mm to Inches Converter

Convert millimeters to inches with the exact 1 in = 25.4 mm definition and worked examples from drawings, socket sets and 3D printer nozzles.

The interactive tool loads here when JavaScript runs.

About this tool

What is the mm to Inches Converter?

Millimeters and inches share every workshop. A drawing dimensions a bracket at 76.2 mm, the stock list sells 3 inch bar; a bolt head needs a 13 mm socket but the set on the shelf is SAE; a 3D printer extrudes through a 0.4 mm nozzle while the filament spec sheet talks thousandths of an inch. This converter settles each of those by dividing millimeters by exactly 25.4, the definition of the inch since 1959.

Because 25.4 is exact, the quality of a result depends only on how many decimals you keep, and in mechanical work the decimals are the whole game. A clearance of 0.1 mm is about four thousandths of an inch; round an inch value to two places and you have thrown away more than the tolerance. The steps panel shows the division at full precision so you decide where to cut it off, not the tool.

The division is performed by the page itself, offline-capable and with nothing posted to a server. Each result expands to show your millimeters over the exact 25.4 definition, and the report bar can hand the conversion onward as a CSV, a PDF or a link that reopens the converter with your dimension already typed.

  • Millimeter to inch conversion by the exact 25.4 mm definition
  • Full-precision results so tolerance work is not rounded away silently
  • Working steps that display the division with your dimension in it
  • Handles tiny values like nozzle bores and large ones like sheet sizes alike
  • Report bar with CSV, PDF and share link; the arithmetic never leaves your machine
Read the guide: Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets

Updated

How to use the mm to Inches Converter

  1. Type the millimeter dimension, with as many decimals as the drawing or caliper gives.
  2. Read the inch value, which is your number divided by exactly 25.4.
  3. Open the working steps to see the division spelled out against the 1959 definition.
  4. Keep more decimal places for tolerances and fits than you would for rough stock sizes.
  5. Send the figure on via the report bar, as a CSV or PDF or a link preloaded with your dimension.

Worked examples

The definition itself

Input

25.4 mm

Output

1 in

Dividing 25.4 by 25.4 returns exactly 1, with no remainder, because the inch is defined as 25.4 mm rather than measured against it. Any converter showing 0.99998 here is using a pre-1959 value.

A printer nozzle

Input

0.4 mm

Output

0.01575 in

0.4 / 25.4 = 0.015748 in, which a machinist would call 15.7 thou. Filament tolerances of plus or minus 0.05 mm are about 2 thou, tighter than they sound in millimeters.

Socket roulette

Input

13 mm

Output

0.5118 in

A 13 mm bolt head is 0.512 in across the flats, while a 1/2 in socket is 12.7 mm. The 0.3 mm gap is why the SAE socket sometimes grabs, rounds the corners, and ruins the bolt.

A fractional neighbour

Input

9.525 mm

Output

0.375 in = 3/8 in

9.525 / 25.4 = 0.375 exactly, the 3/8 in of bolt and drill charts. Hardware dimensions often convert to clean fractions because the parts were designed in inches to begin with.

Background and insight

The inch spent most of its history as a slightly different length in every country that used it. By the early twentieth century the US inch worked out to 25.40005 mm through its metric definition of the yard, while the British inch sat near 25.39998 mm. The Swedish gauge-block maker Carl Edvard Johansson split the difference decades before governments did, manufacturing his blocks to an even 25.4 mm from around 1912 so one set could serve customers in both systems; industry quietly adopted his value.

The 1959 international yard and pound agreement made the industrial practice official, defining the yard as 0.9144 m and the inch therefore as exactly 25.4 mm in the US, UK and Commonwealth. From then on millimeter and inch dimensions have been two notations for one length standard, and a converted value is exact rather than approximate.

Machinists rarely speak in decimal inches alone. US practice divides the inch into thousandths, called thou or mil, so 0.0254 mm is one thou, while fractional inches in 8ths, 16ths, 32nds and 64ths rule hardware sizes: a 3/8 in bolt is 9.525 mm, a 1/16 in drill is 1.5875 mm. Reading a millimeter dimension well often means knowing both the decimal value and the nearest fraction it is standing next to.

Common use cases

  • Reading dual-standard drawings

    Move between millimeter-dimensioned CAD exports and inch-based stock, taps and fasteners on the same job.

  • Choosing tools that fit

    Check whether a metric fastener can safely take the nearest SAE socket or wrench before reaching for it.

  • 3D printing and CNC setup

    Convert nozzle diameters, layer heights and offsets when firmware, slicer and documentation disagree on units.

  • Buying materials abroad

    Match sheet, rod and pipe sizes listed in inches against the millimeter dimensions a project was designed around.

Tips and limitations

  • A fast mental factor: 1 mm is about 40 thou, and 25 mm is about an inch, short by only 1.6 percent.
  • To find the nearest fractional inch, multiply the decimal result by the denominator you care about: 0.5118 in x 16 = 8.19, so 13 mm sits just past 8/16, which is 1/2 in.
  • Keep raw precision until the final figure. Converting each dimension on a drawing separately and rounding as you go stacks errors that a single conversion at the end avoids.
  • One thou is exactly 0.0254 mm, so tolerance tables translate cleanly: plus or minus 0.1 mm is about plus or minus 4 thou.
  • Watch for soft-converted specs: a part listed as 25 mm may really be a 1 in design, and the missing 0.4 mm matters when it must mate with true metric parts.

Sources and further reading

  1. NIST Special Publication 811: Guide for the Use of the International System of Units, National Institute of Standards and Technology. Appendix B carries the exact inch and mil factors
  2. Inch, Wikipedia. National inch values before 1959 and the 25.4 mm definition
  3. Carl Edvard Johansson, Wikipedia. The gauge blocks that used 25.4 mm decades before the agreement

Frequently asked questions

How many inches is 10 mm?

0.3937 in, from 10 / 25.4. It sits between 3/8 in (0.375) and 13/32 in (0.40625), which is why a 10 mm bolt head has no comfortable SAE socket.

Is a 13 mm socket the same as a half inch socket?

No, and the difference is 0.3 mm: 1/2 in is 12.7 mm while the bolt head is 13 mm. The SAE socket often fits loosely enough to slip under torque and round the flats, so use the metric size.

How do I turn a decimal inch result into a fraction?

Multiply the decimal part by the denominator you want, usually 16, 32 or 64, and round to the nearest whole numerator. For 20 mm, 0.7874 in x 32 = 25.2, so the nearest 32nd is 25/32, about 0.4 percent small.

What is a thou, and how many millimeters is it?

A thou, also called a mil, is one thousandth of an inch: exactly 0.0254 mm. US machining tolerances are quoted in thou, so a fit specified as 2 thou of clearance is 0.0508 mm.

How many millimeters is 3/8 of an inch?

Exactly 9.525 mm, since 0.375 x 25.4 = 9.525. Common fractions convert exactly because the inch itself is defined in millimeters; nothing about the fraction introduces rounding.

Why do some drawings mix millimeters and inches?

Because supply chains do. A product engineered in millimeters may still specify inch-standard fasteners, pipe threads or bearings, and legacy US designs get metric parts grafted on. Dual dimensioning acknowledges that both toolboxes will touch the part.

Is there an in-depth guide to the mm to Inches Converter?

Yes. “Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets” covers the background, how it works, common pitfalls and worked examples. Read the full guide.