Bolt Torque for Grade 4.6 and 8.8 Bolts, and Snug Tight
Torque in Nm and clamp force for grade 4.6 and 8.8 bolts (AS 4291.1), what snug tight means in AS 4100, and why 8.8/TB and 8.8/TF bolts are tensioned, not torqued.
By Redbison Dev · · 10 min read

Australia edition. Written for Australian workshops and steelwork: grade 4.6 commercial and 8.8 high-strength bolts to AS 4291.1 in N·m, AS 4100 bolting categories 8.8/S, 8.8/TB and 8.8/TF, the minimum bolt tensions, and how Queensland TMR checks them. US edition
An M20 grade 8.8 bolt with dry threads needs about 441 N·m to reach 75% of its proof load, a clamp force of 110.2 kN. That is the right kind of number for a machine base or a trailer drawbar. It is the wrong number for a fully tensioned structural joint, where the AS 4100 minimum bolt tension, as TMR's Technical Note 62 tabulates it, is 145 kN for an M20 bolt, essentially its whole proof load. The Australian version of the Bolt Torque Calculator works in newton metres for grade 4.6 and 8.8 bolts to AS 4291.1. This guide works through what it tells you in the workshop and on a steel job, and where torque stops being a reliable way to get tension.
Grade 4.6 and grade 8.8
Australian suppliers sell metric bolts in two main strengths: grade 4.6 commercial bolts and grade 8.8 high-strength bolts, with 10.9 and 12.9 for machine work. AS 4291.1 sets their mechanical properties. Structural grade 8.8 assemblies, bolt, nut and washer together, are made to AS/NZS 1252.1 and carry marks on all three parts.
| Grade | Proof stress | M16 proof load (156.7 mm²) | M16 torque, dry, 75% |
|---|---|---|---|
| 4.6 | 225 MPa | 35.3 kN | 84.6 N·m |
| 8.8 | 580 MPa (600 MPa above M16) | 90.9 kN | 218.1 N·m |
The calculator gets the torque from T = K x F x d: nut factor (0.20 for dry steel) times clamp force times nominal diameter. For the M16 grade 8.8 bolt at 75% of proof (68.2 kN) that comes to 218.1 N·m. A grade 4.6 bolt tightened to that figure would be loaded to about 193% of its proof load. Check the head before you pick up the rattle gun.
Thread condition moves the clamp force
Most of the torque is lost to friction under the nut and in the threads, so the same wrench setting gives very different clamp forces as the threads change. The calculator's nut factors follow Shigley's table: 0.20 for zinc-plated or unknown-finish dry steel (0.30 for plain black-oxide bolts), 0.18 oiled, 0.12 with anti-seize. Hot-dip galvanised bolts, common in outdoor steelwork, have their own friction, which the supplier or a calibration test should give you.
Example 1, a trailer drawbar on M16 grade 8.8. Dry threads and 75% of proof give 68.2 kN at 218.1 N·m. Oil the threads (K = 0.18) and the same clamp needs about 196.3 N·m. Use the dry 218.1 N·m on anti-seize (K = 0.12) and the clamp force jumps to about 113.6 kN, 125% of proof: the bolt has yielded. Use the torque that was written for the lubricant you use.
AS 4100 bolting categories
Structural steel in Australia is designed to AS 4100, which uses three categories of grade 8.8 bolting:
| Category | How it is tightened | How it carries load |
|---|---|---|
| 8.8/S | snug tight | bearing and shear |
| 8.8/TB | fully tensioned | bearing |
| 8.8/TF | fully tensioned | friction between the plies |
Queensland Transport and Main Roads (TMR) Technical Note 62 quotes the AS 4100 definition of snug tight: the tightness reached by a few impacts of an impact wrench or by the full effort of a person using a standard podger spanner, bringing the parts into firm contact. There is no torque value for snug tight.
The minimum bolt tensions
For 8.8/TB and 8.8/TF bolts, TN62 (November 2015) tabulates the minimum bolt tension from AS 4100-1998, the edition it references, and an upper limit. Check the current AS 4100 and AS/NZS 5131 for your project:
| Size | Minimum tension | Upper limit | Proof load in the calculator | Torque for the minimum, dry |
|---|---|---|---|---|
| M16 | 95 kN | 115 kN | 90.9 kN | 304 N·m |
| M20 | 145 kN | 185 kN | 146.9 kN | 580 N·m |
| M24 | 210 kN | 265 kN | 211.5 kN | 1,008 N·m |
| M30 | 335 kN | 420 kN | 336.4 kN | 2,010 N·m |
| M36 | 490 kN | 610 kN | 490.0 kN | 3,528 N·m |
The minimum is essentially the full proof load of the bolt. At M16 it is a little above the 90.9 kN the calculator gives for a class 8.8 bolt (ISO 898-1 uses 580 MPa up to M16), so do not treat a structural M16 as an ordinary machine bolt: follow the structural table. The last column is T = 0.20 x tension x d, the torque a dry bolt would need if the nut factor were exactly 0.20. It never is.
How TMR gets the tension
TN62 does not permit the part-turn method on TMR jobs, because of the variation in bolt tension it gives, and it explains why turning nuts by hand is not practical. A typical M24 structural bolt needs about 800 N·m to fully tension. That is the same as hanging 81 kg on the end of a 1 m spanner, or 204 kg at 400 mm on a normal 500 mm podger. People used to slip extensions over spanners to get there, which is unsafe and gives inconsistent tension.
Example 2, what 800 N·m does to an M24. Switch the calculator to preload from torque with 800 N·m on an M24 x 3 grade 8.8 bolt:
- lubricated nut factor 0.16: 208.3 kN, 98.5% of proof, roughly the 210 kN minimum
- dry nut factor 0.20: 166.7 kN, 78.8% of proof, about 20% short
Same wrench setting, same bolt, two very different joints. So the methods TN62 accepts all tie the wrench to measured tension:
- Load indicating washers where the bolt head and washer can be seen. For galvanised bolts TN62 requires a minimum gap of 0.25 mm between the head and the washer after tensioning. For "squirter" washers, each batch is calibrated in a bolt tension meter.
- Calibrated torque wrenches, electric (TN62 quotes an accuracy of ±4%), hydraulic or pneumatic, and a calibrated impact wrench only where bolts are too short for a load indicating washer. The setting is found by tensioning sample assemblies in a Skidmore-Wilhelm tension meter to the required tension and checking the wrench on a torque checker.
TN62 also asks for the threads to be lubricated with a stick wax before the nut goes on. Wax cuts thread friction, so if you model waxed threads in the calculator, enter a factor below 0.20 and then confirm the wrench setting against measured tension.
Example 3, snug tight is not a number. An M24 bolt brought up with 400 N·m on dry threads holds about 83.3 kN, 39% of proof. That might be a firm snug-tight joint, but it is well short of the 210 kN an 8.8/TF joint needs. Snug and fully tensioned are different categories, not two points on one chart.
Using the calculator in practice
- General machine and fabrication work: choose the grade and thread condition and aim at 75% of proof for joints you will take apart.
- Vehicles and equipment with a manual: the maker's figure wins. Use the calculator as a sanity check.
- AS 4100 8.8/TB and 8.8/TF bolting: follow AS 4100, AS/NZS 5131 for fabrication and erection, and the project specification. Use the calculator to see why the tension, not the torque, is what gets checked.
These figures are for preliminary design and checking. For structural, lifting and pressure joints, follow the code and have the joint checked by a qualified engineer.
Tools for this job
- Bolt Torque Calculator (grade 4.6 and 8.8): torque in N·m, clamp force and a size chart for grades 4.6 to 12.9.
- Tap Drill Size Calculator (Australia): the tapping drill for metric threads.
- Stress and Strain Calculator: how far the bolt stretches at that preload.
- Thermal Expansion Calculator: when bolt and plates are different metals that heat up.
The original guide to T = KFd has the long-form torque equation and the full nut factor table.
Frequently asked questions
What torque does an M20 grade 8.8 bolt need?
About 441 N·m dry at 75% of proof (110.2 kN). For a fully tensioned 8.8/TB or 8.8/TF joint the target is a tension of at least 145 kN, which would take about 580 N·m on dry threads and should be reached with load indicating washers or a calibrated wrench, not a chart.
What does snug tight mean in AS 4100?
The tightness reached by a few impacts of an impact wrench or by the full effort of a person using a standard podger spanner, enough to bring the plies into firm contact. It has no torque value.
Is grade 8.8 stronger than grade 4.6?
Yes. Its proof stress is 580 MPa up to M16 against 225 MPa for grade 4.6, so the same size carries about 2.6 times the clamp force.
How are load indicating washers checked?
With a feeler gauge in the gaps between the washer's bumps and the bolt head once the bolt is tensioned. TMR's note requires a minimum gap of 0.25 mm for galvanised bolts with conventional washers.
What is the difference between 8.8/TB and 8.8/TF?
Both are fully tensioned to the AS 4100 minimum. 8.8/TB joints carry load in bearing; 8.8/TF joints carry it by friction between the plies, so the condition of the contact surfaces matters as well as the bolt tension.
Sources and further reading
- Technical Note 62: Assembly and Tensioning of High Strength Bolts and Nuts, Part 1: Class 8.8, Queensland Department of Transport and Main Roads. AS 4100 categories, snug tight, minimum and upper bolt tensions, the 800 N·m M24 example and accepted tensioning methods.
- AS 4291.1:2015 Mechanical properties of fasteners, bolts, screws and studs, Standards Australia (store page).
- ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel, Part 1, ISO. Property classes and proof stresses.
- Shigley's Mechanical Engineering Design, McGraw Hill. Nut factors and recommended preload.
- Fastener Design Manual (NASA RP-1228), NASA. Torque, friction and preload scatter.
Open the Bolt Torque Calculator
More Mechanical
Every tool in the Mechanical section, free and in your browser.
- Torque and Power Calculator
- Gear Ratio Calculator
- Pulley and Belt Calculator
- Bolt Torque Calculator
- Spring Calculator
- Stress and Strain Calculator
- Bearing Life Calculator
- Hydraulic Cylinder Calculator
- Tap Drill Size Calculator
- Speeds and Feeds Calculator
- ISO Fits & Tolerances Calculator
- Bolt Circle Calculator
- Shaft Torsion Calculator
- Shaft Diameter Calculator
- Shaft Key Size Calculator