Torque Unit Converter

Convert torque between newton meters, pound-feet, pound-inches, kilogram-force meters and ounce-inches using the exact 1.3558 N·m per lb-ft factor.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Torque Unit Converter?

Convert a torque figure once and read it in newton meters, newton centimeters, pound-feet, pound-inches, kilogram-force meters and ounce-inches simultaneously. Torque specs are where unit mix-ups cost real hardware: a European service manual says 110 N·m, your torque wrench is graduated in lb-ft, and the correct setting is 81.1 lb-ft, not 110. Set the wrench to 110 lb-ft instead and you apply 149 N·m, 36 percent over spec, enough to stretch a wheel stud.

The factors here are the exact defined values: 1 lbf·ft = 1.3558179483314004 N·m, derived from the standard pound-force (4.4482216152605 N) and the international foot (0.3048 m), and 1 kgf·m = 9.80665 N·m from the standard gravity definition. Pound-inches divide the lb-ft figure by 12, and ounce-inches divide the lb-in figure by 16.

The arithmetic runs locally in the page with nothing uploaded anywhere. Choose the unit your wrench reads to get working steps that name the exact factor used, then pull the whole table into CSV or PDF from the report bar, or copy a link that lands a workmate on the same filled-in conversion.

  • Six torque units converted together: N·m, N·cm, lbf·ft, lbf·in, kgf·m and ozf·in
  • Working steps that state the exact defined factor, such as 1 lbf·ft = 1.3558179483 N·m
  • Factors built from standard gravity and the international foot, not rounded shop values
  • Full conversion table export to CSV or PDF through the report bar
  • Runs in the browser only, with a shareable link to the exact conversion
Read the guide: Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets

Updated

How to use the Torque Unit Converter

  1. Type the torque figure from your service manual, fastener chart or datasheet.
  2. Pick the unit the spec is written in, for example N·m from a European manual.
  3. Read the same torque in all six units from the table.
  4. Select the unit on your wrench to see the conversion steps with the exact factor.
  5. Export the table as CSV or PDF, or copy the share link, before heading to the garage.

Worked examples

Lug nut spec to a lb-ft wrench

Input

110 N·m

Output

81.13 lbf·ft

110 ÷ 1.3558179483314004 = 81.13. A typical passenger-car wheel spec of 110 N·m sets a lb-ft wrench just above 81. Setting it to 110 lb-ft instead would deliver 149 N·m.

Metric bolt chart in three units

Input

25 N·m

Output

18.44 lbf·ft = 221.27 lbf·in = 2.549 kgf·m

The common M8 class 8.8 figure converts to 18.44 lb-ft (25 ÷ 1.3558179) or 221.27 lb-in (12 times more). The kgf·m value, 25 ÷ 9.80665 = 2.549, matches what an older Japanese manual would print.

US spec to newton meters

Input

100 lbf·ft

Output

135.58 N·m

100 × 1.3558179483314004 = 135.58 N·m. Cylinder-head and suspension torques in US manuals land in this range, and a metric wrench needs the converted figure, not the printed one.

Vintage manual in kgf·m

Input

10 kgf·m

Output

98.07 N·m = 72.33 lbf·ft

10 × 9.80665 = 98.0665 N·m exactly, since the kilogram-force is defined through standard gravity. Dividing by 1.3558179 gives 72.33 lb-ft for an imperial wrench.

Background and insight

Torque is force times lever arm, so each unit pairs a force with a length. The newton meter is coherent SI. The pound-foot (written lb-ft or ft-lb interchangeably in shop manuals, both meaning pound-force times foot) dominates American automotive and aviation practice. The kilogram-force meter predates SI and lingers in older Japanese and European manuals: a 1980s motorcycle spec of 3.5 kgf·m is 34.3 N·m.

The lb-ft and N·m scales sit close enough to be dangerous. The ratio is only 1.356, so a misread spec gives a plausible-feeling result either way, unlike confusing inches with millimeters. Fastener charts make the stakes concrete: an M8 class 8.8 bolt typically tightens to about 25 N·m, which is 18.4 lb-ft; apply 25 lb-ft (33.9 N·m) and you are 36 percent over, into yield territory for many joints.

Pound-inches exist because small fasteners need resolution. Electronics, firearms and aircraft interior work specify screws in lb-in or even oz-in, where a lb-ft wrench cannot be read accurately: 30 lb-in is only 2.5 lb-ft. Dimensionally a newton meter equals a joule, but torque is conventionally never written in joules, because the force here acts perpendicular to the lever rather than along a displacement.

Common use cases

  • Automotive service

    Set a lb-ft torque wrench from a metric manual, or the reverse, without a 36 percent overtightening error.

  • Fastener engineering

    Restate a bolt torque chart in the unit a supplier, line worker or auditor expects.

  • Small fasteners and electronics

    Convert N·cm and oz-in screw specs for torque-limiting drivers on optics and circuit boards.

  • Restoring older machines

    Translate kgf·m figures in vintage Japanese and European manuals to modern N·m or lb-ft.

Tips and limitations

  • lb-ft and ft-lb mean the same torque in practice; physics texts reserve ft-lb for energy, but shop manuals use them interchangeably.
  • A quick sanity check: the N·m figure is always the larger number, about 1.36 times the lb-ft figure for the same torque.
  • Divide lb-ft by 12 to get nothing useful; multiply by 12 for lb-in. 15 lb-ft equals 180 lb-in, a common driver-bit spec range.
  • kgf·m specs in old manuals convert by 9.80665 exactly; the shortcut ×10 overshoots by 2 percent, which still matters at head-bolt torques.
  • Torque wrenches are least accurate at the bottom of their range, so convert first and pick the wrench whose scale puts the target near mid-range.

Sources and further reading

  1. NIST Special Publication 811: Guide for the Use of the International System of Units, NIST. Exact conversion factors for pound-force and foot-based units
  2. Pound-foot (torque), Wikipedia. Definition and the 1.3558 N·m equivalence
  3. Torque, Wikipedia. Why torque and energy share dimensions but not units

Frequently asked questions

How do you convert N·m to lb-ft?

Divide by 1.3558179483314004, the exact product of the pound-force (4.4482216152605 N) and the foot (0.3048 m). 110 N·m becomes 81.13 lb-ft. To go from lb-ft to N·m, multiply by the same factor.

Is ft-lb the same as lb-ft for a torque wrench?

For wrench settings, yes: both name pound-force times foot and shop manuals use them interchangeably. Physics texts keep ft-lb for energy and lb-ft for torque, but no torque wrench observes that distinction.

What happens if I set a lb-ft wrench to a N·m number?

You overtighten by about 36 percent, since each lb-ft is 1.356 N·m. A 110 N·m wheel spec dialed in as 110 lb-ft applies 149 N·m, enough to stretch studs or warp a brake rotor over time. Convert first, then set the wrench.

What is kgf·m and why do old manuals use it?

Kilogram-force meter: the torque of one kilogram of weight on a one-meter arm, exactly 9.80665 N·m by the standard-gravity definition. It was the common metric torque unit before SI adoption, so motorcycle and car manuals into the 1990s print specs like 3.5 kgf·m (34.3 N·m).

When are inch-pounds used instead of foot-pounds?

For small fasteners where a lb-ft scale lacks resolution. One lb-ft is 12 lb-in, so a 30 lb-in scope-ring screw is only 2.5 lb-ft, far below where a typical lb-ft wrench reads reliably. Electronics and firearms specs often go smaller still, into ounce-inches.

Why is torque in N·m and not joules if they are the same dimensions?

In torque the force acts perpendicular to the lever arm and no energy is transferred by the torque alone, while a joule is force along a displacement. The SI keeps the names apart to preserve that distinction, so torque is written N·m and never J.

Is there an in-depth guide to the Torque Unit Converter?

Yes. “Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets” covers the background, how it works, common pitfalls and worked examples. Read the full guide.