cause burns if trapped against the skin, so wear waterproof gloves and boots high enough to keep it out, and wash it off straight away.
  • Add water gradually: too much water weakens the concrete more than a slightly stiff mix.
  • For anything structural, or a slab over 1 m³, a ready-mix or volumetric supplier will deliver a designated mix that you can specify by name.
  • Concreting more than 5 m² of a front garden in England needs planning permission unless the water drains to a lawn or border.

Sources and further reading

  1. Construction hazardous substances: Cement, Health and Safety Executive. Burns and dermatitis from wet cement and the controls to use.
  2. Types of concrete, Heidelberg Materials UK. Applications of the GEN1, PAV1, ST3 and ST4 mixes.
  3. Permeable surfacing of front gardens: guidance, GOV.UK. When concrete over a front garden needs planning permission in England.

Frequently asked questions

What is the mix ratio for concrete in the UK?

For general work like footings, shed bases and paths, 1 part cement to 2 parts sharp sand to 4 parts gravel (1:2:4), or 1 cement to 5 all-in ballast, are the usual site mixes. A richer 1:2:3 gives more cement per cubic metre for work that needs to be stronger. These are volume ratios measured with the same bucket or shovel.

How many 25 kg bags of cement per cubic metre of concrete?

About 12.7 bags for 1:2:4 and 14.8 bags for 1:2:3, using the 1.54 dry volume factor and cement at 1,440 kg/m³. Round up and keep a spare bag, since bags opened in damp weather go off.

What is all-in ballast?

A mix of sharp sand and gravel sold ready-combined for concrete. Because the sand and gravel are already blended, you only measure cement and ballast, commonly 1 to 5 for general concrete and leaner for blinding. Enter it as a custom ratio with 0 for aggregate.

What is GEN1 or PAV1 concrete and what ratio is it?

They are designated concretes from BS 8500 that ready-mix suppliers make to a set strength class and minimum cement content. Heidelberg Materials lists GEN1 for unreinforced domestic foundations, kerbing and haunching, and PAV1 for house driveways, external paving and patios; for shed bases it lists the standardised prescribed mixes ST3 and ST4. None of them is defined as a volume ratio, so there is no exact hand-mix equivalent.

How much water do I add to a bag of cement?

At a water to cement ratio of 0.5, a 25 kg bag needs about 12.5 litres in total, including the water already in damp sand. Start with less and add it slowly until the mix is workable.

Is there an in-depth guide to the Concrete Mix Ratio Calculator?

Yes. “Concrete Mix Ratios and the 1.54 Dry Volume Factor Explained” covers the background, how it works, common pitfalls and worked examples. Read the full guide.