How Many Plasterboards Do I Need for a Room?
Counting 2400 x 1200 plasterboards for walls and ceilings in square metres, screws per board, tape and jointing compound versus a skim, and HSE handling rules.
By Redbison Dev · · 9 min read

United Kingdom edition. Plasterboard as sold in the UK: 1200 mm boards, rooms in metres, screws from the stud centres, taping and jointing versus a plaster skim, HSE manual handling guidance, Artex ceilings and the Building Regulations sound requirement. US edition
A UK double bedroom of 3.6 by 3.0 metres with a 2.4 metre ceiling, one door and one window has 39.5 m² of wall and ceiling to board. At 2.88 m² a board and 10% for cuts, that is 16 boards of 2400 x 1200 mm, about 460 screws, and, if you tape and joint rather than skim, about 48 metres of tape and 15 litres of ready-mixed compound. The Plasterboard Calculator (UK) gives the same figures from your room and lets you change every rate; this guide shows how they are built and where a UK job differs.
Measure the board area in square metres
Unfold the room: the walls are one strip as long as the perimeter and as tall as the ceiling, and the ceiling sits on top.
walls = 2 x (length + width) x height
ceiling = length x width
For the bedroom, the walls are 2 x 6.6 x 2.4 = 31.68 m² and the ceiling 3.6 x 3.0 = 10.8 m², 42.48 m² in all. Take off the door (an 830 x 2020 mm opening, 1.68 m²) and the window (1200 x 1050 mm, 1.26 m²) and 39.54 m² is left.
Whether to take out small windows is a judgement call. The board usually goes up whole and the opening is cut out afterwards, so a small window saves an offcut you may not use. Doors and wide openings should come off.
British rooms add their own pieces. A chimney breast adds its two returns to the perimeter. Boxing-in round soil pipes and the void above a staircase are extra areas; add them in the calculator's extra-area box rather than stretching the room.
Boards, the 10% and tall rooms
boards = round up (net area / 2.88 x 1.10)
39.54 / 2.88 x 1.1 = 15.1, so 16 boards. Ten per cent covers the strips over doors, the pieces around windows and a damaged corner; awkward rooms with sloping ceilings or lots of short walls need more.
Order several rooms together and round once. Three bedrooms of the same size are 118.6 m², which is 46 boards ordered at once against 48 if each room is rounded up separately.
Tall Victorian and Edwardian rooms are where board length starts to matter. A 4.2 by 3.8 m front room with 2.7 m walls, a door and a 1200 x 1800 mm sash window has 39.4 m² of wall. In 2400 mm boards that is 16 boards; in 2700 mm boards hung vertically, 14, and each one runs floor to ceiling with no horizontal joint to fill. Ask your merchant which lengths they stock before you plan around them.
Screws follow the stud centres
The screw count comes from the board maker's fixing centres and your stud spacing, not from a fixed number per board. With screws at 300 mm along each stud:
| Studs at | Screws per 2400 x 1200 board | Per m² of board | Bedroom (46.08 m² of board) |
|---|---|---|---|
| 600 mm | 27 | about 9.4 | 432 |
| 400 mm | 36 | 12.5 | 576 |
The calculator's default of 10 per m² gives 461 screws for the bedroom's 16 boards. Check the maker's figure for ceilings separately, as it can differ from the wall figure. Screws are sold in boxes of fixed counts; round up to whole boxes.
Tape and joint, or skim?
This is the main UK difference from the American way of finishing. There are two routes, and only one needs the tape and compound figures:
- Skim. A plasterer applies a thin coat of finish plaster over the whole board. You order the finish plaster instead of jointing compound.
- Tape and joint (dry lining). Only the joints and screw heads are filled, with paper tape and jointing compound, and the board face is sealed and painted. It is done on tapered-edge boards and is usually the easier route to do yourself.
For tape and joint, the calculator's defaults are 121 m of tape and 37 litres of ready-mixed compound per 100 m² of board. The tape rate is the calculator's own estimate; the compound rate comes from US product data: USG says about two 4.5 US gallon pails of its ready-mixed all-purpose compound finish 1,000 sq ft of board, which is about 37 litres per 100 m². For the bedroom that is about 48 m of tape (one 75 m roll) and 14.6 litres (one 15 litre tub). Consumption varies with the finisher and the number of coats, so replace the rates with the coverage printed on the products you buy.
Which board, and the regulations around it
Standard board suits most walls and ceilings. Where the board maker recommends moisture-resistant board, such as in bathrooms, or a backer board made for tiling in a shower, order those separately.
Sound matters for new walls. Requirement E2 in Schedule 1 to the Building Regulations 2010 asks for reasonable resistance to sound in internal walls between a bedroom or a room containing a WC and other rooms, although it does not apply to a wall that contains a door or to the wall between an en suite toilet and its bedroom. The Planning Portal recommends asking the product maker or a building control body for a suitable build-up, which can change the board and insulation you order.
Re-boarding a ceiling in an older house raises a different question. HSE lists textured decorative coatings such as Artex among the places asbestos can be found in homes built or refurbished before 2000. Overboarding a sound ceiling avoids disturbing it; taking it down without knowing what is in it does not.
Handling the boards
A 2400 x 1200 board is awkward for one person, and some thermal and acoustic boards are much heavier. HSE's guidance on manual handling of plasterboard says special thermal or acoustic boards may weigh up to 50 kg each, that boards carried by hand should be a two-person job, and recommends ceiling lifts and props for overhead boards and a foot-operated board lifter for the bottom row of walls. It is written for building sites, but a hired plasterboard lifter is worth considering for any ceiling.
Fix the ceiling first so the wall boards support its edges, then the walls, staggering the joints between rows.
Frequently asked questions
How many plasterboards do I need for a 12 x 10 ft bedroom?
That is about 3.6 by 3.0 m. With 2.4 m walls, the ceiling, one door and one window, the net area is 39.5 m², which is 16 boards of 2400 x 1200 mm with 10% extra. Walls only would be 11 boards.
How many screws per sheet of plasterboard?
At 300 mm screw centres, a 2400 x 1200 board takes 27 screws on studs at 600 mm and 36 on studs at 400 mm. Your board maker's fixing centres are the figure to follow, and the ceiling figure can differ.
Do I need jointing compound if the room is being skimmed?
No. A skimmed room needs finish plaster instead. The calculator's tape and compound figures are for taping and jointing, where only the joints and screw heads are filled.
Are 2700 mm plasterboards worth it for high ceilings?
On 2.7 m walls they save boards and joints. A 4.2 by 3.8 m room with 2.7 m walls takes 14 boards of 2700 mm against 16 of 2400 mm, and each board covers the full height in one piece.
Is it safe to overboard an Artex ceiling?
Overboarding a sound textured ceiling avoids disturbing it. HSE lists textured coatings such as Artex among the materials that can contain asbestos in homes built or refurbished before 2000, so do not sand or scrape it, or have it tested before removal.
Sources and further reading
- Construction manual handling: plasterboard installation, Health and Safety Executive. Two-person carrying, ceiling lifts, board lifters and boards of up to 50 kg.
- The Building Regulations 2010, Schedule 1, legislation.gov.uk. Requirement E2 on sound resistance of internal walls and its exceptions.
- Building Regulations: Sound insulation for internal walls, Planning Portal.
- Diagrams showing where asbestos can occur in buildings, Health and Safety Executive. Textured coatings such as Artex.
- How much Sheetrock UltraLightweight All Purpose Joint Compound do I need?, USG. About two 4.5 gallon pails per 1,000 sq ft of board, the basis of the 37 L per 100 m² default.
- How much drywall, mud and tape? (US edition), RedBison. The same estimate in 4x8 sheets and gallons.
More Carpentry & Woodworking
Every tool in the Carpentry & Woodworking section, free and in your browser.