India version. Uses 50 kg cement bags and IS 456 nominal mixes (M20 1:1.5:3, M15 1:2:4, M10 1:3:6) with the 1.54 dry volume factor and the Table 9 water limits. US version

Concrete Mix Calculator (M20, M15, M10)

Cement bags, sand and aggregate for M20 (1:1.5:3), M15 (1:2:4) or M10 nominal mix by volume, in 50 kg bags and m³, checked against IS 456 Table 9.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Concrete Mix Ratio Calculator?

Most small buildings in India are still batched on site by volume: one bag of cement with a measured number of ghamelas or boxes of sand and coarse aggregate. IS 456 allows these nominal mixes only up to M20; M25 and above must be design mixes. The traditional volume ratios are 1:1.5:3 for M20, 1:2:4 for M15 and 1:3:6 for M10, and this version uses them with 50 kg bags.

The 1.54 factor turns the wet concrete volume into the loose dry volume of cement, sand and aggregate, because the dry materials have voids and lose volume when mixed. From that the tool gives the cement bags, the sand and 20 mm aggregate in cubic metres and kilograms, and the water at your water-cement ratio. IS 456 Table 9 caps water at 30 litres per 50 kg bag for M20 and 32 litres for M15.

  • Nominal mixes from 1:1:2 to 1:5:10 plus a custom ratio
  • Editable dry volume factor, densities, bag size and water-cement ratio
  • Cement bags, sand and aggregate by volume and mass, water in litres and gallons
  • Per cubic metre or cubic yard table for every common mix and IS 456 Table 9
  • Metric and US units with conversion of your inputs
Read the guide: Concrete Mix Ratios and the 1.54 Dry Volume Factor Explained

Updated

How to use the Concrete Mix Ratio Calculator

  1. Choose metric or imperial, then enter the slab length, width and thickness, or switch to a known volume.
  2. Add a small allowance for waste and spillage, usually 2 to 5% for site batching.
  3. Pick a nominal mix or choose Custom and type the cement, sand and aggregate parts.
  4. Check the dry volume factor (1.54), water-cement ratio, bag size and the bulk densities of your sand and stone.
  5. Read the cement bags, sand, aggregate and water, then copy the list for your order.

Worked examples

M20 roof slab, 4.5 x 3.6 m, 150 mm thick

Input

4.5 x 3.6 m x 150 mm, 5% extra, 1:1.5:3, 50 kg bags, w/c 0.5

Output

2.552 m³ of concrete; 21 bags of cement (1,029 kg); 1.07 m³ of sand; 2.14 m³ of aggregate; 514 L of water

That is about 8.06 bags per cubic metre. In Table 9 terms the sand and aggregate here weigh about 240 kg per bag of cement, within the 250 kg limit for M20.

One cubic metre of M15 PCC under footings

Input

1 m³, 1:2:4, 50 kg bags, w/c 0.5

Output

6.34 bags (316.8 kg); 0.44 m³ of sand; 0.88 m³ of aggregate; 158 L of water

Table 9 allows 330 kg of total aggregate per 50 kg bag for M15; the volume mix gives about 319 kg, so it is on the safe side.

Background and insight

Loose sand and stone contain a lot of air. When they are mixed with cement paste, the fine particles fill the voids between the coarse ones, so a cubic metre of finished concrete needs roughly 1.5 to 1.6 cubic metres of dry, loose ingredients. Indian and many South Asian textbooks use 1.54 (some 1.52 or 1.57); the figure also covers bulking of damp sand and a little handling loss. Cement volume is then dry volume x c / (c + s + a), and its mass follows from a bulk density of 1,440 kg/m³, which makes a 50 kg bag 0.0347 m³.

IS 456:2000 clause 9.3 permits nominal mix concrete only up to M20 and states it by mass in Table 9: per 50 kg bag of cement, 800 kg of total aggregate for M5, 625 for M7.5, 480 for M10, 330 for M15 and 250 for M20, with fine to coarse generally 1:2 and a cap on water. The traditional volume ratios 1:5:10, 1:4:8, 1:3:6, 1:2:4 and 1:1.5:3 are their site equivalents. In US practice, ACI 211.1 proportions mixes by absolute volume from trial batches instead, and a sack of portland cement is 94 lb, taken as one loose cubic foot.

Common use cases

  • Site-batched slabs and footings

    Plan cement bags and truckloads of sand and stone for a mixer pour where ready-mix is not available.

  • Student and exam problems

    Check textbook answers for cement bags per cubic metre of M10, M15 or M20 nominal mix.

  • Comparing mixes

    See how much more cement a 1:1.5:3 mix needs than 1:2:4 before choosing one for a job.

  • Small repairs

    Scale a ratio down to a few wheelbarrows for steps, plinths and fence footings.

Tips and limitations

  • Damp sand bulks, so a box of it holds less sand; IS 456 (10.2.4) allows volume batching only with an allowance for bulking and asks for weigh-batching where practical.
  • Keep cement bags off the floor and away from damp walls, and use the oldest stock first.
  • Keep the concrete wet for at least 7 days with OPC and at least 10 days with PPC or other blended cements (IS 456, 13.5.1).

Sources and further reading

  1. Handout on Indian Standards on Building Materials, Bureau of Indian Standards. Indian Standards for cement, aggregates, concrete and their tests.
  2. IS 456:2000 Plain and Reinforced Concrete: Code of Practice, Bureau of Indian Standards (copy at Public.Resource.Org). Clause 9.3 and Table 9, proportions for nominal mix concrete.

Frequently asked questions

How many bags of cement are required for 1 cubic metre of M20 concrete?

About 8.06 bags of 50 kg (403 kg) for a 1:1.5:3 volume mix, using the 1.54 dry volume factor and cement at 1,440 kg/m³. Round up to 8 or 9 bags and keep a spare for wastage.

What is the ratio of M15, M20 and M25 concrete?

The traditional nominal ratios are 1:2:4 for M15 and 1:1.5:3 for M20. IS 456 allows nominal mixes only up to M20 (clause 9.3), so M25 and above should be a design mix to IS 10262, even though 1:1:2 is often quoted for M25.

How much sand and aggregate for one bag of cement in M20?

At 1:1.5:3 one 50 kg bag (about 0.035 m³) goes with about 0.052 m³ of sand and 0.104 m³ of aggregate, which is roughly 1.5 and 3 times the bag volume.

How much water is needed for one bag of cement?

Water = water-cement ratio x 50 kg. At 0.5 that is 25 litres per bag. IS 456 Table 9 sets the maximum at 30 litres per bag for M20, 32 litres for M15 and 34 litres for M10, including the water already in wet sand.

Why multiply by 1.54 in concrete calculation?

Loose cement, sand and aggregate have air voids, and part of their volume is lost when they are mixed and compacted. Multiplying the wet volume by 1.52 to 1.57, commonly 1.54, gives the dry volume to batch.

Can I use nominal mix for an RCC slab?

IS 456 permits nominal mix up to M20, which covers many house slabs. The structural engineer decides the grade, and a design mix is required for M25 and above.

Is there an in-depth guide to the Concrete Mix Ratio Calculator?

Yes. “Concrete Mix Ratios and the 1.54 Dry Volume Factor Explained” covers the background, how it works, common pitfalls and worked examples. Read the full guide.