United Kingdom version. Metric by default: m², millimetres, tonnes and pounds, worked per course (binder and surface), with the England planning rule on impermeable front driveways. US version

Tarmac and Asphalt Calculator (UK)

Tonnes of tarmac (asphalt) for a driveway, path or patch from the area in m² and the compacted thickness of each course, with the price per tonne in pounds.

The interactive tool loads here when JavaScript runs.

About this tool

What is the Asphalt Calculator?

In the UK most people say tarmac for any black driveway, though what is laid today is asphalt concrete, bought by the tonne from a plant and laid in courses: a binder course and a thinner surface course on a compacted sub-base. This version works in square metres and millimetres. At the default compacted density of 2,320 kg/m³, each 10 mm of thickness weighs 23.2 kg per square metre.

Run the tool once for each course at the thicknesses your contractor or the council detail gives, and add the results. The planning rules matter here too: in England a new or replacement front driveway over 5 m² needs planning permission if it is impermeable and drains to the road, unless it is porous asphalt or drains to a lawn or border.

  • Rectangle, circle, triangle, trapezoid or known area
  • Editable compacted density with typical ranges for hot mix
  • Short tons and metric tonnes with automatic price conversion
  • Spread rate, truckloads and a thickness comparison table
  • Copy, share link and reset; nothing leaves your browser
Read the guide: Asphalt Tonnage: From Square Feet and Inches to Tons of Hot Mix

Updated

How to use the Asphalt Calculator

  1. Choose imperial or metric and the shape of the area to pave.
  2. Enter the dimensions, or pick Known area and type the area from a site plan.
  3. Enter the compacted thickness and check the density against your supplier's mix data.
  4. Add a waste allowance for edges, low spots and handwork, usually 3 to 10%.
  5. Enter the price per ton or tonne and the truck capacity to see cost and loads, then copy the result.

Worked examples

Driveway, 10 x 3.5 m, binder course 60 mm

Input

35 m², 60 mm compacted, 2,320 kg/m³, 5% extra

Output

2.1 m³; 5.12 tonnes

The binder course carries the load. Change the thickness to the figure in your quote; 5% covers edges and low spots in the sub-base.

Surface course on the same drive, 20 mm

Input

35 m², 20 mm compacted, 2,320 kg/m³, 5% extra

Output

1.71 tonnes; total for both courses 6.82 tonnes

A plant will usually supply the two mixes separately, so order them as two items. If the price per tonne differs, run the cost for each.

Background and insight

Asphalt plants and agency specifications describe placement as a spread rate. At 145 lb/ft³, one square yard one inch thick is 9 x (1/12) x 145 = 108.75 lb, which is why estimators use about 110 lb per square yard per inch. The same rule in metric is about 23 kg per square metre for each 10 mm. Compacted density, not the loose density in the truck, is what matters: the paver lays the mat loose and the rollers compact it by roughly 20 to 25% in thickness to reach the target air voids, typically around 7% in place for dense-graded mixes.

US suppliers quote short tons of 2,000 lb; most other countries use metric tonnes of 1,000 kg, and 1 tonne is 1.102 short tons. The calculator converts the price and truck capacity when you switch units so a quote stays comparable. Residential driveways are commonly 2 to 3 in (50 to 75 mm) of surface course on a compacted aggregate base; parking lots and roads carrying trucks need a pavement design, for example by the AASHTO method.

Common use cases

  • Driveway quotes

    Check that a contractor's tonnage matches the area and thickness they propose.

  • Patching and overlays

    Order the right amount of hot mix or cold patch for potholes and trench reinstatement.

  • Parking lots and site roads

    Compare a 2 in and a 3 in surface course in tonnage and cost.

  • Trucking plans

    Work out how many loads to schedule so the paver is never waiting for material.

Tips and limitations

  • If the drive crosses the pavement to the road you need a dropped kerb, which your council builds or approves; apply to them before you start.
  • Porous asphalt avoids the front garden planning condition in England but needs a permeable sub-base and a specialist contractor, as the government guidance points out.
  • Ask the supplier for the compacted density of their mix; dense asphalt is typically 2,200 to 2,450 kg/m³, and 2,320 is the default here.

Sources and further reading

  1. Guidance on the permeable surfacing of front gardens, Department for Communities and Local Government. The 5 m² rule and porous asphalt for driveways.
  2. Apply for a dropped kerb, GOV.UK
  3. Paving your front garden, Planning Portal

Frequently asked questions

How many tonnes of tarmac do I need for a driveway?

Area in m² x thickness in metres x density. For a 35 m² drive with 60 mm binder and 20 mm surface at 2,320 kg/m³ and 5% extra, that is 5.12 t plus 1.71 t, about 6.8 tonnes.

How much does a tonne of tarmac cover?

At 2,320 kg/m³, a tonne covers about 21.6 m² at 20 mm, 10.8 m² at 40 mm and 7.2 m² at 60 mm. The thickness table in the tool shows tonnes for 40 to 100 mm at once.

Do I need planning permission for a tarmac driveway?

In England, if you are surfacing more than 5 m² of a front garden with impermeable tarmac that drains towards the road, yes. You do not need it if you use porous asphalt or other permeable surfacing, or direct the water to a lawn or border to soak away. Rules differ in Scotland, Wales and Northern Ireland.

Is tarmac the same as asphalt?

In everyday speech, yes. Strictly, tarmacadam was a tar-bound stone; modern driveways are asphalt concrete bound with bitumen. Quotes may say tarmac, asphalt or bitmac for the same thing.

Does a tarmac driveway need a dropped kerb?

If cars will cross a pavement or verge to reach it, yes. In England and Wales you apply to your local council, which either builds the crossing or approves a contractor to do it.

Is there an in-depth guide to the Asphalt Calculator?

Yes. “Asphalt Tonnage: From Square Feet and Inches to Tons of Hot Mix” covers the background, how it works, common pitfalls and worked examples. Read the full guide.