Bolt Torque in Nm: Classes, Clamp Load and Preloaded Bolts
Metric bolt torque in newton metres for BS EN ISO 898-1 classes, why copper grease changes the answer, and why UK preloaded bolts are not tightened from a chart.
By Redbison Dev · · 10 min read

United Kingdom edition. Written for UK workshops and steelwork: metric classes to BS EN ISO 898-1 in N·m, copper grease and anti-seize, classic-car UNF, DVSA wheel-nut re-checks, and how BS EN 14399 preloaded assemblies are tightened under BS EN 1090-2. US edition
An M12 class 8.8 bolt with dry threads needs about 88 N·m to reach 75% of its proof load, which clamps the joint with 36.7 kN. That figure is only right for that class, that size and dry threads. Put copper grease on the same bolt and 88 N·m stretches it past yield; swap it for a class 4.6 bolt and 88 N·m nearly doubles its proof load. The UK version of the Bolt Torque Calculator works in newton metres from BS EN ISO 898-1, and this guide shows how to read its answer for the jobs British workshops and fabricators actually do, from a bracket on a trailer to a preloaded splice in a steel frame.
The number on the head
Most bolts sold in the UK are metric coarse thread with an ISO property class stamped on the head. BS EN ISO 898-1 is the British publication of ISO 898-1, and it fixes the stresses behind each class:
| Class | Proof stress | Typical use |
|---|---|---|
| 4.6 | 225 MPa | low-strength commercial bolts, fencing and timber |
| 8.8 | 580 MPa to M16, 600 MPa above | general engineering, vehicles, structural steelwork |
| 10.9 | 830 MPa | machine tools, preloaded structural assemblies |
| 12.9 | 970 MPa | socket head cap screws in tooling |
Read 8.8 as 800 MPa nominal tensile strength (8 x 100) with yield at 0.8 of it, 640 MPa. Read 4.6 as 400 MPa tensile and yield at 0.6, 240 MPa. A bolt with no marking is of unknown strength and should not go into a structural or safety-critical joint.
The calculator's torque is the short-form equation T = K x F x d: nut factor times clamp force times nominal diameter. For an M12, the tensile stress area is 84.3 mm², so the class 8.8 proof load is 48.9 kN, 75% of it is 36.7 kN, and 0.20 x 36,656 N x 0.012 m comes to 88.0 N·m.
Lubrication decides the clamp force
Torque wrenches sold in Britain read in N·m first, and workshop manuals usually state whether a torque is for clean dry threads or oiled ones. That note matters more than the bolt class, because most of the torque is lost to friction under the nut and in the threads. The calculator's nut factor presets come from Shigley's table: 0.20 for zinc-plated or unknown-finish dry steel (0.30 for plain black-oxide bolts), 0.18 oiled and 0.12 with anti-seize compound.
Example 1, copper grease on a dry torque. A dry-thread figure of 88 N·m for an M12 class 8.8 bolt is applied to threads coated in copper grease (K = 0.12). Switch the calculator to preload from torque:
- clamp force 61.1 kN instead of 36.7 kN
- 125% of the proof load and a bolt stress of 725 MPa, 113% of minimum yield
The bolt has yielded during tightening. To reach the intended 36.7 kN with anti-seize, the wrench should be set to about 52.8 N·m. Copper grease goes on exhaust studs and anything else that might seize, so this mistake is easy to make. Use the torque the maker gives for the lubricant you actually use.
Example 2, a class 4.6 bolt with an 8.8 torque. A pack of zinc-plated M12 class 4.6 bolts is used to mount a trailer jockey wheel bracket, and someone sets the wrench to the 88 N·m they remember for 8.8. The calculator gives:
- class 4.6 at 75% of proof: 14.2 kN for 34.1 N·m
- 88 N·m on class 4.6: 36.7 kN, 193% of proof load, 181% of yield
The bolt necks or strips long before the wrench clicks. Check the head first.
Imperial threads on older British machinery
Classic cars, motorcycles and older machine tools may use UNF and UNC threads, and older still Whitworth (BSW) and BSF. The calculator covers UNC and UNF with SAE Grade 5 and Grade 8 properties. It does not cover Whitworth or BSF: their thread angle and pitches differ, so a "nearest" metric or Unified size gives the wrong stress area.
Example 3, a 3/8-24 UNF Grade 5 bolt on a classic car. Stress area 0.0878 in², dry, 75% of proof: 24.9 kN of clamp for 47.4 N·m, or 35.0 lb·ft. Where the car's workshop manual gives a figure, that figure wins; the calculator is a check that a figure from a forum is in the right range.
Wheel nuts on commercial vehicles
Wheel-nut torque comes from the vehicle maker, not from a bolt chart, because wheel studs, nut seats and wheel materials are designed together. For goods vehicles and buses, the DVSA Guide to Maintaining Roadworthiness repeats the industry code of practice: after a wheel is removed and refitted, check the wheel-nut torque once the vehicle has stood for 30 minutes, or after 40 to 80 km (25 to 50 miles), follow the maker's procedure, and record and keep every re-torque check. Wheel nuts settle as the seats bed in, which is the same embedding loss that relaxes any bolted joint after first tightening.
Preloaded bolts in steelwork are not tightened from a chart
In most UK buildings, structural bolts are non-preloaded. Bridges are different. SCI's guidance on steelconstruction.info says permanent connections in bridge steelwork are almost always made with preloaded bolts, that slip-resistant connections depend on that preload, and that preloaded bolts are seldom used in buildings, where slip and fatigue are less critical.
Preloaded assemblies are made to BS EN 14399 and tightened by a method in BS EN 1090-2. SCI notes three facts that every site supervisor should know:
- Only the HR and HRC systems are used in the UK (HV assemblies should never be mixed with them on a site).
- Each tightening method needs assemblies with a particular k-class: the torque method needs K2, the combined method K1 or K2, HRC K0 (with an HRD nut) or K2, direct tension indicators accept K0, K1 or K2, and the part-turn method in the Specification for Highway Works needs K0.
- Only K0 assemblies are currently manufactured in the UK.
A K0 assembly has no declared friction value, which is exactly what a torque method needs. So the common UK route is a direct tension indicator, an HRC bolt whose spline shears off at the set torque, or part-turn, not a figure from a torque table.
Example 4, why. BS EN 1993-1-8 sets the design preload of a preloaded bolt as Fp,C = 0.7 x fub x As. For an M20 class 10.9 bolt that is 0.7 x 1,000 MPa x 244.8 mm² = 171.4 kN, 84.3% of the calculator's proof load. Enter 84.3% and the calculator gives 685.4 N·m at K = 0.20. SCI says torque can vary by up to ±30% between bolts, even in a batch. Apply that same 685.4 N·m to a bolt whose real nut factor is 0.14 and the preload is 244.8 kN, 120% of proof; at 0.26 it is 131.8 kN, well short of Fp,C. Neither bolt looks any different. SCI also requires a preloaded bolt, nut and washer to be discarded if the nut is ever slackened after final tightening.
What to take from the calculator
- Generic machine joints: pick the class and the lubrication, target 75% of proof for joints you will take apart, and use the chart for the whole M3 to M36 range.
- Vehicles and equipment with a manual: use the manual, and use the calculator only to sanity-check the order of magnitude.
- Structural preloaded bolting: follow BS EN 1090-2 and the project specification. Use the calculator to understand why the tension, not the torque, is what gets specified.
These figures are for preliminary design and checking. For lifting equipment, pressure joints and structural connections, follow the maker's or code procedure and have the joint checked by a competent engineer.
Tools for this job
- Bolt Torque Calculator (UK): torque in N·m, clamp force and a size chart for classes 4.6 to 12.9.
- Tapping Drill Size Calculator (UK): the drill for metric and Unified threads.
- Stress and Strain Calculator: how far the bolt stretches at that preload.
- Thermal Expansion Calculator: when bolt and parts are different metals that heat up.
The original guide to T = KFd has the long-form equation and the full nut factor table with inch examples.
Frequently asked questions
What torque does an M12 8.8 bolt need in Nm?
About 88 N·m with dry or zinc-plated threads at 75% of proof load, clamping with 36.7 kN. With oiled threads (K = 0.18) the same clamp needs about 79 N·m, and with anti-seize (K = 0.12) about 53 N·m.
Can I use copper grease on bolts and keep the same torque?
No. Copper grease and other anti-seize compounds cut friction sharply. In example 1 an 88 N·m dry torque on a greased M12 8.8 bolt clamps at 61.1 kN, 125% of proof load. Reduce the torque, or use the maker's figure for greased threads.
Is a 4.6 bolt weaker than an 8.8 bolt?
Yes, much weaker. Class 4.6 has a proof stress of 225 MPa against 580 MPa for 8.8 up to M16, so an 8.8 bolt carries about 2.6 times the clamp force at the same size.
Why are UK preloaded structural bolts not torqued to a figure?
Because UK-made BS EN 14399 assemblies are class K0, with no declared friction value, and torque scatter of up to ±30% would leave some bolts short of preload and others overloaded. They are tightened with direct tension indicators, HRC shear-off bolts or the part-turn method.
When should wheel nuts be re-checked on a lorry or bus?
After the vehicle has stood for 30 minutes, or after 40 to 80 km (25 to 50 miles), following any wheel refit, according to the DVSA guide. Every re-torque check must be recorded and kept on file.
Sources and further reading
- Preloaded bolting, SCI and BCSA (steelconstruction.info). HR and HRC systems in the UK, k-classes by tightening method, K0 only made in the UK, torque scatter of up to ±30%, and discarding slackened assemblies.
- Tension Control Bolts, Grade S10T, in Friction Grip Connections (P324), SCI. Eurocode 3 bases the preload on a stress of 0.7 fub; Table 3.2 gives Fp,C = 171.5 kN for an M20 grade 10.9 bolt.
- Guide to maintaining roadworthiness: commercial goods and passenger carrying vehicles, Driver and Vehicle Standards Agency. Wheel-nut re-checks after 30 minutes or 40 to 80 km, and recording them.
- ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel, Part 1, ISO. Property classes and proof stresses, published in the UK as BS EN ISO 898-1.
- Shigley's Mechanical Engineering Design, McGraw Hill. Nut factors and recommended preload.
- Fastener Design Manual (NASA RP-1228), NASA. Torque, friction and preload scatter.
- VDI 2230 Part 1: Systematic calculation of highly stressed bolted joints, VDI. The long-form torque equation and joint analysis.
Open the Bolt Torque Calculator
More Mechanical
Every tool in the Mechanical section, free and in your browser.
- Torque and Power Calculator
- Gear Ratio Calculator
- Pulley and Belt Calculator
- Bolt Torque Calculator
- Spring Calculator
- Stress and Strain Calculator
- Bearing Life Calculator
- Hydraulic Cylinder Calculator
- Tap Drill Size Calculator
- Speeds and Feeds Calculator
- ISO Fits & Tolerances Calculator
- Bolt Circle Calculator
- Shaft Torsion Calculator
- Shaft Diameter Calculator
- Shaft Key Size Calculator