India version. Adds the IS 800:2007 clause 7.1.2.1 design compressive strength, with the Table 10 buckling class, E250 steel to IS 2062 and checks that match IS 800 Table 9. US version
Column Buckling Calculator (IS 800)
Euler load and the IS 800 design compressive stress fcd with buckling classes a to d, γm0 = 1.10 and the KL/r limit of 180, for SHS, tubes, rods and ISMB.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Column Buckling Calculator?
An Indian steel strut or column is designed to IS 800:2007 clause 7.1.2. Its design compressive stress is fcd = χ fy / γm0, where χ comes from the non-dimensional slenderness λ = √(fy / fcc), the imperfection factor α of the buckling class (a 0.21, b 0.34, c 0.49, d 0.76) and γm0 = 1.10. This version sets the design-code check to IS 800 and shows λ, χ, fcd and the design load Pd for the section you enter.
The buckling class comes from Table 10. Hot-rolled hollow sections are class a and cold-formed hollow sections class b, while channels, angles, tees and solid sections are class c. For a 100 x 100 x 4 SHS in E250 steel (fy 250 MPa, IS 2062), pinned at both ends over 3 m, that difference is 240 kN cold-formed against 265 kN hot-rolled.
The results agree with the tabulated values in IS 800 Table 9: with fy = 250 MPa and class c, the calculator gives fcd = 183 MPa at KL/r 50 and 107 MPa at KL/r 100, the same as Table 9(c). Table 3 caps KL/r at 180 for members carrying dead and imposed loads, and the result panel warns when you go past it.
- Euler critical load and stress with effective length KL and slenderness KL/r
- Six end conditions with theoretical and AISC recommended K values, or a custom K
- Johnson parabola below the transition slenderness, with a clear validity warning
- AISC 360-16 E3 cross-check with LRFD φPn and ASD Pn/Ω, or a design-code check to BS EN 1993-1-1 (UK NA), IS 800 or CSA S16
- Tube, bar, SHS and rectangle sections or your own I and A, SI and US units, column curve chart
Updated
How to use the Column Buckling Calculator
- Choose SI or US units, then pick the end conditions. The list shows the theoretical K and the AISC recommended design K for each.
- Select whether to use the design value, the theoretical value or a custom K, and enter the unbraced length L between lateral supports.
- Pick a material to fill in E and the yield strength, or type your own. Leave Fy blank for a pure Euler result.
- Describe the cross-section. For an I-beam or channel, enter the weak-axis I and the area from a section table, because the column buckles about the axis with the smallest I.
- Read the Euler load, slenderness, governing formula and allowable load, and check the AISC E3 values and the column curve.
Worked examples
100 x 100 x 4 SHS, E250, 3 m, pinned
Input
SHS 100 x 4 mm, K = 1.0, E 200 GPa, fy 250 MPa, IS 800, cold-formed
Output
KL/r 76.5; λ 0.861; class b, χ 0.686; fcd 156 MPa; Pd 240 kN
As a hot-rolled section (class a) χ is 0.759 and Pd 265 kN. Euler alone gives 518 kN, more than twice the design value.
88.9 x 4.0 tube, 2.5 m, pinned
Input
Round tube 88.9 x 4 mm, K = 1.0, E 200 GPa, fy 250 MPa, IS 800
Output
KL/r 83.2; cold-formed fcd 145 MPa, Pd 155 kN; hot-rolled Pd 172 kN
A common size for trusses and light columns. With fy 310 MPa the cold-formed tube carries 172 kN, the same as the hot-rolled E250 one.
Background and insight
Leonhard Euler derived the critical load of an ideal pin-ended column in 1744: Pcr = π²EI/L². Other end conditions are handled by replacing L with an effective length KL, the distance between points of zero moment in the buckled shape. A column fixed at both ends buckles like a pinned column half as long (K = 0.5), a flagpole fixed at the base and free at the top like one twice as long (K = 2.0). Since the load varies with 1/K², end fixity changes capacity by a factor of up to sixteen.
Euler assumes the material stays elastic, so it is only valid when the critical stress Pcr/A is below the proportional limit. Real rolled and welded sections carry residual stresses from cooling, so yielding starts earlier; the classic structural stability texts (and the old AISC allowable stress method) put the limit at half the yield stress. Below the transition slenderness Cc = √(2π²E/Fy), J. B. Johnson's parabola, σcr = Fy − (Fy²/4π²E)(KL/r)², joins the Euler curve tangentially at Fy/2 and caps the stress at Fy for a stub column.
Modern steel codes use a single curve fitted to tests on columns with real out-of-straightness. AISC 360-16 Section E3 gives Fcr = 0.658^(Fy/Fe) Fy for KL/r up to 4.71√(E/Fy) and 0.877 Fe beyond, where Fe is the Euler stress, with φ = 0.90 for LRFD and Ω = 1.67 for ASD. The recommended K values (0.65, 0.80, 1.2, 1.0, 2.1 and 2.0) come from Commentary Table C-A-7.1.
Common use cases
Posts and pipe columns
Check a steel post, lally column or tube upright under a beam before choosing its size.
Struts, braces and push rods
Find the buckling load of a compression strut, linkage, actuator rod or truss member.
Machine and frame design
Size aluminium or steel frame legs and slender machine parts against elastic buckling.
Teaching stability
Show how K, length and section shape move a column along the Euler and Johnson curves.
Tips and limitations
- Effective length factors in IS 800 Table 11 are close to the design values in the list: 0.65L for both ends fixed, 0.8L for one fixed and one hinged, 1.0L for both hinged, 2.0L for a free top.
- For an ISMB column, choose "Enter I and A directly" with Iyy and the area from IS 808, and set the section type to rolled I (h/b over 1.2) so the minor axis uses class b.
- Check the cross-section class first: slender (class 4) walls need an effective area, which this calculator does not compute.
Sources and further reading
- IS 800:2007 General construction in steel, code of practice, Bureau of Indian Standards (public copy). Clause 7.1.2.1, Table 7 imperfection factors, Table 9 fcd values, Table 10 buckling classes, Table 3 slenderness limits.
- Handout on building materials, Bureau of Indian Standards. IS 2062 hot rolled medium and high tensile structural steel.
- Lok Sabha unstarred question 3149: Quality control orders for steel products (6 August 2018), Ministry of Steel, Government of India. IS 2062 structural steel is among the products that must carry the BIS mark.
Frequently asked questions
How is design compressive stress fcd calculated in IS 800?
fcd = (fy / γm0) / (φ + √(φ² − λ²)), with φ = 0.5 [1 + α (λ − 0.2) + λ²], λ = √(fy / fcc) and fcc = π²E / (KL/r)². The design load is Pd = Ae × fcd.
Which buckling class applies to hollow sections in IS 800?
Table 10 puts hot-rolled hollow sections in class a and cold-formed ones in class b, about any axis. Eurocode 3 puts cold-formed sections on curve c, so the Indian code is a little more generous for these.
What is the value of γm0 in IS 800?
γm0 = 1.10 for resistance governed by yielding, which includes the buckling resistance of compression members.
What is the maximum slenderness ratio for a column?
IS 800 Table 3 limits KL/r to 180 for a member carrying compressive loads from dead and imposed loads. Members loaded in compression only by wind or earthquake combinations may go to 250.
Can I check my answer against IS 800 Table 9?
Yes. Enter a section and length that give a round KL/r, set fy to 250 MPa and the class you need. At KL/r 100 and class c the calculator shows 107 MPa, as Table 9(c) does.
Is there an in-depth guide to the Column Buckling Calculator?
Yes. “Column Buckling Explained: Euler, K Factors, Slenderness and the Johnson Parabola” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.