India version. Uses IS 1077 brick sizes (230 x 110 x 70 mm traditional, 190 x 90 x 90 mm modular), 10 mm joints, 50 kg cement bags and 1:6 or 1:4 cement mortar. US version
Brick Calculator for 9 Inch and 4.5 Inch Walls
Number of bricks, cement bags and sand for a 9-inch (230 mm) or 4.5-inch wall in Indian traditional or modular bricks with 1:6 or 1:4 cement mortar.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Brick and Block Calculator?
Indian brickwork is usually a 9-inch (230 mm) wall of traditional burnt clay bricks, 230 x 110 x 70 mm, for external walls, and a 4.5-inch (115 mm) wall for partitions, laid in 1:6 cement mortar for full-brick walls and 1:4 for half-brick walls. Modular bricks of 190 x 90 x 90 mm (IS 1077) make a 200 mm module with 10 mm joints, so they count neatly at 50 per square metre per leaf.
In this tool a one-leaf wall is the 4.5-inch wall and a two-leaf wall with the middle joint filled is the 9-inch wall. Enter the wall size and the doors and windows, and it gives the bricks to buy with wastage, the wet mortar, the 50 kg cement bags and the sand. Divide by the wall volume if you estimate per cubic metre of brickwork.
- US modular and standard brick, CMU 6, 8 and 12 in, UK brick and block, Indian modular and traditional brick
- Door and window openings, single or double wythe and collar joint
- Mortar by joint geometry with face-shell bedding for hollow block
- Cement bags and sand for any 1:n mortar, with 70 lb, 94 lb, 50 kg or 25 kg bags
- Waste allowances from BIA Technical Note 10 and cost per unit
Updated
How to use the Brick and Block Calculator
- Choose imperial or metric and enter the wall length and height.
- Enter the number and size of doors and windows to subtract from the wall area.
- Pick a brick or block size, or choose Custom and type the actual dimensions and joint thickness.
- Select single or double wythe, and whether the collar joint is filled with mortar.
- Set the waste allowances, the mortar mix and the cement bag, then read the units, mortar, cement and sand.
Worked examples
9-inch wall, 10 m long and 3 m high, traditional brick
Input
Indian traditional brick, two leaves, joint filled, 10 x 3 m, no openings, 5% waste, 15% mortar waste, 1:6 mortar
Output
3,282 bricks (3,125 net); 1.57 m³ of mortar; 9 bags of cement; 1.79 m³ of sand
The wall is 230 mm thick, so it holds 6.9 m³ of brickwork: about 453 bricks and 0.2 m³ of mortar per cubic metre before wastage.
4.5-inch partition with a door and a window
Input
Indian traditional brick, one leaf, 4 x 3 m less 3.36 m² of openings, 5% waste, 15% mortar waste, 1:4 mortar
Output
473 bricks; 0.18 m³ of mortar; 2 bags of cement; 0.19 m³ of sand
Half-brick walls use a richer 1:4 mortar. Openings are subtracted before wastage; lintels and the RCC band are counted separately.
Modular brick wall, 190 mm, per square metre
Input
Indian modular brick 190 x 90 x 90 mm, two leaves, 1 m², no waste
Output
100 bricks per m² of 190 mm wall
Each modular brick with its joint takes 200 x 100 mm of face, so one leaf is 50 per m² and a full-brick wall is 100.
Background and insight
Units per area = 1 / ((length + joint) x (height + joint)). The figures match Table 4 of BIA Technical Note 10: 675 modular brick and 5.5 cubic feet of mortar per 100 square feet at 3/8 in joints, or 8.1 cubic feet per 1,000 brick, and the collar joint adds 3.13 cubic feet per 100 square feet. Those table values exclude waste. BIA suggests adding at least 5% to brick and 15 to 25% to mortar, and it describes the mason's rule of eight bags of masonry cement per 1,000 brick as a very rough estimate.
Concrete masonry units are named by nominal size: an 8x8x16 block is actually 7-5/8 x 7-5/8 x 15-5/8 in, so with a 3/8 in joint it occupies exactly 8 x 16 in and 1.125 blocks fill a square foot. Hollow units are normally laid with face-shell bedding under TMS 602, which uses far less mortar than a full bed, but grouted cells and bond beams need grout that this calculator does not count. In India, IS 1077 sets the modular brick at 190 x 90 x 90 mm, which with 10 mm joints gives exactly 50 per square metre of half-brick wall.
Common use cases
Garden walls and planters
Order pallets of brick or block and enough mortar for a weekend build.
House extensions and veneers
Estimate brick veneer around windows and doors before asking for supplier quotes.
Comparing brick and block
See how many units and how much mortar the same wall needs in modular brick against CMU.
Indian and UK site estimates
Use local brick sizes and 1:4 or 1:6 cement mortar with 50 kg or 25 kg bags.
Tips and limitations
- Soak burnt clay bricks in water before laying so they do not suck the water out of the mortar.
- Bricks vary in size between kilns; measure ten from your load and use the custom size if they differ from 230 x 110 x 70 mm.
- Cure brickwork by keeping it wet for at least seven days.
Sources and further reading
- Handout on Indian Standards on Building Materials, Bureau of Indian Standards. IS 1077 common burnt clay building bricks and the related test standards.
- IS 1077:1992 Common Burnt Clay Building Bricks: Specification, Bureau of Indian Standards (copy at Public.Resource.Org). Modular and non-modular brick sizes and strength classes.
Frequently asked questions
How many bricks are in 1 cubic metre of brickwork?
About 453 traditional 230 x 110 x 70 mm bricks per cubic metre of 9-inch wall with 10 mm joints, before wastage, and about 500 modular bricks (190 x 90 x 90 mm) per cubic metre. Add 5% for breakage and cutting.
How many bricks for a 9-inch wall per square foot?
With traditional bricks and 10 mm joints a 9-inch wall takes about 104 bricks per square metre, which is roughly 9.7 bricks per square foot before wastage.
How much cement is needed for 1,000 bricks?
For a 9-inch wall in 1:6 mortar the example above uses about 8.6 bags for 3,125 bricks, so about 2.75 bags per 1,000 bricks including 15% mortar wastage. A half-brick wall in 1:4 uses more cement per brick.
What is the size of a standard brick in India?
IS 1077 gives the modular size as 190 x 90 x 90 mm (and 190 x 90 x 40 mm) and the non-modular traditional size as 230 x 110 x 70 mm (and 230 x 110 x 30 mm). Bricks are graded by compressive strength into classes such as 3.5, 5, 7.5 and 10 N/mm².
Which mortar ratio is used for brickwork?
1:6 cement to sand for 9-inch walls and 1:4 for 4.5-inch walls are the common site ratios. The structural engineer or the specification may call for a different mix.
Is there an in-depth guide to the Brick and Block Calculator?
Yes. “How Many Bricks and How Much Mortar? Estimating Masonry Walls” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.