Force Converter
Convert force between newtons, kilonewtons, pound-force, kilogram-force, dynes and poundals with exact factors and the working shown step by step.
The interactive tool loads here when JavaScript runs.
About this toolWhat is the Force Converter?
Enter a force once and read it in newtons, kilonewtons, pound-force, kilogram-force, dynes, ounce-force and poundals at the same time. Pick any unit as the target and the converter writes out the steps for that pair, so 100 lbf becomes 100 × 4.4482216152605 = 444.82 N with the definition visible, not just the answer.
The factors are the exact ones from the standards, not rounded textbook values. One pound-force is 4.4482216152605 N exactly, because the avoirdupois pound is defined as 0.45359237 kg and standard gravity as 9.80665 m/s². One kilogram-force is 9.80665 N exactly for the same reason. Datasheets, bolt torque tables and load ratings mix these units constantly, and a rounding slip at the third digit matters when the number feeds a safety factor.
Everything runs in your browser and the values you type never leave your machine. The working steps name the exact definition used for each factor, the report bar under the tool exports the full conversion table as CSV or PDF, and the share link reproduces your input for a colleague.
- One input converts to all seven force units at once
- Step-by-step working for any chosen target unit, with the exact factor named
- Exact standards-based factors, not rounded values
- CSV and PDF export of the full conversion table from the report bar
- Runs entirely in the browser with a shareable link that restores your input
Updated
How to use the Force Converter
- Type the force value in the input field.
- Pick the unit you are starting from, for example pound-force.
- Read the result in every other force unit at once in the table.
- Select a target unit to see the step-by-step working with the exact factor and its definition.
- Export the table as CSV or PDF from the report bar, or copy the share link.
Worked examples
Pound-force to newtons and kilogram-force
Input
100 lbf
Output
444.82 N = 45.359 kgf
100 × 4.4482216152605 = 444.82216 N. Dividing by 9.80665 gives 45.359237 kgf, which is exactly the pound-to-kilogram mass factor, because both units assume the same standard gravity.
A person's weight as a force
Input
70 kgf
Output
686.47 N = 154.32 lbf
70 × 9.80665 = 686.4655 N. The mass stays 70 kg anywhere in the universe; the 686 N figure is the weight under standard gravity only.
Kilonewtons to pound-force
Input
1 kN
Output
224.81 lbf = 101.97 kgf
1,000 N ÷ 4.4482216152605 = 224.80894 lbf. This is the conversion you need to compare a European engine or actuator rating with a US one.
Newtons to dynes
Input
1 N
Output
100,000 dyn
The dyne is the CGS unit, 1 g·cm/s². Since 1 N is 1 kg·m/s², the ratio is 1,000 × 100 = 10⁵ exactly. Surface tension values are still often tabulated in dyn/cm.
Background and insight
The newton is the SI unit of force, defined through F = ma as the force that accelerates one kilogram at one metre per second squared. It was named at the 9th CGPM in 1948, and every other unit on this page is defined against it. The dyne is its CGS cousin, one gram centimetre per second squared, which makes 1 N exactly 100,000 dyn.
Pound-force and kilogram-force are gravitational units: each is the weight of the corresponding mass under standard gravity. That is where the confusion between weight and mass starts. A 70 kg person has a mass of 70 kg everywhere, but weighs 70 kgf, or 686.47 N, only where gravity is 9.80665 m/s². On the Moon the mass is unchanged while the weight drops to about a sixth. Bathroom scales, strain gauges and load cells all measure force and divide by an assumed gravity to display mass.
Rocketry is where the unit split is most visible. US engine thrust has traditionally been quoted in pounds-force, while European and Japanese manufacturers quote kilonewtons, so comparing engines means converting: 1 kN is 224.81 lbf. Thrust-to-weight ratio only comes out dimensionless when thrust and weight are expressed in the same force unit, which is exactly the conversion this tool does. The poundal, one pound mass times one foot per second squared, was an attempt to give the imperial system a coherent force unit like the newton; it survives mainly in older engineering texts.
Common use cases
Reading mixed datasheets
Compare actuator, spring and load-cell ratings quoted in N, lbf and kgf without re-deriving factors.
Structural and mechanical checks
Convert applied loads before plugging them into stress or safety-factor formulas that expect SI units.
Rocketry and propulsion
Put engine thrust figures quoted in kN and lbf on one scale to compare thrust-to-weight ratios.
Physics homework
Check weight-versus-mass problems, with the standard gravity constant and the working written out.
Tips and limitations
- kg is a mass, kgf is a force. A spec that says a bracket "holds 50 kg" almost always means 50 kgf, about 490 N.
- Both lbf and kgf bake in g₀ = 9.80665 m/s², so lbf to kgf is exactly the pound-to-kilogram factor, 0.45359237.
- Local gravity varies by about half a percent across Earth, so a force computed from a measured weight depends on where it was weighed.
- Ounce-force is a sixteenth of a pound-force; it turns up in small-motor and solenoid datasheets.
- If an old text uses poundals, it is using the coherent foot-pound-second system: 1 pdl = 0.138254954376 N exactly.
Sources and further reading
- The International System of Units (SI Brochure), BIPM. Definition of the newton and the status of kgf as a non-SI unit
- NIST Special Publication 811: Guide for the Use of the International System of Units, NIST. Exact conversion factors for lbf, kgf, dyne and poundal
- Pound (force), Wikipedia. History of the 1959 pound definition and standard gravity
Frequently asked questions
How many newtons are in one pound-force?
Exactly 4.4482216152605 N. The value follows from two exact definitions: the avoirdupois pound is 0.45359237 kg, and standard gravity is 9.80665 m/s². Multiplying them gives the factor this converter uses.
What is the difference between kg and kgf?
The kilogram is a unit of mass; the kilogram-force is the weight of that mass under standard gravity, 9.80665 N. Everyday language blurs the two because scales display mass, but ropes, hooks and brackets are rated by force.
Is weight a force?
Yes. Weight is the gravitational force on a mass, W = mg. A 70 kg person weighs 686.47 N under standard gravity, less at the equator and on the Moon, while their mass never changes.
Why do rocket engines quote thrust in both kN and lbf?
US manufacturers historically used pounds-force while European and Japanese ones use kilonewtons. 1 kN is 224.81 lbf, so a 1,000 kN engine produces about 224,809 lbf of thrust.
What is a dyne used for today?
The dyne is the CGS force unit, 10⁻⁵ N. It survives mainly in surface tension and adhesion work, where values are quoted in dyn/cm, and in older physics literature.
What is a poundal?
The poundal is the coherent force unit of the foot-pound-second system: the force that accelerates one pound mass at one foot per second squared, exactly 0.138254954376 N. It avoids the factor of g that pound-force carries.
Is there an in-depth guide to the Force Converter?
Yes. “Unit Conversion Factors: Exact Definitions, Gallons and Temperature Offsets” covers the background, how it works, common pitfalls and worked examples. Read the full guide.
Related Tools You May Like
Free, in-browser tools that pair well with this one.