India version. Uses IS 808 section dimensions and IS 800:2007 notation (Ze, Zp), and shows where the plate model departs from IS 808 for tapered-flange ISMB and ISMC sections. US version
Section Properties of ISMB, ISMC and Plates
Moment of inertia, elastic modulus Ze and plastic modulus Zp for ISMB, ISMC and built-up sections in mm, checked against IS 808 tables, in IS 800 notation.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Section Properties Calculator?
Indian steel design works from IS 808 section tables and IS 800:2007, so this version starts from an ISMB 300 and compares the calculator with the tabulated values. Enter D, B, t and T from IS 808 Table 2.1 (beams) or Table 4.1 (channels) in millimetres. The tabulated values quoted on this page are from IS 808:1989; check the current BIS edition before design.
Notation trips up many students. IS 808 lists the elastic section modulus as Zx in cm³. IS 800:2007 calls the elastic modulus Ze and the plastic modulus Zp, and clause 8.2.1.2 gives the design bending strength as Md = βb Zp fy / γm0. In this tool the elastic modulus is S (use it as Ze) and the plastic modulus is Z (use it as Zp).
ISMB and ISMC sections have sloping flanges (98° and 96° in IS 808) and root radii. The calculator treats each flange as a flat plate of the mean thickness T. That keeps area and major-axis values within about 2%, but it overstates the minor axis by 13 to 23%, as the examples show. Use IS 808 values for ry and weak-axis checks.
- Eight shapes: rectangle, hollow rectangle, circle, tube, I-beam, T, channel and angle
- Area, centroid, Ix, Iy, Sx and Sy at each fibre, Zx, Zy, rx and ry
- Product of inertia, principal moments and minimum r for angles; polar moment J for circles and tubes
- Scaled cross-section drawing with centroid and axes
- Results in two units side by side, copy summary and share link
Updated
How to use the Section Properties Calculator
- Pick the shape and the unit you want to work in.
- Enter the dimensions shown for that shape. Flange widths, depths and thicknesses are outside dimensions; for tubes enter the outside diameter or size and the wall thickness.
- Check the drawing: the red dashed line is the x-x centroidal axis and the green one is y-y.
- Read the headline area, Ix, minimum Sx and Zx, then the full table with both units.
- For angles, use the principal values and the minimum radius of gyration for buckling checks. Copy the table or share the link.
Worked examples
ISMB 300
Input
I-beam: B = 140, D = 300, T = 13.1, t = 7.7 mm
Output
A = 57.76 cm²; Ixx = 8,870 cm⁴; Ze = 591.4 cm³; Zp = 670.5 cm³; Iyy = 600.1 cm⁴; ry = 3.22 cm
IS 808 Table 2.1 lists A = 58.6 cm², Ix = 8,990 cm⁴, Zx = 599 cm³, Iy = 486 cm⁴ and ry = 2.86 cm. Major-axis values are about 1.3% low; Iyy is 23% high because tapered flanges are thinner at the tips than the plate model assumes.
ISMB 200
Input
I-beam: B = 100, D = 200, T = 10.0, t = 5.7 mm
Output
A = 30.26 cm²; Ixx = 2,084 cm⁴; Ze = 208.4 cm³; Zp = 236.2 cm³; Iyy = 166.9 cm⁴
IS 808: A = 30.8 cm², Ix = 2,120 cm⁴, Zx = 212 cm³, Iy = 137 cm⁴. The pattern repeats: close on the major axis, 22% high on the minor axis.
ISMC 200
Input
Channel: B = 75, D = 200, T = 11.4, t = 6.2 mm
Output
A = 28.09 cm²; Ixx = 1,810 cm⁴; Ze = 181.0 cm³; Iyy = 159.7 cm⁴; centroid 24.0 mm from the web back
IS 808 Table 4.1: A = 28.5 cm², Ix = 1,830 cm⁴, Zx = 181 cm³, Iy = 141 cm⁴, Cy = 22.0 mm. Ze matches; the minor axis is 13% high and the centroid sits 2 mm further out.
Background and insight
The calculator splits each shape into rectangles, finds the centroid from the first moment of area, ȳ = ΣAy/ΣA, and then applies the parallel axis theorem, I = Σ(bh³/12 + A d²), to move each piece's own inertia to the common centroidal axis. Hollow shapes subtract the hole. Circles use the exact π D⁴/64. The product of inertia Ixy is computed the same way, and for angles Mohr's circle gives the principal values and the rotation of the principal axes.
The elastic section modulus S = I/c, with c the distance from the centroid to the extreme fibre, converts a bending moment into the maximum elastic stress, σ = M/S. The plastic modulus Z is the first moment of area about the plastic neutral axis, which divides the area into two equal halves; M = Fy Z is the moment at which the whole section has yielded. The ratio Z/S, the shape factor, is 1.5 for a rectangle, 1.70 for a solid circle and roughly 1.1 to 1.2 for I-beams bent about the strong axis. AISC calls these S and Z; Eurocode 3 calls them Wel and Wpl.
Rolled sections have root fillets between web and flange and rounded toes, which this tool ignores. The effect is small but real: an L4x4x1/2 angle calculated here has A = 3.75 in² and ȳ = 1.18 in, matching the AISC Manual, while Ix comes out at 5.56 in⁴ against the tabulated 5.52 in⁴, less than 1% apart.
Common use cases
Beam and column checks
Get I for deflection, S for bending stress and r for slenderness when a section is not in a published table.
Fabricated and built-up sections
Work out properties of plate girders, welded tees and box sections cut from plate.
Timber and aluminium extrusions
Find the stiffness of joists, posts and simple extrusion profiles from their dimensions.
Coursework
Check centroid and parallel-axis calculations for mechanics of materials problems.
Tips and limitations
- Check Zp/Ze against the clause 8.2.1.2 limit: to avoid irreversible deformation under service loads, Md must stay below 1.2 Ze fy/γm0 for simply supported beams. For ISMB 300 the tool gives Zp/Ze = 1.13, inside that limit.
- Use the calculator for built-up sections (ISMB with cover plates, plate girders, double channels) where IS 808 has no row, then sense-check against the nearest rolled section.
- IS 808 gives properties in cm⁴ and cm³; multiply cm⁴ by 10,000 for mm⁴, the unit most STAAD and hand calculations use.
- Section class (plastic, compact, semi-compact) comes from the width-to-thickness ratio limits in IS 800:2007 Table 2 (clause 3.7.2); read B, T, D and t from IS 808 for that check.
Sources and further reading
- IS 808:1989 Dimensions for hot rolled steel beam, column, channel and angle sections, Bureau of Indian Standards (via Public.Resource.Org). Table 2.1 (ISMB 200, ISMB 300) and Table 4.1 (ISMC 200) dimensions and properties.
- IS 800:2007 General construction in steel: code of practice, Bureau of Indian Standards (via Public.Resource.Org). Clause 8.2.1.2: Md = βb Zp fy/γm0, the 1.2 Ze fy/γm0 limit, and Ze and Zp definitions.
- Bureau of Indian Standards, Bureau of Indian Standards. Publisher of IS 808 and IS 800; buy current editions here.
Frequently asked questions
What is the moment of inertia of ISMB 300?
IS 808:1989 Table 2.1 gives Ix = 8,990 cm⁴ and Iy = 486 cm⁴. From its dimensions (300 x 140 mm, 7.7 mm web, 13.1 mm flange) this calculator gives 8,870 cm⁴ and 600.1 cm⁴, because it ignores the root radius and the flange slope.
What is the section modulus of ISMB 300?
The elastic section modulus in IS 808 is Zx = 599 cm³ (Ze in IS 800). The calculator gives Ze = 591.4 cm³ and the plastic modulus Zp = 670.5 cm³, which IS 808 does not tabulate.
What is the difference between Ze and Zp in IS 800?
Ze is the elastic section modulus and Zp the plastic section modulus. Clause 8.2.1.2 uses Zp for plastic and compact sections (βb = 1.0) and Ze through βb = Ze/Zp for semi-compact sections.
Why is the tool's Iyy higher than IS 808 for ISMB and ISMC?
Indian medium-weight beams and channels have sloping flanges, thick at the web and thin at the toes. A flat plate of the mean thickness puts more steel at the toes than the real section, which raises Iyy. Use the IS 808 value for minor-axis checks.
Where do I find ISMB and ISMC dimensions?
IS 808:1989 Section 2 (beams, Table 2.1 for medium-weight beams) and Section 4 (channels, Table 4.1). Designations follow clause 6.1, for example MB 200 for a 200 mm deep medium-weight beam.
Is there an in-depth guide to the Section Properties Calculator?
Yes. “Moment of Inertia, Section Modulus and Radius of Gyration for Engineers” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.